Major Components And Accessories - Zip Command-Centre Installation Instructions Manual

Parts supplied
Tap options
Command-Centre
QUICK START GUIDE STEP 1-
Prepare and fit the Taps
Note: This quick start guide must be read in conjunction with HydroTap Tap All-In-One Tap
the main installation and user instructions (If required)
• Before proceeding, read the installation and user instructions
For AIO mains and vented Taps
• Check all the components are present and correct.
• Cut a 50mm hole in the bench / sink top.
Check that you have all the necessary tools
• Ensure the underbench can support the product weight when full of water,
(Check the specifications in the main book and allow an extra 5-8kg when full. )
Black plastic SINK TOP
spacer
Before installing ensure the following have been provided at 50mm
the installation site: ALL THREAD
ROD Stainless
• Sufficient space in the cupboard to install all of the undersink units in accordance washer
with these Installation Instructions. Refer to technical specification for dimensions. If NOTE: make sure the tap location will allow the nozzle to drain into the sink.
required, make allowance for a booster heater. (Refer to the main book, for detailed SPIDER
Fit the CLAMP
installation instructions). STAINLESS
• A potable water supply connection with isolating valve inside the cupboard within BLACK STAINLESS STEEL
reach of the flexible braided hose and positioned so that the connection point and the PLASTIC STEEL WASHER, 6mm
SPACER WASHER SPIDER CLAMP, NUT
stop cock will not be obstructed when all the undersink units are installed. AND 6mm NUT.
• For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will be
required. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will be SPIDER
CLAMP
required. (One GPO is for the Zip HydroTap and the other for the Booster heater). NOTE: feed each of the three tubes and
NOTE: Check the cable lengths and outlet positions before proceeding. electrical cable evenly in between the legs of O-RING
• A potable cold water supply with a minimum working pressure of 172kPa and a NUT the SPIDER CLAMP when installing.
maximum working pressure of 700kPa connected via an isolation valve. 35mm dia hole
• For the mains pressure All-IN-ONE, both a hot and cold water supply will be required. Hole positioning: BASE
Position the tap such that it dispenses into BLOCK ALL
• The undersink appliances must be mounted in upright positions as shown in the the sink bowl with ample clearance for a cup or tea pot. Alternatively, SPIDER THREAD O-RING
diagrams. the tap could be mounted away from the sink using a Zip Font, avail- ROD SINK TOP
Sink
able as an accessory. BASE
IMPORTANT! BLOCK
Do not proceed with the installation if these Apply a light smearing of silicon sealant NUT
requirements are not met. USB
on the underside of the upper spacer to CABLE
ensure a watertight fi t.
Parts Supplied Description Parts Supplied Description
Mixer Tap
Fit the O-ring to the underside of the AIO tap
4-in-1 (If required) then pass all hoses through the 50mm hole.
Duct kit
1 off 1x Air Duct
Hydrotap Tap
and hoses 1 x Mounting
plate
Tap
Vent kit O ring Base
1 off UPPER
Undersink Unit 1 x Kickboard RUBBER UPPER RUB-
louvre WASHER BER WASHER Chiller
with air and water- 1 x Door vent
filter Clear tube to Vent connection
louvre BLUE
1 x front vent grill LOWER RUBBER NOTE: feed each of
WASHER LOWER RUB- the tubes and elec- Boiler
BER WASHER
trical cable evenly in connection
1 off WASHER WASHER between the legs of RED
1 x Restrictaflow HydroTap the BASE BLOCK
valve and Tee Booster heater NUT
BRAIDED SPIDER.
piece for Mixer and hoses NUT
Taps (Supplied with HOSE x 3
240/175 models) White Hose White ring Blue ring on
For HydroTap and Mixer taps Ext. Mains on LHS to RHS mains IN to
Mains in Mixer IN
cut a 35mm hole in the bench / sink top.
1 off Mains water Blue band
BENCH TOP Mixer IN From Mixer OUT to Tap - Vented version only
connection hose
Ø35mm Red band
Mixer Out
801600 - Zip Quick Start Guide - October 2013 - V1.06
Page 8 of 20

Major components and accessories

Description
1 x HydroTap
Classic
Elite or Arc / Cube
#
(inc. Tube kit)
#
and components
TM
Vent kit
2 x outlet vent
1 x inlet vent
1 x
Command-Centre
with air and water
filters
1 x Mains water
connection hose
1 x User guide and
ZIP HydroTap
®
User Guide
1 x Quick start
Tap Operation...................(Pages 2-5)
•
LCD Screen & Menu .......(Pages 6-18)
•
Maintenance.................... (Pages 18-20)
•
Date of Installation.........
•
BC160/125G4
BC240/175G4
BCH160/125G4
BCH240/175G4
AV160/125G4 guide
AN160/125G4
AV240/175G4
AN240/175G4
1 x Installation
Affix Model Number Label
Here
801599
instruction
801599 - HydroTap User Guide - Nov 2013 UK - V1.05 Page 1 of 20
1 x
CO gas cylinder
2
assembly
804052UK - Residential chilled and sparkling installation instructions - Sept 2016 - v3.02
Accessories
G4
®
TM
For Accessories contact Zip:
Tel 0345 6 005 005
Website: www.zipwater.com/uk
Email: sales@zipindustries.co.uk
Description
Font kit
Classic & Elite
or
Arc / Cube
Replacement
internal 0.2 micron
filter
Disabled lever kit
(Classic HydroTap )
®
1 X
CO gas cylinder
2
Recommended
water block