Zip HydroTap G4 User Manual
Water chiller/boiler
Hide thumbs
Also See for HydroTap G4:
- User manual (560 pages) ,
- Installation instructions manual (40 pages) ,
- Installation and operating instructions manual (28 pages)
Related Manuals for Zip HydroTap G4
Summary of Contents for Zip HydroTap G4
- Page 1 ZIP HydroTap G4 ® User Guide Affix model number label here 802254UK 802254UK -G4 Comm - Res Boiling chilled compact User Guide - July 2015 - V2.01 Page 1 of 24...
- Page 2 Table of contents ap safety ..........Page 2 • T • Tap operation ........... Pages 3 to 7 • Safety sensor calibration ......Page 8 • Tap lights ..........Page 8 to 9 • LCD screen & menu ......... Pages 10 to 22 •...
- Page 3 Tap operation To dispense boiling water (with the safety lock off) Classic Depressing the red BOILING lever allows the dispensing of boiling water. Pulling forward the red BOILING lever allows the tap to operate in a “no-touch” mode. Water will flow from between 5 and 15 seconds (this is user adjustable, see page 22).
- Page 4 Tap operation To dispense chilled water Classic Depressing the blue CHILLED lever allows the dispensing of chilled water. Pulling forward the blue CHILLED lever allows the tap to operate in a “no- touch” mode. Water will flow from between 5 and 15 seconds (this is user adjustable, see page 22).
- Page 5 Tap operation Arc / Cube On powerup, wait 30secs. for the unit to calibrate before selecting either the boiling red illuminated with safety, or chilled blue illuminated water mode, by touching the select button. The Arc / Cube control may be rotated in a forward or reverse Rotary control...
- Page 6 Tap operation Classic mixer tap Lifting the lever up will Increase flow Cold increase the flow rate Decrease flow and lowering the lever will decrease the flow rate. Lower the lever all the way down to close the tap. When the lever is moved in the direction of the blue dot, the temperature is decreased and when moved...
- Page 7 Tap operation All-in-One tap (for functionality other then the mixer tap operation, see Classic models) The top of the All-in-One tap is operated in the same manner as a Classic HydroTap G4. The two ® levers are used for dispensing boiling and chilled water.
- Page 8 Safety sensor calibration (Classic models) Light intensity varies from site to site, therefore it is recommended that a recalibration be performed at the time of the installation. All direct sunlight must be shaded from the HydroTap G4, during the ® calibration.
- Page 9 Tap lights Warning light all models Filter light Red warning light Flashing warning light When the indicator light flashes fast and continuous, a system fault has occurred. Check for details on the faults screen. If unable to rectify, call a qualified service agent.
- Page 10 LCD Screen Zip HydroTap G4 features a ‘TOUCH’ screen for easy setup and operation ® adjustment. (See page 24 for home menu icons). Other possible messages in status window: Status** Information Notes Safety OFF Product is in normal operation mode...
- Page 11 LCD Screen menu Main Sub menu Sub menu Section menu options Language English / Deutsch • Product info. • Module Revision Serial number Information Product number Calibration • Filters log • Filters • System faults • Faults found • Filter flush •...
- Page 12 LCD Screen operation - Section A A. Set language • Press the [MENU] button for main menu. • Press the [Language] button. • Select the country. • Press [<=] button for the previous menu. LCD Screen operation - Section B B.
- Page 13 LCD Screen operation - Section C C. Install Once your Zip HydroTap G4 unit has been installed, Go to the install menu to ® configure the system settings for your product. Sub menu 1. - Filter flush. 2. - Filter reset.
- Page 14 Caution In general, boiling water units may vent steam from the tap spout. Take care to avoid personal injury whenever this occurs. The Zip HydroTap G4 is equipped with a self-calibrating program. On start ® up, the controls take the system through a calibration process. Once this mode is completed the system reverts back to normal operation.
- Page 15 This can only be done by a Zip technician. Please contact your Zip service provider for further assistance.
- Page 16 LCD Screen operation - Section E E. Security The Zip HydroTap G4 allows the appliance coordinator to set up a password ® to protect against users changing the preferred system settings. To set a password • Press the [MENU] button for main menu.
- Page 17 • Press [NEXT] button to set time. Set temperature Zip HydroTap G4s are designed to operate within 1ºC to 2ºC of set point for ® boiling water and between 6ºC to 10ºC for chilled drinking water. All boiling water units are self calibrating to 98ºC, which is the recommended setting.
- Page 18 LCD Screen operation - Section G Filter Zip HydroTap G4 allows the user to adjust filter life and edit filter usage. ® To edit the filter life Press the [MENU] button for main menu. • Press the [Settings] button. •...
- Page 19 LCD Screen operation - Section G Energy modes This mode allows the HydroTap G4 to go into energy saving mode. There ® are two options available: sleep mode and on/off mode. In sleep mode the unit will go to “Sleep” after a 2hr period of inactivity. The boiling water will gradually drop to either 68°C or room temp, as shown in the table below and the chilled water will be ON or OFF.
- Page 20 LCD Screen operation - Section G Note Any attempt, during off mode, to dispense water, will bring the unit out of sleep mode. The unit will return to sleep mode after 2 hours of non use. Please allow sufficient time for the water to reach the set temperature after disabling the sleep mode.
- Page 21 LCD Screen operation - Section G Safety To allow the safety setting to be changed using the touch screen • Press the [MENU] button for main menu. • Press the [Settings] button. • Enter your 4-digit password and press [Enter]. •...
- Page 22 LCD Screen operation - Section G Dispense Times The ability to change the maximum dispensing time for both the hot and cold water has been introduced. The default settings for the maximum dispensing times is 15 seconds. The operator may change both the hot and cold dispensing times from 5 to 15 seconds, in increments of 1 second.
- Page 23 Filter maintenance • Caution. A small amount of water will drip as the cartridge is removed. • Do not tilt the cartridge as water may spill from it if tilted. • Unpack replacement cartridge and remove sanitary cap, write today’s date where shown on the label.
- Page 24 Mobile: 0345 6 005 005 Norfolk NR191TE As Zip policy is one of continuous product improvement, changes to specifications may be made without prior notice. Images in this booklet have been modified and may not be true representations of the finished goods.