Fdum Series (Rcn-Kit3-E) - Mitsubishi SCM40ZS-S Technical Manual

(3) FDUM series (RCN-KIT3-E)

Receiver amp kit
Notes:
Following functions of FDUM indoor unit series are not able to be set with this wireless
Installation Manual
remote control (RCN-KIT3-E).
1. 4-fan speed setting (PHi/Hi/Me/Lo)
Read this manual together with the installation manual attached to Read this manual together with the installation manual attached to
the air conditioner.
the air-conditioner.
WARNING
✟ Fasten the wiring to the terminal securely and hold the cable securely so as not to
Fasten the wiring to the terminal securely and hold the cable securely so as not to
apply unexpected stress on the terminal.
apply unexpected stress on the terminal.
Loose connection or hold will cause abnormal heat generation or fire.
Loose connection or hold will cause abnormal heat generation or re.
✟ Make sure the power supply is turned off when electric wiring work.
Make sure the power source is turned off when electric wiring work.
Otherwise, electric shock, malfunction and improper running may occur.
Otherwise, electric shock, malfunction and improper running may occur.
✟ DO NOT install the wireless kit at the following places in order to avoid malfunction.
DO NOT install the wireless kit at the following places in order to avoid malfunction.
(1)Places exposed to direct sunlight
(1)Places exposed to direct sunlight
(2)Places near heat devices
(2)Places near heat devices
(3)High humidity places
(3)High humidity places
(4)Hot surface or cold surface enough to (9)Places where the receiver is affected by
(4)Hot surface or cold surface enough to
generate condensation
generate condensation
(5)Places exposed to oil mist or steam directly
(5)Places exposed to oil mist or steam directly
(6)Uneven surface
(6)Uneven surface
(7)Places affected by the direct airflow of the
(7)Places affected by the direct air ow of the
AC unit.
AC unit.
✟ DO NOT leave the wireless kit without the cover.
DO NOT leave the wireless kit without the cover.
In case the cover needs to be detached, protect the receiver with a packaging box or
In case the cover needs to be detached, protect the receiver with a packaging box or
bag in order to keep it away from water and dust.
bag in order to keep it away from water and dust.
Attention
Attention
• Instruct the customer how to operate it correctly referring to the instruction manual.
• Instruct the customer how to operate it correctly referring to the instruction manual.
• User's manual of a wireless remote control is attached to a indoor unit or a outside unit.
• User's manual of a wireless remote control is attached to a indoor unit or a outside unit.
• Read this together with a manual attached to this kit.
• Read this together with a manual attached to this kit.
①Accessories
① Accessories
Please make sure that you have all of the following accessories.
Please make sure that you have all of the following accessories.
Receiver 1
1
Receiver 1
1
Wiring (3m) 1
2
Wiring (3m) 1
2
Parts set (A) 1
3
Parts set (A) 1
3
Parts set (B) 1
4
Parts set (B) 1
4
Parts set (C) 1
5
Parts set (C) 1
5
Wireless remote
6
1
Wireless remote
6
control
1
control
User's manual 1
7
7 User's manual
1
②Wireless remote control's operable area
② Wireless remote control's operable area
(1) When installed on ceiling
(1) When installed on ceiling
① Standard reachable area of the signal
① Standard reachable area of the signal
condition Illuminance at the receiver : 300lux (when no lighting is installed within
Illuminance at the receiver : 300lux (when no lighting is installed within
Condition
1m of the receiver in an ordinary of ce.)
1m of the receiver in an ordinary of ce.)
Orientation of receiver
Orientation of receiver
Receivable area
Receivable area
of the signal
of the signal
Orientation of receiver
Orientation of receiver
Receivable area
Receivable area
of the signal
of the signal
② Correlation between illuminance at the receiver and reachable area of the signal in a plain
② Correlation between illuminance at the receiver and reachable area of the signal in a plain view.
view.
condition Correlation between the reachable area of the signal and illuminance at
the receiver when the remote control is operated at 1.1m high under the
Condition Correlation between the reachable area of the signal and illuminance at
condition of ceiling height of 2.5m.
the receiver when the remote control is operated at 1m high under the
When the illuminance becomes double, the area is narrowed down to two third.
condition of ceiling height of 2.4m.
When the illuminance becomes double, the area is narrowed down to two third.
(2) When installed on wall
Illuminance at the receiver :
condition
The receivable area of the signal when
800lux.
the illuminance at the receiver is 300lux.
The receivable area of the signal when
the illuminance at the receiver is 300lux.
The receivable area of the signal when
the illuminance at the receiver is 600lux.
The receivable area of the signal when
the illuminance at the receiver is 600lux.
(2) When installed on wall
Condition Illuminance at the receiver : 800lux.
Wireless
remote control
Floor
5m or less
Wireless
remote control
Floor
5m or less
3-fan speed setting (Hi/Me/Lo)
PJZ012D060
PJZ012D060A
WARNING
CAUTION
CAUTION
(8)Places where the receiver is influenced by
(8)Places where the receiver is in uenced by
the fluorescent lamp (especially in verter
the uorescent lamp (especially inverter
type) or sunlight.
type) or sunlight.
(9)Places where the receiver is affected by
infrared rays of any other communication
infrared rays of any other communication
devices.
devices.
(10)Places where some object may obstruct the
(10)Places where some object may obstruct the
communication with the remote control
communication with the remote control
Remote control
1
Remote control 1
1
holder 1
holder
2 Screw for holder 2
Screw for holder 2
2
AAA dry cell
AAA dry cell 2
3
battery (R03)
2
3
battery (R03)
Screw for receiver 2
1
2
Screw for receiver
1
Fixing band 1
2
Fixing band 1
2
Clamp 5
3
Clamp 5
3
Screw for clamp 5
4
Screw for clamp 5
4
1 Receiver installation
1
Receiver installation
1
bracket
1
bracket
Screw for the bracket 2
2
Screw for the bracket 2
2
Installation fitting 2
3
Installation tting 2
3
Receiver
Receiver
Ceiling surface
Ceiling surface
Floor
Floor
Ceiling surface
Ceiling surface
Floor
Floor
Receiver
Receiver
60° or less
60° or less
③ How to install the receiver
③How to install the receiver
The following two methods can be used to install the receiver onto a ceiling or a wall.
Select a method according to the installation position.
The following two methods can be used to install the receiver onto a ceiling or a wall.
<Installation position>
Select a method according to the installation position.
(A) Direct installation onto the ceiling with wood screws.
<Installation position>
(B) Installation with accessory's bracket
(A) Direct installation onto the ceiling with wood screws.
(B) Installation with accessory's bracket
Drilling of the ceiling (ceiling opening)
(1)
(1) Drilling of the ceiling (ceiling opening)
Drill the receiver installation holes with the following dimensions at the ceiling position where
wires can be connected.
Drill the receiver installation holes with the following dimensions at the ceiling position where
wires can be connected.
(A) Direct installation onto the ceiling with
wood screws.
(A) Direct installation onto the ceiling with
(B) Installation with enclosed bracket.
wood screws.
(B) Installation with enclosed bracket
Wiring connection of receiver
(2)
(2) Wiring connection of receiver
Caution
Caution
Do not connect the wiring to the
power source of the terminal block.
Do not connect the wiring to the
If it is connected, printed board will
power source of the terminal block.
be damaged.
If it is connected, printed board will
be damaged.
Installation of the receiver
(3)
Installation of the receiver
(3) Remove the screw on the side of the receiver and sprit it into the upper case and lower
case.Install the receiver with one of the two installation methods (A) or (B) shown below.
Remove the screw on the side of the receiver and sprit it into the upper case and lower
case.Install the receiver with one of the two installation methods (A) to (C) shown below.
(A) Direct installation onto the ceiling with screws
(A) Direct installation onto the ceiling with screws Use this installation method when the ceiling is wooden, and there is no problem for
strength in installing directly with wood screws.
Use this installation method when the ceiling is wooden, and there is no problem for
Wall opening
strength in installing directly with wood screws.
Wall opening
101
①Put through the wiring from the back side to the hole of the lower case.
②Fit the lower case into the ceiling opening. Make sure that the clearance between
①Put through the wiring from the back side to the hole of the lower case.
the convex part of the back of the lower case and the ceiling opening must be as
②Fit the lower case into the ceiling opening. Make sure that the clearance between equal as possible on both sides.
③Using the two installation holes shown above, fix the lower case onto the ceiling
the convex part of the back of the lower case and the ceiling opening must be as
with the enclosed wood screws. (The other four holes are not used.)
equal as possible on both sides.
③Using the two installation holes shown above, x the lower case onto the ceiling
④Connect the wiring with the wiring from the upper case by the connector.
⑤Take out the connector to the backside from the hole of the lower case putting
with the enclosed wood screws. (The other four holes are not used.)
④Connect the wiring with the wiring from the upper case by the connector.
through the wiring at ①.
⑤Take out the connector to the backside from the hole of the lower case putting
⑥Fit the upper case and the lower case, and tighten the screws.
through the wiring at 1.
⑥Fit the upper case and the lower case, and tighten the screws.
(B) Installation with enclosed bracket
Use this method when installaing onto a gypsum board (7 to 18mm), etc.
(B) Installation with enclosed bracket
Use this method when installaing onto a gypsum board (7 to 18mm), etc.
Installation fitting
Installation tting
Protrusion
(right side of center)
Protrusion
(right side of center)
Bracket Protrusion (left side of center)
①Catch the two protrusion of the enclosed bracket onto the tting as shown above,
and temporarily fix with the screws. (The bracket has an up/down and front/back
Bracket Protrusion (left side of center)
orientation. Con rm the top/bottom protrusion positions and the positional relation
①Catch the two protrusion of the enclosed bracket onto the tting as shown above,
of the ø 10 holes on the bracket and the installation hole on the lower case with the
and temporarily x with the screws. (The bracket has an Upper/Lower and
above drawing.)
front/back orientation. Con rm the Upper/Lower protrusion positions and the
②Insert the end of the installation tting into the back of the ceiling from the opening,
positional relation of the ø 10 holes on the bracket and the installation hole on the
and tighten the screws to fix the bracket onto the ceiling.
lower case with the above drawing.)
③Pass the wiring from the rear side through the hole on the lower case.
②Insert the end of the installation
④Fit the lower case onto the bracket, and fix the lower case to the bracket using the
and tighten the screws to x the bracket onto the ceiling.
two installation holes shown above. (The other four holes are not used.)
③Pass the wiring from the rear side through the hole on the lower case.
⑤Follow step ① to ⑥ for (A) to complete the installation.
④Fit the lower case onto the bracket, and x the lower case to the bracket using the
two installation holes shown above. (The other four holes are not used.)
⑤Follow step 1 to 6 for (A) to complete the installation.
298
- -
'16 • SCM-T-199
88mm(H)×101mm(W)
88mm(H)×101mm(W)
108mm(H)×108mm(W)
108mm(H)×108mm(W)
Indoor unit terminal block
Indoor unit terminal block
(non-polarized)
(non-polarized)
Lower case
Installation hole
Hole
Lower case
Installation hole
Hole
Wiring
Wiring
Installation hole
Wiring
Wiring
Upper case
Upper case
Hole
Connector Lower case
Hole
Connector Lower case
[Top]
Protrusion
(right side of center)
[Top]
Bracket
Hole
Protrusion
(ø10)
(right side of center)
Hole (ø10)
Bracket
Hole
[Bottom]
(ø10)
Bracket
Hole (ø10)
Protrusion (left side of center)
[Bottom]
Bracket
Protrusion (The center of right and left)
Lower case
Installation hole
[Top]
Hole
Lower case Hole
Wiring Installation hole
[Upper]
Hole
Lower case
Hole
Wiring
Installation hole
[Bottom]
Lower case
Installation hole
[Lower]
tting into the back of the ceiling from the opening,
W
Wiring
Wiring
Reciever
Reciever
Opening
Opening
Hole
Lower case
Hole
Lower case
Installation hole