Maintenance; Carbon Brushes; Description Of Symbols/Electrical Safety; Troubleshooting - Ozito ROTARY TOOL SET Original Instructions Manual

MAINTENANCE

• Keep the ventilation vents of the rotary tool clean at all times, if possible,
prevent foreign matter from entering the vents.
• After each use, blow air through the rotary tool housing to ensure it is free
from all dust particles which may build up. Build up of dust particles may
cause the rotary tool to overheat and fail.
• If the enclosure of the rotary tool requires cleaning, do not use solvents but
a moist soft cloth only. Never let any liquid get inside the rotary tool; never
immerse any part of the rotary tool into a liquid.
• If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.

Carbon Brushes

When the carbon brushes wear out, the rotary tool will spark and/or stop.
Discontinue use as soon as this happens. They should be replaced prior to
recommencing use of the rotary tool. Carbon brushes are a wearing component
of the rotary tool therefore not covered under warranty. Continuing to use the
rotary tool when carbon brushes need to be replaced may cause permanent
damage to the rotary tool. Carbon brushes will wear out after many uses but
when the carbon brushes need to be replaced,
take the rotary tool to an electrician or a power tool
repairer for a quick and low cost replacement. Always
replace both carbon brushes at the same time.
Note: Ozito Industries will not be responsible for any
damage or injuries caused by the repair of the rotary
tool by an unauthorised person or by mishandling of
the rotary tool.
DESCRIPTION OF SYMBOLS
V Volts
~ Alternating current
/min Revolutions or
reciprocation per minute
mm
Millimetres
Double insulated
Warning
Wear ear protection
Hz Hertz
W Watts
n
o No load speed
Diameter
Read instruction manual
Wear eye protection
ELECTRICAL SAFETY
WARNING! When using mains-powered tools, basic safety precautions,
including the following, should always be followed to reduce risk of
fire, electric shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off
in an emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future
reference.
Before you connect the equipment to the mains supply make sure that the data on
the rating plate are identical to the mains data.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool
repairer in order to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury
resulting from a possible electrical insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of
an extension lead not suitable for the power input of the tool or which is damaged or
defective may result in a risk of fire and electric shock.

TROUBLESHOOTING

Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Excessive sparking visible through the housing air vents
and/or the rotary tool failing to operate
May indicate the carbon brushes have worn out and need to be
replaced. Carbon brushes should only be replaced by a qualified
electrician or power tool repairer.
SPARE PARTS
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: enquires@ozito-diy.co.uk