Sony TRINITRON PVM-8042Q Service Manual page 18

Location and Function of Parts and Controls
Rear
PVM-9045QM/9042QM
@¢ COMPONENT
LEVEL selector
@∞ RGB/COMPONENT
input connectors
@§ AC IN socket
@¶ EJECT buttons
@• BATTERY compartments
!• LINE A connectors (PVM-9045QM/9042QM)
!• LINE connectors (PVM-9040ME)
Y/C IN (4-pin mini DIN): Connect to the Y/C
separate output of a video camera, VCR or other
video equipment.
Y/C OUT (4-pin mini DIN): Loop-through output of
the Y/C IN connector. Connect to the Y/C separate
input of a VCR or another monitor.
VIDEO IN (BNC): Connect to the video output of a
video camera, VCR or other video equipment.
VIDEO OUT (BNC): Loop-through output of the
VIDEO IN connector. Connect to the video input
of a VCR or another monitor.
AUDIO IN (phono jack): Connect to the audio
output of a VCR or a microphone (through a
suitable microphone amplifier).
AUDIO OUT (phono jack): Loop-through output of
the AUDIO IN connector. Connect to the audio
input of a VCR or another monitor.
Note
The Y/C IN connector has a priority over the VIDEO
IN connector.
When a plug is connected to the Y/C IN connector, the
VIDEO IN connector is automatically disconnected.
8
(GB)
!• LINE A connectors
!ª LINE B connectors
@º REMOTE connector
(8-pin mini DIN)
@¡ EXT SYNC (external sync)
connectors
@™ V HOLD (vertical hold) control
@£ DC 12V IN jack (XLR, 4 pin)
Note
(PVM-9045QM/9042QM only)
To monitor the signal fed through these connectors,
keep the LINE/RGB selector and the A/B, RGB/Y R-Y
B-Y selector on the front panel released (LINE and A).
!ª LINE B connectors
To monitor the signal fed through these connectors,
keep the LINE/RGB selector released (LINE) and
depress the A/B, RGB/Y R-Y B-Y selector on the front
panel (B).
VIDEO IN (BNC): Connect to the video output of a
video camera, VCR or other video equipment.
VIDEO OUT (BNC): Loop-through output of the
VIDEO IN connector. Connect to the video input
of a VCR or another monitor.
AUDIO IN (phono jack): Connect to the audio
output of a VCR or a microphone (through a
suitable microphone amplifier).
AUDIO OUT (phono jack): Loop-through output of
the AUDIO IN connector. Connect to the audio
input of a VCR or another monitor.
PVM-9040ME
@§ AC IN socket
@º REMOTE connector (8-pin mini DIN)
Connect to the tally output of a control console,
special-effect generator, etc. The tally lamp on the
front panel will be turned on and off by the connected
equipment. This connector can be used for connecting
a remote controller.
For the pin assignment of this connector, see
"Specifications" on page 12 (GB).
@¡ EXT SYNC (external sync) connectors
IN (BNC): When this monitor operates on an
external sync signal, connect the reference signal
from a sync generator to this connector. In this
case, depress the SYNC INT/EXT selector on the
front panel (EXT).
OUT (BNC): Loop-through output of the EXT
SYCN IN connector. Connect to the external sync
input of video equipment to be synchronized with
this monitor.
@™ V HOLD (vertical hold) control
Turn to stabilize the picture if it rolls vertically.
@£ DC 12V IN jack (XLR, 4 pin)
Connect the Sony battery adaptor DC-L10 (not
supplied).
@¢ COMPONENT LEVEL selector
Select the component level from among two modes.
N10/SMPTE: for 100/0/100/0 signal
BETA 0: for 100/0/75/0 signal
!• LINE connectors
@™ V HOLD (vertical hold)
control
@∞ RGB/COMPONENT input connectors
R/R-Y, G/Y, B/B-Y (BNC), AUDIO (phono):
To monitor a signal fed through these connectors,
depress the LINE/RGB selector on the front panel
(RGB). When the SYNC INT/EXT selector on the
front paner is released (INT), the monitor operates on
the sync signal from the G/Y channel.
To monitor the analog RGB signal
Connect to the analog RGB signal outputs of a video
camera. Keep the A/B, RGB/Y R-Y B-Y selector on
the front panel released (RGB).
To monitor the component signal
Connect to the R-Y/Y/B-Y componenet signal outputs
of a Sony BetaCam video camera. Depress the A/B,
RGB/Y R-Y B-Y selector on the front panel (Y R-Y B-
Y).
@§ AC IN socket
Connect the supplied AC power cord to this socket and
to a wall outlet.
@¶ EJECT buttons
Press the EJECT button upwards to remove the battery
pack.
@• BATTERY compartments
Insert the NP-1B battery pack (not supplied).
9
(GB)