Sony TRINITRON PVM-8042Q Service Manual page 19

Power Sources
House Current (for all models)
Connect the supplied AC power cord to the AC IN
socket and to a wall outlet.
to AC IN
to a wall outlet
To connect an AC power cord securely with AC plug holders.
1 2
AC IN socket
AC power plug
AC plug holder A
1
Remove the AC IN socket screws and then use
them to attach the AC plug holder A (supplied) to
the AC IN socket.
2
Plug the power cord to the AC IN sokcet. Then,
attach the supplied AC plug holder B on top of the
AC power cord.
Rechargeable Battery (PVM-9045QM/9042QM only)
The monitor can operate with one or two battery packs.
For extended use, two battery packs are recommended.
EJECT
buttons
NP-1B
(not supplied)
SONY mark downwards
10
(GB)
For the PVM-9045QM/9042QM
When the AC power cord is plugged into the AC IN
socket, the battery pack (if installed) or the DC 12 V
IN jack (if connected) is automatically disconnected.
3
AC plug
holder B
3
Slide AC plug holder B over the cord until is locks.
To remove the AC power cord
Pull out AC plug holder B by squeezing the left and
right sides.
To remove the battery pack, press the EJECT button
upwards.
For charging, use the BC-1WDCE for the NP-1B.
Note
Make sure you disconnect the cables connected to the
connectors (AC IN, DC 12 V IN) at the rear of the
monitor. Otherwise, the monitor cannot operate on the
battery pack(s).
Specifications
Video signal
Colour system PVM-9045QM/9042QM: PAL,
SECAM, NTSC, NTSC
4.43
PVM-9040ME: PAL, SECAM
Resolution PVM-9045QM: 450 TV lines
PVM-9042QM/9040ME: 250 TV
lines
Aperture correction –4.0 dB to +6.0 dB (at 3.0 MHz)
Frequency response 6.0 MHz (–3.0 dB)
Synchronization AFC time constant 1.0 msec.
Picture performance
Normal scan 6% over scan of CRT effective
screen area
Underscan 3% underscan of CRT effective
screen area
H. linearity Less than 5.0% (typical)
V. linearity Less than 5.0% (typical)
Convergence Central area: 0.43 mm (typical)
Peripheral area: 0.53 mm
(typical)
Raster size stability H: 1.0%, V: 1.5%
High voltage regulation
3.0%
Colour temperature D65
Inputs and Outputs
Model PVM-9045QM PVM-9040ME
Connector PVM-9042QM
LINE A Y/C IN yes yes
Y/C OUT yes yes
VIDEO IN yes yes
VIDEO OUT yes yes
AUDIO IN yes yes
AUDIO OUT yes yes
LINE B VIDEO IN yes no
VIDEO OUT yes no
AUDIO IN yes no
AUDIO OUT yes no
RGB/ R/R-Y IN yes no
COMPONENT G/Y IN yes no
B/B-Y IN yes no
AUDIO IN yes no
EXT SYNC IN yes no
OUT yes no
REMOTE yes no
Inputs Y/C IN: 4-pin mini DIN
connector
See the pin assignment on page
12 (GB).
VIDEO IN: BNC connector
1 Vp-p ± 6 dB, sync negative
a)
AUDIO IN: phono jack, –5 dBu
less than 47 kohms
R/R-Y, G/Y, B/B-Y: BNC
connector
R, G, B channels: 0.7 Vp-p,
± 6 dB Sync on green: 0.3 Vp-p,
negative
R-Y, Y, B-Y channels: 0.7 Vp-p,
±6 dB (Standard colour bar
signal of 100% chrominance)
EXT SYNC IN: BNC connector
Composite sync 4 Vp-p, ±6 dB,
negative
Loop-through outputs
Y/C OUT: 4-pin mini DIN
connector, 75 ohms terminated
(75 ohms automatic termination)
VIDEO OUT: BNC connector,
75 ohms terminated (75 ohms
automatic termination)
AUDIO OUT: phono jack
EXT SYNC OUT: BNC
connector, 75 ohms terminated
Speaker output Output level: 0.5W
Remote input REMOTE: 8-pin mini DIN
connctor (75 ohms automatic
termination)
See the pin assignment on page
12 (GB).
a) 0 dBu = 0.775 Vr.m.s.
General
Power consumption & requirements
PVM-9045QM/9042QM:
0.7 to 0.4A 43W at 100 to 240V
AC operation
3.7A 40W at 12 V DC operation
PVM-9040ME:
0.7 to 0.4A 39W at 100 to 240V
AC operation
Operating conditions
Temperature 0 to +35°C (32 to 95°F)
Humidity 0 to 90% (no condensation)
Pressure 700 to 1060 hPa
11
(GB)
,