Siemens siprotec 7SD610 User Manual page 387

Addr. Parameter
3403 T-RECLAIM
3403 T-RECLAIM
3404 T-BLOCK MC
3406 EV. FLT. RECOG.
3407 EV. FLT. MODE
3408 T-Start MONITOR
3409 CB TIME OUT
3410 T RemoteClose
3411A T-DEAD EXT.
3420 AR WITH DIFF
3421 AR w/ SOTF-O/C
3423 AR WITH I.TRIP
3424 AR w/ DTT
3425 AR w/ BackUpO/C
3430 AR TRIP 3pole
3431 DLC / RDT
3433 T-ACTION ADT
3434 T-MAX ADT
3435 ADT 1p allowed
3436 ADT CB? CLOSE
3437 ADT SynRequest
3438 T U-stable
3440 U-live>
3441 U-dead<
3450 1.AR: START
3451 1.AR: T-ACTION
3453 1.AR Tdead 1Flt
3454 1.AR Tdead 2Flt
3455 1.AR Tdead 3Flt
3456 1.AR Tdead1Trip
3457 1.AR Tdead3Trip
3458 1.AR: Tdead EV.
3459 1.AR: CB? CLOSE
3460 1.AR SynRequest
3461 2.AR: START
3462 2.AR: T-ACTION
3464 2.AR Tdead 1Flt
3465 2.AR Tdead 2Flt
7SD610 Manual
C53000-G1176-C145-4
Function C Setting Options
Auto Reclose 0.50 .. 300.00 sec
Auto Reclose 0.50 .. 300.00 sec; 0
Auto Reclose 0.50 .. 300.00 sec; 0
Auto Reclose with PICKUP
with TRIP
Auto Reclose Stops AutoRecl
starts 3p AR
Auto Reclose 0.01 .. 300.00 sec
Auto Reclose 0.01 .. 300.00 sec
0.00 .. 300.00 sec; ∞
Auto Reclose
0.50 .. 300.00 sec; ∞
Auto Reclose
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose WITHOUT
DLC
0.01 .. 300.00 sec; ∞
Auto Reclose
Auto Reclose 0.50 .. 3000.00 sec
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose 0.10 .. 30.00 sec
Auto Reclose 30 .. 90 V
Auto Reclose 2 .. 70 V
Auto Reclose YES
NO
0.01 .. 300.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
Auto Reclose 0.01 .. 1800.00 sec
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
0.01 .. 300.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
0.01 .. 1800.00 sec; ∞
Auto Reclose
Default Setting
3.00 sec Reclaim time after successful AR
cycle
3.00 sec Reclaim time after successful AR
cycle
1.00 sec AR blocking duration after
manual close
with TRIP Evolving fault recognition
starts 3p AR Evolving fault (during the dead
time)
0.50 sec AR start-signal monitoring time
3.00 sec Circuit Breaker (CB) Supervision
Time
0.20 sec Send delay for remote close
command
∞ sec
Maximum dead time extension
YES AR with differential protection ?
YES AR with switch-onto-fault over-
current ?
YES AR with intertrip ?
YES AR with direct transfer trip ?
YES AR with back-up overcurrent ?
YES 3pole TRIP by AR
WITHOUT Dead Line Check / Reduced
Dead Time
0.20 sec Action time
5.00 sec Maximum dead time
NO 1pole TRIP allowed
NO CB ready interrogation before re-
closing
NO Request for synchro-check after
3pole AR
0.10 sec Supervision time for dead/live
voltage
48 V Voltage threshold for live line or
bus
30 V Voltage threshold for dead line or
bus
YES Start of AR allowed in this cycle
0.20 sec Action time
1.20 sec Dead time after 1phase faults
1.20 sec Dead time after 2phase faults
0.50 sec Dead time after 3phase faults
1.20 sec Dead time after 1pole trip
0.50 sec Dead time after 3pole trip
1.20 sec Dead time after evolving fault
NO CB ready interrogation before re-
closing
NO Request for synchro-check after
3pole AR
NO AR start allowed in this cycle
0.20 sec Action time
1.20 sec Dead time after 1phase faults
1.20 sec Dead time after 2phase faults
A.7 Settings
Comments
387