Table of Contents
Advertisement
Item
Counter 0 to 2 Event
Source
Counter 0 to 2 Event
Activation
Counter 0 to 2 Reset
Counter 0 to 2 Refresh
Counter 0 to 2 Value
Counter 0 to 2 Status
h) User Set Control
User Set Selector
User Set Load
User Set Save
i) Sequencer Control
Sequencer Mode
Sequencer Mode Select
Sequencer Configuration Mode
Sequencer Set Selector
Sequencer Frame Number
Sequencer Set Next
Sequencer Width
Sequencer Height
Sequencer Offset X
Sequencer Offset Y
Sequencer Gain
Sequencer Exposure Time
(US)
Sequencer Black Level
Sequencer LUT Enable
Sequencer H Binning
(GO-2400M-USB only)
Sequencer V Binning
(GO-2400M-USB only)
Sequencer Repetition
Sequencer LUT Mode
Sequencer Set Active
Sequencer Command Index
Sequencer Set Start
Sequencer Reset
j) Chunk Data Control
Chunk Mode Active
Setting range
Off, Frame Trigger,
Frame Start,
Exposure Start,
Exposure Transfer End
Rising Edge (fixed)
—
—
—
—
Default,
User Set1 to User Set3
—
—
On, Off
Trigger Sequencer,
Command Sequencer
On, Off
1 to 128
1 to 255
0 (Off), 1 to 128
GO-2400M-USB:
16 to 1216
GO-2400C-USB:
16 to 1936
2 to 1216
0 to (1936 - Width)
0 to (1218 - Height)
100 to 1600
6 to 8000000
-133 to 255
True, False
1 to 2
1 to 2
1 to 255
Gamma, LUT
—
1 to 128
1 to 128
—
True, False
— 49 —
GO-2400M-USB / GO-2400C-USB
Default value
Off
Select the counter event signal for which
to read the count value.
Rising Edge
Specify the timing at which to count.
—
Reset the counter.
—
Update the count value.
0 to 2
Display the count value.
Counter Active
Display the counter status.
Configure user settings.
Default (factory
Select the user settings.
default values)
—
Load user settings.
—
Save the current setting values as user
settings.
Configure sequencer settings.
Off
Enable/disable [Sequencer Mode].
Trigger
Select the sequencer mode.
Sequencer
On
Select [On] to change the settings within
the index.
1
Select the [Trigger Sequencer] mode and
[Command Sequencer] mode index.
1
Set the number of frames to display for
the selected Sequencer Index. (Enabled
only for Trigger Sequencer.)
1
Set the next index to be displayed for the
selected Sequencer Index. (Enabled only
for Trigger Sequencer.)
1936
Set the width of the selected Sequencer
Index.
1216
Set the height of the selected Sequencer
Index.
0
Set the horizontal offset value for the
selected Sequencer Index.
0
Set the vertical offset value for the
selected Sequencer Index.
100
Set the gain for the selected Sequencer
Index.
6210
Set the exposure time for the selected
Sequencer Index.
0
Set the black level for the selected
Sequencer Index.
False
Enable/disable the LUT setting for the
selected Sequencer Index.
1
Set the horizontal binning for the selected
Sequencer Index.
1
Set the vertical binning for the selected
Sequencer Index.
1
Set the repeat count for the sequencer.
Gamma
Set the sequencer LUT mode.
—
Displays the active LUT number.
1
Set this to change the Sequencer Index.
(Enabled only for Command Sequencer.)
1
Set the index number that is used when
executing [Sequencer Reset] in [Trigger
Sequencer] mode.
—
Reset the current index number to the
number configured in [Sequencer Set
Start].
Configure Chunk Data function settings.
False
Enable/disable the Chunk Data function.
Description
Advertisement
Table of Contents
