Download  Print this page

Burst Gate Pulse Width Adjustment (rv109); Ntsc Subcarrier Frequency Adjustment (rv1400); Pal Subcarrier Frequency Adjustment (rv1401); Ntsc Comb Filter Adjustment (rv1, T1/cfm101) - Sony TRINITRON PVM-8042Q Service Manual

S mic chassis color video monitor.
Hide thumbs

Advertisement

5-2-3. Burst Gate Pulse Width Adjustment
(RV109)
Input signal: Color bars signal (LINE A/VIDEO IN)
Switches:
UNDER SCAN
16 : 9
SYNC INT/EXT
LINE/RGB
1. Connect an oscilloscope to pin 10 (COMP SYNC) of
CN104 and pin 1 (BGP GEN) of IC113.
2. Adjust the pulse width (T) with RV109 (BGP WIDTH)
as shown below.
Specification: T = 7.8 ± 0.2 usec
IC113 PIN-1
CN104 PIN/0
5-2-4. NTSC Subcarrier Frequency Adjustment
(RV1400)
Input signal: NTSC Color bars signal (LINE A/VIDEO IN)
Switches:
UNDER SCAN
16 : 9
SYNC INT/EXT
LINE/RGB
1. Apply +5 V to pin 26 of IC113 via 4.7 kZ resistor.
2. Connect pin 2 of IC109 to ground.
3. Connect the following circuit to pin 1 of IC113.
Part Required
Resistor 18 kZ ....................................................... 1 pc
Diode 1SS133 ........................................................ 4 pcs
R276
3
1
113
2
4. Connect the frequency counter to pin 21 of IC113.
5. Adjust the frequency with RV1400 (3.58 F0).
Specification: F0 = 3,579,545 ± 20 Hz
MIC
S
Chassis
8 Pull (OFF)
8 Pull (4 : 3)
8 INT
8 LINE
T = 7.8 ±0.2 uSec
8 Pull (OFF)
8 Pull (4 : 3)
8 INT
8 LINE
+12 V
18 k
1S133 (x 4)
R211
5-2-5. PAL Subcarrier Frequency Adjustment
(RV1401)
Input signal: PAL Color bars signal (LINE A/VIDEO IN)
Switches:
UNDER SCAN
16 : 9
SYNC INT/EXT
LINE/RGB
1. Apply +5 V to pin 26 of IC113 via 4.7 kZ resistor.
2. Connect pin 2 of IC109 to +12 V line.
3. Connect the following circuit to pin 1 of IC113.
Part Required
Resistor 18 kZ ....................................................... 1 pc
Diode 1SS133 ........................................................ 4 pcs
R276
3
1
113
2
4. Connect the frequency counter to pin 21 of IC113.
5. Adjust the frequency with RV1401 (4.43 F0).
Specification: F0 = 4,433,619 ± 20 Hz
5-2-6. NTSC Comb Filter Adjustment
(RV1, T1/CFM101)
Input signal: NTSC Color bars signal (LINE A/VIDEO IN)
Switches:
UNDER SCAN
16 : 9
SYNC INT/EXT
LINE/RGB
1. Connect an oscilloscope to minus (_) terminal of
capacitor C202, and confirm the Y and residual chroma
levels.
Specification:
= 0.78 ± 0.05 Vp-p
Y level
Residual chroma level = 32 mVp-p or less
2. If the residual chroma level is out of specification,
adjust RV1 and T1 alternately so that it is minimum.
C202 (_)
0.78 ±0.05 Vp-p
8 Pull (OFF)
8 Pull (4 : 3)
8 INT
8 LINE
+12 V
18 k
1S133 (x 4)
R211
8 Pull (OFF)
8 Pull (4 : 3)
8 INT
8 LINE
Residual chroma:
32 mVp-p or less
5-5

Advertisement

Table of Contents

   Also See for Sony TRINITRON PVM-8042Q

Comments to this Manuals

Symbols: 0
Latest comments: