Page 3
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer PORTEGE R200, referred to as PORTEGE R200 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
Page 4
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the PORTEGE R200 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
Page 5
Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the PORTEGE R200 that appears on its display is presented in the type face below: Format complete...
2.11 LAN ......................... 2-45 2.12 Sound ........................2-47 2.13 Bluetooth Troubleshooting ..................2-49 2.14 Wireless LAN Troubleshooting................2-52 2.15 SD card slot......................2-55 2.16 Fingerprint sensor ....................2-56 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 7
3.25 System Configuration ....................3-60 3.26 Wireless LAN Test Program (Atheros) ..............3-62 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program ..........3-69 3.28 Sound Test program....................3-84 3.29 SETUP ........................3-90 PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 8
4.22 LED FPC......................4-42 4.23 Display mask...................... 4-43 4.24 FL inverter/LCD unit ..................4-45 4.25 Hinge........................4-48 4.26 Wireless LAN antenna/Bluetooth antenna............4-52 4.27 Fluorescent Lamp....................4-54 viii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 9
Keyboard Scan/Character Codes ............... D-1 Appendix E Key Layout....................E-1 Appendix F Wiring diagrams..................F-1 Appendix G BIOS rewrite procedures................G-1 Appendix H EC /KBC rewrite procedures ..............H-1 Appendix I Reliability.....................I-1 PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
1.1 Features 1 Hardware Overview Features Features The PORTEGE R200 is an ultra thin and lightweight PC realizing cable-less environment on a table by wireless function with an Intel Mobile Pentium-M processor realizing high performance. Microprocessor Intel Mobile Pentium-M A 1.2GHz processor with a 400MHz external clock, 100MHz bus and 0.94/0.81V core operation.
Page 16
The SD Card Slot can accommodate Secure Digital flash memory cards with various capacities. Sound system Incorporates an internal monaural speaker, stereo headphone jack and HW volume. One touch button TOSHIBA Assist Button and TOSHIBA Presentation Button are available. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com...
Page 17
The internal wireless LAN supports Mini PCI Type III (802.11a/b). Fingerprint sensor The computer is equipped with a fingerprint sensor and fingerprint authentication utility. They enable only person who has registered his/her fingerprint to use the computer. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
1 Hardware Overview 1.1 Features Figure 1-1 shows the front of the computer and Figure 1-2 shows the system units configuration. Figure 1-1 Front of the computer [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 19
1.1 Features 1 Hardware Overview Figure 1-2 System units configuration PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
The keyboard is mounted 84(US)/85(UK) keys that consist of character key and control key. The keyboard is connected to membrane connector on the system board and controlled by the keyboard controller. See Appendix E about a layout of the keyboard. 1-12 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
5. Turns the power supply on and off. 6. Provides more accurate detection of a low battery. 7. Calculates the remaining battery capacity. 8. Controls the transmission of the status signal of the main battery. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-15 Downloaded from www.Manualslib.com...
AD1981B, Amp, Mic Amp, Line In, Line Out PC Card Power, USB Power Temperature reset IC, LEDs 2.0 - 3.5 ICH6-M(RTC) D-E5V Dock Power D-E3V Dock Power 1-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
The main battery is the primary power supply for the computer when the AC adapter is not connected. In stand-by (instant recovery) mode, the main battery maintains the current status of the computer. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-17 Downloaded from www.Manualslib.com...
Table 1-8 RTC battery charging/data preservation time Time Charging AC adapter or main battery in use 8 hours (approx.) Data preservation time (when fully charged) 1 month 1-18 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Input voltage 100V to 240V Input frequency 50Hz/60Hz Input voltage 0.6A to1.1A 1.5A or less Output voltage DC 15V Output current 0A to 3.0A 0A to 4.0A PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-19 Downloaded from www.Manualslib.com manuals search engine...
7. PC with a serial port (for displaying debug port test result) 8. Wraparound connector for PC card 9. Tester 10. External Monitor 11. External USB Keyboard 12. External USB mouse 13. Headphone 14. Microphone 15. LAN wraparound connector PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Ask user to enter the password if a password is registered. Make sure that Toshiba Windows OS is installed on the hard disk. Non-Toshiba operating systems can cause the computer malfunction. Make sure all optional equipment is removed from the computer.
Page 45
12. If any failure error is detected on the SD card, perform the SD card Troubleshooting Procedures in Section 2.15. 13. If any failure error is detected on the Fingerprint sensor, perform the Finger Sensor Troubleshooting Procedures in Section 2.16. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Doesn’t light Any condition other than those above. *1 When the power supply controller detects a malfunction, the DC IN icon blinks orange. It shows an error code. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 48
If the DC IN icon does not light, go to Procedure 3. Check 3 If the battery icon does not light orange or blue, go to Procedure 4. NOTE: Use a supplied AC adapter (G71C0001A310/A410, G71C0004A210) only. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Interval between data bits Off for half second The error code begins with LSB (Least Significant bit) Example: Error code 11h (Error codes are given in hexadecimal format.) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 50
Current from the DC power supply is over 4.95A. Current from the DC power supply is over 0.5A when there is no load. Abnormal current has been sensed 0[A]. 2-10 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 51
E5V voltage is under 4.50V when the computer is booting up. E5V voltage is over 4.50V while the computer is powered off. E5V voltage is under 4.50V while the computer is suspended. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-11 Downloaded from www.Manualslib.com...
Page 52
PPV voltage is under 0.56V when the computer is powered on. PPV voltage is under 0.56V when the computer is booting up. PPV voltage is over 0.56V when the computer is powered off. 2-12 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 53
Connect a new AC adapter and AC power cord. If the error still exists, go to Procedure 5. Check 3 In the case of error code 21h: Go to Procedure 3. Check 4 For any other errors, go to Procedure 5. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-13 Downloaded from www.Manualslib.com manuals search engine...
Make sure the battery pack is installed in the computer correctly. If the battery is properly installed and the battery icon still does not light, go to Procedure 4. 2-14 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Battery pack may be faulty. Replace it with a new one. If the problem still occurs, perform Check 2. Check 2 System board may be faulty. Replace the system board with a new one. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-15 Downloaded from www.Manualslib.com...
1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Debug port Check Procedure 3: Diagnostic Test Program Execution Check Procedure 4: Replacement Check 2-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
System board is damaged. Go to Procedure 3. WARNING: RESUME FAILURE. PRESS ANY KEY TO CONTINUE. If any other error message is displayed, perform Check 3. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-17 Downloaded from www.Manualslib.com manuals search engine...
3. Connect the RS-232C cross-cable to the PC that displays the results. RS-232C cross-cable Debug port test cable PC that displays Test board CN3400 System board the test results 4. Boot the computer in MS-DOS mode. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-19 Downloaded from www.Manualslib.com manuals search engine...
Page 60
6. When the D port status is FFFFh (normal status), go to Procedure 3 7. When the D port status falls into any status in Table 2-4, execute Check 1. 2-20 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 61
Configuration of DRAM Permission of cache (only L1 cache) Memory Clear Shifts to real mode and copies BIOS on RAM. F009H Stores key scan code. Setting of TASK_1ms_TSC PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-21 Downloaded from www.Manualslib.com manuals search engine...
Page 62
Initialization of ICH.D31.Func1/2 Initialization of USB Controller Initialization of ICH.D31.Func3 Initialization of ICH AC97 Audio Initialization of TI Controller PIT CH1 initialization (Setting refresh interval to 30ms) 2-22 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 63
Returning to ROM Turning area of C0000h to EFFFFh to PCI (Prohibition of DRAM) Setting of resume error request Copying ROM/RAM of system BIOS (HLT at error) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-23 Downloaded from www.Manualslib.com manuals search engine...
Page 64
Setting of CPU clock to “high” F107H Storing memory configuration in buffer Reading EC version Update of flash ROM type Initialization of ACPI table (for executing an option ROM) 2-24 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 65
Initialization of SIO (SIO supporting model) Initialization of FIR (FIR supporting model) PCI automatic configuration Creating a work area for auto configuration Acquisition of PCIIRQ Configuration Storing the results of VGA configuration PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-25 Downloaded from www.Manualslib.com manuals search engine...
Page 66
CHECK_DMAC (Check of DMAC) (Boot) F11AH INIT_DMAC (DMAC initialization) (Boot) F11BH CHECK_PRT (Check of printer port existence) (model supporting PRT) F11CH CHECK_SIO (Check of SIO) (model supporting SIO) 2-26 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 67
Bluetooth initialization (Bluetooth supporting model) Check whether a target maintenance card is set Disabling a PC card not used Setting of Wake UP status data for ACPI PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-27 Downloaded from www.Manualslib.com manuals search engine...
Page 68
Contents F003H or F004H Error of security initialization F00BH Prohibition of BIOS renewal F117H Exception check error F120H Error of Setting clock generator F122H Logo display error 2-28 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
If connectors are properly plugged, but there is still a problem, go to Check 2. Check 2 The system board may be damaged. Replace the system board with a new one following the steps described in Chapter 4, Replacement Procedures. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-29 Downloaded from www.Manualslib.com...
Procedure 2. Detailed operation is given in Chapter 3, Tests and Diagnostics. If the test program cannot be executed on the computer, go to Procedure 3. 2-30 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 71
“write enable”. If any other message appears, perform Check 2. Write protected Check 2 Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-31 Downloaded from www.Manualslib.com...
FDD is still not functioning properly, perform Check 3. Check 3 Replace the system board with a new one following the steps in Chapter 4, Replacement Procedures. 2-32 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
User’s Manual. Procedure 1 Partition Check Insert the Toshiba MS-DOS system disk and start the computer. Perform the following checks: Check 1 Type C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Procedure 2.
Page 74
The 1.8” HDD and the connector of HD FPC and the system board may be disconnected (Refer to the steps described in Chapter 4, Replacement Procedures for disassembling.). Insert the connectors firmly. If they are firmly connected, go to Procedure 3. 2-34 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 75
If the 1.8” HDD is formatted, set the 1.8” HDD partition using MS-DOS FDISK command. If you cannot format the 1.8” HDD using the Tests and Diagnostic program, go to Procedure 4. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-35 Downloaded from www.Manualslib.com...
Page 76
ECC error ECC recover enable HDC error Seek error Time out error Drive not ready Undefined error Write fault Status error Access time out error No HDD 2-36 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Chapter 4, Replacement Procedures and check the operation. If the problem still occurs, perform Check 4. Check 4 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-37 Downloaded from www.Manualslib.com...
Chapter 4, Replacement Procedures. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. 2-38 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Refer to Chapter 3, Tests and Diagnostics for details. This program checks the display controller on the system board. If an error is detected, go to Procedure 3. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-39 Downloaded from www.Manualslib.com...
Chapter 4, Replacement Procedures. If the connections are loose, reconnect firmly and restart the computer. If the problem still occurs, go to Procedure 4. 2-40 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Chapter 4, Replacement Procedure and test the display again. If the problem still occurs, perform Check 5. Check 5 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedure. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-41 Downloaded from www.Manualslib.com...
If there is still an error, go to Procedure 3. System board Touch Pad CN3240 Procedure 3 Replacement Check The touch pad or touch pad cable may be damaged. Replace them with a new one. 2-42 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Execute Modem test in the LAN/Modem/Bluetooth/IEEE1394 test program. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program. If any error is detected by the test, go to Procedure 2. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-43 Downloaded from www.Manualslib.com...
Chapter 4. If the modem function is still not working properly, perform Check 6. Check 6 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. 2-44 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Execute LAN test in the LAN/Modem/Bluetooth/IEEE1394 test program. Refer to Chapter 3 Tests and Diagnostics for more information on how to perform the test program. If any error is detected by the test, go to Procedure 2. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-45 Downloaded from www.Manualslib.com...
LAN harness may be faulty. Replace it with a new one. If the problem still occurs, perform Check 5. Check 5 System board may be faulty. Replace it with a new one following the instruction in Chapter 4. 2-46 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
The connection of sound system is shown in the following figure. As the connection may be defective, disassemble the PC and check each connection. If the problem still occurs, go to Procedure 3. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-47 Downloaded from www.Manualslib.com...
If the problem still occurs, perform Check 5. Check 5 System board may be faulty. Replace it with a new one following the instructions in Chapter 4. 2-48 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Perform the test following the instructions described in Chapter 3. If the computer passes the test, the function is correctly working. If the computer does not pass the test, perform Procedure 2. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-49 Downloaded from www.Manualslib.com...
Bluetooth module. If the Bluetooth antenna cable is not connected properly, connect it firmly and perform Procedure 1. If the problem still occurs, go to the procedure 3. 2-50 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 3. Check3 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-51 Downloaded from www.Manualslib.com...
LAN. Perform the test following the instructions described in Chapter 3. If the computer passes the test, the function is correctly working. If the computer does not pass the test, perform Procedure 2. 2-52 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Make sure the wireless LAN antenna cables (black and white) are firmly connected to the wireless LAN card. If the antenna cables are disconnected, connect them firmly and return to Procedure 1. If there is still an error, go to procedure 3. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-53 Downloaded from www.Manualslib.com...
Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 3. Check 4 System board may be faulty. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. 2-54 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
The SD card may be faulty. Replace it with a new one. If the problem persists, perform Check 3. Check 3 The system board may be faulty. Replace it with a new one. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-55 Downloaded from www.Manualslib.com...
3. Make sure the first joint of your finger is on the sensor. 4. Slide slowly your finger from the first joint to fingertip at constant speed. When not recognized, adjust the speed. Fingerprint Fingerprint sensor sensor 2-56 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 97
4. Click “Create Account” button in the (default) condition that the “Computer administrator” is selected in [Pick an account type]. 5. Select the icon of Account (e.g. “TOSHIBA”) that has been made in item 2 to item 4 in [User Accounts] display.
Page 98
2 Troubleshooting 2.16 Fingerprint sensor 3. Input the name of Account (e.g. “TOSHIBA”), which has been inputted in item 3 in Procedure 1, in the box at the right of [User Name:] on the [Verify Username and Password]. In addition, input the password, which has been inputted in item 7 in Procedure 1, in the box at the right of name (e.g.
Page 99
The message of “Verification Successful” is displayed. Click [Next] button. 7. When [Omnipass Enrollment Wizard] is displayed, you are asked if you want to register one more finger. Click [No]. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-59 Downloaded from www.Manualslib.com...
Page 100
2.16 Fingerprint sensor 8. When [Audio and Taskbar Settings] is displayed, click [Next]. 9. When [Congratulations] is displayed, click [Done]. 10. When [OmniPass-Logon New User?] is displayed, click [Yes]. 2-60 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 101
3. In the Windows Log-ON window, scan the fingerprint of your right index finger. Make sure that scanned fingerprint is displayed on the frame of [Logon Authentication] in green and you can log on. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-61 Downloaded from www.Manualslib.com...
Page 102
2 Troubleshooting 2.16 Fingerprint sensor 4. After starting Windows, Make sure that the name of Account (e.g. “TOSHIBA”), which has been inputted in item 3 in Procedure 1 at the top of [Start]. 5. Open [User Accounts] from [Control Panel]. Select [Delete an Account] in [Change an Account] and delete the account registered for fingerprint authentication.
Page 103
Chapter 3 Tests and Diagnostics [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
3 Tests and Diagnostics 3-ii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 105
NDP Test........................3-32 3.16 Expansion Test......................3-33 3.17 CD-ROM/DVD-ROM Test ..................3-35 3.18 Error Code and Error Status Names................. 3-36 3.19 Hard Disk Test Detail Status..................3-39 PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-iii Downloaded from www.Manualslib.com manuals search engine...
Page 106
Error messages and the contents ............3-67 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program ..........3-69 3.27.1 LAN test ..................... 3-69 3.27.2 Modem test ..................3-72 3.27.3 Bluetooth test..................3-73 3.27.4 IEEE1394 test..................3-83 3-iv [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 107
3.28.3 CD Sound (Standard) test..............3-87 3.28.4 CD Sound (Legacy) test ..............3-89 3.29 SETUP ........................3-90 3.29.1 Function Description ................3-90 3.29.2 Accessing the SETUP Program............3-92 PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 108
Table 3-5 Error message..................... 3-75 Table 3-6 Error code for Bluetooth test (BD_ADDR) ............3-76 Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT)........3-81 3-vi [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
The DIAGNOSTIC TEST MENU contains the following functional tests: SYSTEM TEST MEMORY TEST KEYBOARD TEST DISPLAY TEST FLOPPY DISK TEST PRINTER TEST ASYNC TEST HARD DISK TEST REAL TIMER TEST PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 110
A USB test module (USB test ) A USB cable (USB test) An external CRT monitor (Expansion test) A CD test media TOSHIBA CD-ROM TEST DISK or ABEX TEST CD-ROM (Sound test) A DVD test media (DVD-ROM TEST DISK TSD-1) (Sound test)
The Diagnostics Disk (Main T&D) 3.1.3 Heatrun test program The heatrun test starts automatically after the selection. You will need the following equipment to perform this program. The Diagnostics Disk (Main T&D) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
DMI information and system information from the floppy disk. (3) Execute the subtest0A “Acceleration sensor” in 3.20 ONLY ONE TEST to detect/correct the each axis. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To execute this program, select 1- Repair Main (T&D) in the startup menu, press Enter. The following menu appears. TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC TEST 2 – ONLY ONE TEST...
Page 114
Set the highlight bar to 1, and press Enter. The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST...
Page 115
Use the up and down arrow keys to move the cursor to “ERROR STOP”. Use the right and left arrow keys to move the cursor to the desired option and press Enter. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
3.2.3 Heatrun test program After selecting this test, the heatrun test starts executing the same subtest as 3.23 RUNNING TEST. For more details on this test, refer to the section 3.4. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Flash ROM, press Y, and then Enter. 7. “Create DMIINFO TXT (Y/N) ?” is displayed. Press Y, then the DMI information (text data) is written to the Floppy disk, etc. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 118
This is one of tools to copy the DMI information to a new system board after replacing. This subtest writes all the DMI data in the floppy disk into the new system board. 3-10 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 119
For more details on the system configuration information, refer to “3.25 System configuration”. Subtest 09 E2PROM test (MAC/GUID/DMI) It checks whether the MAC address, GUID of IEEE1394 and DMI information are written. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-11 Downloaded from www.Manualslib.com manuals search engine...
NOTE: The test result (Errorlog.txt) is stored in the floppy disk. The result is displayed in the same format as Log Utilities. For more details of the format, refer to 3.22 Log Utilities. 3-12 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
*** Test Fan Revolution High speed Start Make sure the fan rotates at high speed and the message of fan revolution for it changes. Then press Enter. After a while, the fan rotating will stop. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-15 Downloaded from www.Manualslib.com...
Page 124
: XXXXXX-XXXXX PCN/BND Number : XXXXXXXXXXXX/XXX UUID Number : XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Press [Enter] to EXIT To exit this subtest and return to the SYSTEM test menu, press Enter. 3-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
16KB read buffer and compared the data in the buffers. The read buffer starts from 0001 and the comparison is continued with the following read buffer addresses: 0001, 0003, 0005, 0007, 0009, 000b, 000d and 000f. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-17 Downloaded from www.Manualslib.com...
Appendix D. KEYBOARD TEST IN PROGRESS 302000 Scan code Character code Keytop Ins Lock Caps Lock Num Lock Scroll Lock Ctrl Left Shift Right Shift PRESS [Enter] KEY 3-18 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
This subtest displays bands of gradations for mixed colors, then for red, green, and blue. Next, it displays eight solid colors full screen: red, semi-red, green, semi-green, blue, semi-blue, white and semi-white. Each color displays for three seconds. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-19 Downloaded from www.Manualslib.com...
Page 128
All dot on/off for LCD This subtest displays an all-white screen then an all-black screen. The display changes automatically every three seconds and the screen returns to the DISPLAY TEST menu. 3-20 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 129
The LCD brightness changes in the following order: Super-Bright → Bright → Semi-Bright → Bright → Super-Bright After displaying with Super-Bright of LCD brightness, the screen returns to the DISPLAY TEST menu. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-21 Downloaded from www.Manualslib.com...
01 - Sequential read 02 - Sequential read/write 03 - Random address/data 04 - Write specified address 05 - Read specified address 99 - Exit to DIAGNOSTIC TEST MENU 3-22 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 131
This subtest writes the data specified by an operator to a specified track, head, and address. Subtest 05 Read specified address This subtest reads data from a track, head, and address specified by an operator. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-23 Downloaded from www.Manualslib.com manuals search engine...
Subtest 01 Ripple Pattern This subtest prints characters for codes 20h through 7Eh line-by-line while shifting one character to the left at the beginning of each new line. 3-24 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 133
This subtest checks the output and bi-directional modes of the data control and status lines through the parallel port wraparound connector (34M741986G01). (Both output and bi-directional modes are tested.) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-25 Downloaded from www.Manualslib.com...
NOTE: To execute this subtest, a RS-232C wraparound connector must be connected to the RS-232C port. This subtest checks the data send/receive function through the wraparound connector. 3-26 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
3. The following message appears for whether or not the HDD status is displayed on the screen. The HDC status is described in section 3.20. Select 1 or 2. Detail status display (1:no, 2:yes) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-27 Downloaded from www.Manualslib.com...
Page 136
Subtest 03 Random address/data This subtest writes random data in a random length to random addresses. This data is then read and compared to the original data. 3-28 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 137
This subtest writes specified 2-byte data to all of the cylinders on the HDD. Subtest 09 W-R-C specified address This subtest writes data to a specified cylinder and head on the HDD, then reads the data and compares it to the original data. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-29 Downloaded from www.Manualslib.com...
Writes 1-bit of “off” data (FEh through 7Fh) to address 0Eh through 7Fh Writes the data pattern AAh and 55h to the address 0Eh to 7Fh Then the subtest reads and compares this data with the original data. 3-30 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 139
The real time increments are automatically executed and the following is displayed: Current date : 01-01-2000 Current time : 00:00:00 PRESS [Enter] KEY TO EXIT TEST To exit the test, press Enter. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-31 Downloaded from www.Manualslib.com manuals search engine...
To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 This test checks the following functions of NDP: Control word Status word Addition Multiplication 3-32 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Wait line (40<xx<80) 00005 Other lines (BSY#, BVD1) NN=21, 00 NOTE: Select the subtest number01, The following message will appear: Test slot number select (1:slot0, 2:slot1, 0:slot0&1)? PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-33 Downloaded from www.Manualslib.com manuals search engine...
Page 142
Therefore, make sure only the external display is selected when executing this subtest. 3-34 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE: For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01 or ABEX TEST CD-ROM TCDR-702 and DVD-ROM TEST DISK TSD-1. For the subtest 04, use a CD-RW on the market.
HUB - CLEAR FEATURE1 ERROR HUB - SET FEATURE ERROR(Enab.) HUB - CLEAR FEATURE2 ERROR USB - OVER CURRENT ERROR USB - GET DESCR.ERROR(SECOND) Display VRAM SIZE NOT SUPPORT 3-36 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 146
ILLEGAL LENGTH UNIT ATTENTION MEDIA CHANGE REQUEST MEDIA DETECTED ADDITIMAL SENSE BOUNDARY ERROR CORRECTED DATA ERROR DRIVE NOT READY SEEK ERROR TIME OUT RESET ERROR ADDRESS ERROR 3-38 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
“1” … Correctable data error is corrected. “0” … Not used (Index) “1” … Index is sensed. “0” … Normal (Error) “1” … The previous command was terminated with an error. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-39 Downloaded from www.Manualslib.com manuals search engine...
Page 148
“0” … The hard disk found track 0 during a recalibrate (Track 0) command. “1” … The hard disk could not find track 0 during a recalibrate command. —— Not used 3-40 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
**************************************************************** ..Press test number[1-A, 9] ? Select the subtest number you want to test and press Enter. To return to the DIAGNOSTIC TEST menu, select 9 and press Enter. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-41 Downloaded from www.Manualslib.com...
Page 150
Holding a key down enables the auto-repeat function that causes the key’s display character to blink. Press Del + Enter to end the test. 3-42 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 151
The parameters appear above the <BUTTON> (1) or (2) corresponding to the pressed touch pad switch highlights. To end this subtest, press two touch pad switches at the same time. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-43 Downloaded from www.Manualslib.com...
Page 152
3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 03 GP Button This subtest checks moving of the front operation panel button. Press the Toshiba Presentation button after the following message appears. Press [Toshiba Presentation button] button Power switch Toshiba Presentation Toshiba Assist Press the Toshiba Assist button after the following message appears.
Page 153
NG message appears in the display if an error is found during the test. Confirm the connection of cable, and then execute the test again. Press 9 and Enter to return to ONLY ONE TESST menu. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-45 Downloaded from www.Manualslib.com...
Page 154
If the test ends successfully, the display returns to the ONLY ONE TEST menu. When the display returns to the ONLY ONE TEST menu, remove the slim port replicator from the computer. 3-46 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 155
Check [DC-IN]&[Power]&[Main Battery]LED= Green/Orange Check if the each LED lights in the same color shown in the display (Message switches Green ↔ Orange). Press Enter and return to the ONLY ONE TEST menu. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-47 Downloaded from www.Manualslib.com...
Page 156
PC Card Not Inserted… Press Enter and return to the ONLY ONE TEST menu. CAUTION: PC card wraparound test is not tested on this subtest. 3-48 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 157
The figure below shows the name and position of each side. (heaven surface) Back Right side Front Left side Figure 3-1 Name and positions of each side PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-49 Downloaded from www.Manualslib.com manuals search engine...
Page 158
When any trouble in the above setting is found, the following message appears and the test halts. Then press Enter and return to the Only One Test menu. ** Setting ERROR! ** Press [Enter] key 3-50 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
3. When the message appears, the FDD head cleaning has begun. “cleaning start” 4. The display automatically returns to the DIAGNOSTIC MENU when the program is completed. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-51 Downloaded from www.Manualslib.com manuals search engine...
7. Read data (RD) 8. HDC status (HSTS) 9. Error status name (ERROR STATUS NAME) If the power switch is turned off, the error information will be lost. 3-52 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
The 7 key writes the log information to a floppy disk. 3. In the case of “error retry OK,” a capital “R” will be placed at the beginning of the error status. However, it is not added to the error count. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-53 Downloaded from www.Manualslib.com...
3. After selecting the selectable tests, the running test starts automatically. To terminate the program, press Ctrl + Break. 3-54 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
This program displays the contents of the floppy disk and the designated sectors of the hard disk on the display. 4. HDD ID READ This program reads the hard disk ID and displays hard disk information. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-55 Downloaded from www.Manualslib.com...
After the floppy disk is formatted, the following message will appear. Format complete Another format (1:Yes/2:No) ? (e) Typing 1 displays the message from step (c) above. Typing 2 returns the test to the DIAGNOSTIC MENU. 3-56 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 165
Copy complete Another copy (1:Yes/2:No) ? (g) To copy another disk, type 1 and the message from step (a) is displayed again. Entering 2 returns the test program to the DIAGNOSTIC MENU. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-57 Downloaded from www.Manualslib.com...
Page 166
---Max. address --- [LBA ] = XXXXXXXXX LBA number ???????? (j) Set the LBA number you want to dump. The system will access the disk and dump a list. 3-58 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 167
Selecting HDD ID displays the following HDD ID configuration. [HDD ID Read (VX.XX)] [Drive #1] Model No. = XXXXXXX Press [Enter] key Press Enter to return to the FDD UTILITIES MENU. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-59 Downloaded from www.Manualslib.com manuals search engine...
13. The number of ASYNC ports 14. Math co-processors 15. Floppy Disk Drive [Track/Head/Sector] 16. Hard Disk Drive [Sector/Drive size/Manufacture code] 17. T&D total version 18. Date/Time 3-60 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
CAUTION: Check if Bluetooth or other device other than wireless LAN using 2.4GHz band width is not used nearby. CAUTION: Check that the wireless communication switch is on. 3-62 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Please input the ( s / h / r ) key and push the "Enter" key : Input “r” and press Enter key to execute the Responder T&D for MB5x. The setting is automatically done. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-63 Downloaded from www.Manualslib.com...
: Atheros MB5x Responder mode Please exchange for MB5x Responder media ************************************************************ Please input the ( s / h / r) key and push the "Enter" key : 3-64 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 173
8 : All the tests of MB5x module (Main Antenna Only) (SKU & MAC Check,11b/g communication test) ************************************************************ prompt SELECT TEST No.(1-8) : 3. Input the test number. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-65 Downloaded from www.Manualslib.com manuals search engine...
The number of packets, throughput and RSSI are measured. When they are over the standard, it passes the test. When it passes the test, the following message is displayed. OOOOOO ********************************* KKKK 11b Communication Test : OK OOOOOO ********************************* 3-66 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Error in reading EEPROM data ------------ERROR------------ file bac.txt cannot be opened Expected failure points Failure of wireless LAN module Failure of mounting wireless LAN module Mounting wireless LAN module not specified PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-67 Downloaded from www.Manualslib.com manuals search engine...
Page 176
4. Error in Communication test of 11g mode ************************************** 11g Communication Test : NG !! ************************************** Expected failure points Failure of wireless LAN module Failure of connecting Main/Aux antenna cable or the parts 3-68 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
ICHx GbE (i82540) Diagnostics program ###### ##################################################################### 1 .... (i82562 + ICHx) 2 .... (GbE) ********************************************************************* ..Press test number[1-2] ? Press the number you want to test and press Enter. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-69 Downloaded from www.Manualslib.com manuals search engine...
Page 178
NOTE: The menu displayed by your computer may be slightly different from the one shown above. If a defective is found, NG message will appear in the display. 3-70 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 179
CE Test Complete NOTE: The menu displayed by your computer may be slightly different from the one shown above. If a defective is found, NG message will appear in the display. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-71 Downloaded from www.Manualslib.com...
...Press Key (Y = OK , N =NG) If the color in the LED of the connection checker is orange, press Y, otherwise, press N. 3-72 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
..Press test number [1, 3, T] ? Press 1 or 3 key to perform the corresponding subtest. To quit the Bluetooth test program, eject the floppy disk and turn the computer off while the menu above is displayed. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-73 Downloaded from www.Manualslib.com...
1 to select the test and press Enter. The following message will appear: ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(BD_ADDR) VerX.XX Copyright (C) by TOSHIBA Co. ----------------------------------------------------------------------------- Initializing … When the machine has passed the test, it displays BD_ADDR. If BD_ADDR has no problem, the following message is displayed.
Page 183
3 Tests and Diagnostics If the target machine has any problem, it displays Error message. The following message is displayed. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(BD_ADDR) VerX.XX Copyright (C) by TOSHIBA Co. ----------------------------------------------------------------------------- My BD_ADDR = XXXXXXXXXXXX [h] FFFFFF FFFFFF...
Page 184
SCO Offset Rejected. 0x1c SCO Interval Rejected. 0x1d SCO Air Mode Rejected. 0x1e Invalid LMP Parameters. 0x1f Unspecified Error. ** See the Specification of the Bluetooth System for details. 3-76 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 185
Insert a floppy disk containing the test program into the responder machine and turn on the power. The Bluetooth test menu will appear. Press 3 to select the test and press Enter of the responder machine. The following message will appear: PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-77 Downloaded from www.Manualslib.com...
Page 186
Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co. ----------------------------------------------------------------------------- +----------------------+ BD_ADDR of the DUT = XXXXXXXXXXXXX [h] +----------------------+ Ready>>>>>>>>>>>>>>>>>>>>>> <- Progress Bar [ESC] : Stop 3-78 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 187
M PPPPPP EEEEEE TTTTTTT EEEEEEE DDDDD MM P O M M M M P M PPPPPP EEEEEE EEEEEEE D CCCC LLLLLLL EEEEEE EEEEEEE DDDDD Testing is finished A>_ PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-79 Downloaded from www.Manualslib.com manuals search engine...
Page 188
If any problem is detected during the test, the massage FAIL is displayed on the tester machine with the error code as shown below. The error code begins with the least significant digit. 3-80 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 189
SCO Offset Rejected. 0x1c SCO Interval Rejected. 0x1d SCO Air Mode Rejected. 0x1e Invalid LMP Parameters. 0x1f Unspecified Error. ** See the Specification of the Bluetooth System in detail. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-81 Downloaded from www.Manualslib.com manuals search engine...
Page 190
Not Exist 0x2b Not Exist 0x2c Not Exist 0x2d Not Exist 0x2e Not Exist 0x2f Not Exist ** See the Specification of the Bluetooth System in detail. 3-82 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
This program is executed in the responder machine to initialize the responder machine with the IEEE1394 cable connected to the target machine before executing subtest 01. Subtest03 (1394 GUID Display) This program checks the GUID of IEEE1394. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-83 Downloaded from www.Manualslib.com manuals search engine...
2 .... ( Sine wave ) 3 .... ( Line IN recording & play ) 9 .... Exit to Main *************************************************************** ..Press test number[1-3, 9] ? 3-84 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 193
Build data: XXX XX XXXX at XX:XX:XX Loading “mic.wav”. The message in the display might have slight difference from those above. NOTE: The display returns to the Sound (Standard) test menu after the test ends. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-85 Downloaded from www.Manualslib.com...
The display returns to the Sound (Standard) test menu after the test ends. 3.28.2 Sound (Legacy) test To execute the Sound (Legacy) test, select 2 and press Enter. NOTE: Sound (Legacy) test is not supported in this model. 3-86 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To execute the CD Sound (Standard) test, press 3 and Enter. Insert the test media (TOSHIBA TEST CD-ROM or ABEX TEST CD-ROM) or music CD on the market (if the test media can not be prepared). Following menu appears in the display.
Page 196
This subtest plays sine wave while changing its table from 400Hz to 3KHz and also changing the channel from left speaker to right speaker. The test returns to the CD Sound (Standard) menu after the test ends. 3-88 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
3.28.4 CD Sound (Legacy) test To execute the CD Sound (Legacy) test, select 4 and press Enter. CAUTION: Sound (Legacy) test is not supported in this model. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-89 Downloaded from www.Manualslib.com...
3 Tests and Diagnostics 3.29 SETUP 3.29.2 Accessing the SETUP Program Select 0-SETUP in the Main Menu and press Enter key. The following display appears. 3-92 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 201
2. Press End and then press Y to accept the factory preset settings. NOTE: When you execute the default setting, the following settings are not changed: HDD Mode Password Write Policy in the CPU Cache PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-93 Downloaded from www.Manualslib.com...
Page 202
When you select the battery save mode, the following sub-window will appear. Full Power The following shows full power settings. Low Power The following shows low power settings. 3-94 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 203
Lowers the CPU processing speed first, then if necessary turns on the fan. NOTE: Too hot condition may cause defect on the CPU. When the hot condition continues, the power is automatically turned off in resume mode. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-95 Downloaded from www.Manualslib.com...
Page 204
Sets Master HDD Password and User HDD Password (c) User Password This item sets User password. For details on setting user password, refer to the User’s Manual. 3-96 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 205
NOTE: (*1) FDD is looked for when the boot disk is contained in external FDD. When SD memory card is set as the boot disk, external FDD is looked for first. Next, SD memory card is looked for. (*2) CD-ROM refers to an Optical drive. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-97 Downloaded from www.Manualslib.com...
Page 206
LCD Display Stretch enables or disables a larger display area of the screen. Enabled Enables the LCD display stretch feature. (Default) Disabled Disables the LCD display stretch feature. 3-98 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 207
Wake-up on LAN = Disabled Set the parameters for the Auto Power On (automatic power on) function and the Wake-up on LAN in the “OPTIONS” window. To set the time, use Space PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-99 Downloaded from www.Manualslib.com...
Page 208
All Devices BIOS sets all devices. NOTE: When using installed OS, selecting “Set by OS” is recommended. But, when executing a diagnostic program, select “ All Devices”. 3-100 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 209
When Y, E, S and Enter keys are pressed, the data is disposed. After changing, the display of TPM item is changed to Disabled and this item becomes not displayed and the cursor could not be moved on the TPM item. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-101 Downloaded from www.Manualslib.com...
Page 210
Sets the priority of the USB memory to be equivalent to the FDD. 15. PCI LAN This option enables/disables the Built-in LAN functions. (a) Built-in LAN Enabled Enables Built-in LAN functions. (Default) Disabled Disables Built-in LAN functions. 3-102 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Chart Notation The chart shows the case for the following example: Removing the touch pad. All FRUs of 4.2 Battery from down to 4.6 Keyboard/Bottom cover must be removed PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 218
Please read the following safety instructions before disassembling the computer and always follow the instructions while working on the computer. DANGER: 1) Always use the genuine battery that is authorized by Toshiba or compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode.
Page 219
Screw sizes are noted in the text and figures. 9. As all parts have sharp edges and corners, take care not to cut yourself. 10. After replacing an FRU, check that the computer and replaced part operate correctly. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 220
3. Normal pin connectors are used for all other cables. Simply pull out or push in these connectors to disconnect or reconnect. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 221
Tweezers (for lifting screws) ESD mats (lay on work table or floor) An ESD wrist strap and heel grounder Anti-static carpet or flooring A pair of needle-nose pliers PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 222
NOTE: The computer contains several flat head screws. These screws have less contact area with the screwdriver, so be careful to press firmly enough to prevent the screwdriver from slipping out and damaging the screw head. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 223
B: Bind screw F: Flat head screw S: Super flat head screw T: Tapping screw U: Other screws (Unique screws: pan head, stud, etc.) Example: B6 ... 6mm bind screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Battery latch Battery pack Figure 4-1 Removing the battery pack NOTE: Dispose of the used battery pack in accordance with the laws and ordinances of your local authority. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 225
Dispose always the used battery pack in accordance with the laws and ordinances of your local authority. Use only the batteries approved by Toshiba. NOTE: Check visually the battery terminals and clean off any dirt with a dry cloth.
To install the PC card, follow the steps below and refer to Figure 4-2. 1. Make sure the eject button do not stick out. 2. Insert the PC card and press it until it is securely connected. 4-10 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Installing the SD card To install the SD card, follow the steps below and refer to Figure 4-3. 1. Insert the SD card and press it until it is securely connected. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-11 Downloaded from www.Manualslib.com...
2. Loosen the screw (with e-ring) and remove the memory slot cover. 3. Press the two latches outward and remove the memory module. Screw (e-ring) Latch Memory slot cover Latch Memory module Figure 4-4 Removing the memory module 4-12 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 229
3. When the power of the computer is turned on, the computer checks automatically the memory size. Confirm that the new memory is detected correctly. 4. If the memory is not detected, check that it is connected correctly. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-13 Downloaded from www.Manualslib.com...
1. Remove the following screw and HDD slot cover. • M2×3S S-FLAT HEAD screw M2×3S S-FLAT HEAD HDD slot cover Figure 4-5 Removing the HDD slot cover 4-14 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 231
Figure 4-6 Removing the HDD assembly 3. Peel off two gaskets from the HDD unit and detach the HDD from the HDD holder. Gasket HDD holder Figure 4-7 Removing the HDD PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-15 Downloaded from www.Manualslib.com...
Page 232
CAUTION: When installing the HDD slot cover, be sure to insert the HDD slot cover into the HDD slot slantingly and insert the projection into the hole. Projection 4-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
5. Lift the upper side of the keyboard and turn it face down on the palm rest. Keyboard holder M2×2.5C S-FLAT HEAD Keyboard M2×2.5C S-FLAT HEAD M2×4S BIND Figure 4-8 Removing the keyboard holder PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-17 Downloaded from www.Manualslib.com manuals search engine...
Page 234
5. Install the keyboard holder while engaging the latches. 6. Close the display and turn the computer face down. 7. Secure the keyboard holder with the following screw. • M2×4S BIND screw 4-18 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
5. Remove the following screw and the switch board. • M2×2.5C S-FLAT HEAD screw Switch cover M2×2.5C S-FLAT HEAD M2×8S BIND Switch board CN3270 Switch cable Figure 4-10 Removing the switch board PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-19 Downloaded from www.Manualslib.com manuals search engine...
Page 236
M2×2.5C S-FLAT HEAD screw 3. Install the switch cover. 4. Turn over the computer and secure the switch cover with the following screw. • M2×8S BIND screw 4-20 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To remove the touch pad, follow the steps below and refer to Figure 4-11 and 4-12. 1. Remove the touch pad cover while releasing the latches. Touch pad cover Figure 4-11 Removing the touch pad cover PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-21 Downloaded from www.Manualslib.com...
Page 238
5. Disconnect the touch pad cable from the connector on the touch pad assembly. M2×3C S-FLAT HEAD Touch pad cable CN3240 Touch pad assembly Figure 4-12 Removing the touch pad 4-22 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 239
• M2×3C S-FLAT HEAD screw 3. Connect the touch pad cable to the connector CN3240 on the system board. 4. Install the touch pad cover while engaging the latches. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-23 Downloaded from www.Manualslib.com manuals search engine...
• M2×4S BIND screw x13 (“4” in the figure below) • M2×3S S-FLAT HEAD screw x1 (“3” in the figure below) Figure 4-13 Removing the cover assembly(1) 4-24 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 241
S-FLAT HEAD screw 4. Remove the cover assembly by lifting it up from the base assembly. M2×4B S-FLAT HEAD Cover assembly Figure 4-14 Removing the cover assembly(2) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-25 Downloaded from www.Manualslib.com manuals search engine...
Page 242
3. Turn over the computer and secure the following screws. • M2×4S BIND screw x13 (“4” in the figure 4-13) • M2×3S S-FLAT HEAD screw x1 (“3” in the figure 4-13) 4-26 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
2. Connect the Bluetooth flat cable to both the Bluetooth module and the connector CN4400 on the system board. 3. Install the Bluetooth module along the guide and secure it with the following screw. • M2×3C S-FLAT HEAD screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-27 Downloaded from www.Manualslib.com manuals search engine...
4. Disconnect the SP FPC from the connector CN6170 on the system board and connector CN950 on the fingerprint sensor board to remove. M2×3C S-FLAT HEAD Speaker CN950 SP FPC Speaker holder CN6170 Figure 4-17 Removing the speaker/SP FPC 4-28 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 245
5. Connect the speaker cable to the connector CN7 on the SP FPC. 6. Fix the SP FPC with the following screws. • M2×3C S-FLAT HEAD screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-29 Downloaded from www.Manualslib.com manuals search engine...
1. Connect the MDC cable to the MDC board. 2. Install the MDC board to the connector CN3010 on the MP FPC and secure it with the following screws. • M2×3C S-FLAT HEAD screw 4-30 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To install the RTC battery, follow the steps below and refer to Figure 4-20. 1. Install the RTC battery to the RTC battery slot and connect the RTC battery cable to the connector CN9990 on the system board. 2. Stick the two glass tapes. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-31 Downloaded from www.Manualslib.com...
2. Gently push the Wireless LAN card down until the latches on both sides are engaged. 3. Connect the wireless LAN antenna cables (black and white) to the connectors on the Wireless LAN card. 4-32 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
1. Install the fan and secure it with the following screws. • M2×4C BIND screw 2. Connect the fan cable to the connector CN8770 on the system board and stick the glass tape. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-33 Downloaded from www.Manualslib.com manuals search engine...
CN9500 on the system board. • M2×3C S-FLAT HEAD screw Kill switch holder M2×3C S-FLAT HEAD M2×3C S-FLAT HEAD MP FPC CN9500 Figure 4-23 Removing the MP FPC 4-34 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 251
• M2×3C S-FLAT HEAD screw 2. Install the kill switch holder and secure it with the following screw. • M2×3C S-FLAT HEAD screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-35 Downloaded from www.Manualslib.com manuals search engine...
To install the HD FPC, follow the steps below and refer to Figure 4-24. 1. Connect the HD FPC to the connector CN1800 on the system board and secure it with the glass tape. 4-36 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To install the PC card slot, follow the steps below and refer to Figure 4-25. 1. Connect the PC card slot to the connector CN2110 on the system board and secure it with the following screws. • M2×4C S-FLAT HEAD screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-37 Downloaded from www.Manualslib.com manuals search engine...
To install the LAN/Modem jack, follow the steps below and refer to Figure 4-26. 1. Install the LAN/Modem jack to the slot. 2. Connect the LAN cable to the connector CN4100 on the system board. 4-38 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
2. Disconnect the LED cable from the connector CN3260 on the system board (front). 3. Remove the following screws and system board. • M2×3C S-FLAT HEAD screw 4. Remove the audio cover. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-39 Downloaded from www.Manualslib.com manuals search engine...
Page 256
3. Connect the LED cable to the connector CN3260 on the system board (front). 4. Connect the LCD cable and FL cable to the connectors CN5600 and CN5601 on the system board. 4-40 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
To install the internal microphone, follow the steps below and refer to Figure 4-28. 1. Install the internal microphone to the microphone holder. 2. Connect the microphone cable to the connector CN6050 on the system board. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-41 Downloaded from www.Manualslib.com...
To install the LED FPC, follow the steps below and refer to Figure 4-29. 1. Install the LED FPC according to the guide and secure it with the following screws. • M2×3C S-FLAT HEAD screw 4-42 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
(“3.2” in the figure below) • M2.5×4S FLAT HEAD screw x2 (“4” in the figure below) 2. Remove the display mask while releasing the latches. Figure 4-30 Removing the display mask PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-43 Downloaded from www.Manualslib.com manuals search engine...
Page 260
(“3.2” in the figure 4-30) • M2.5×4S FLAT HEAD screw x2 (“4” in the figure 4-30) 3. Stick the six mask seals and four LCD cushions to the display mask. 4-44 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
2. Peel the insulator and disconnect the two cables from the both sides of the connector on the FL inverter. 3. Remove the FL inverter. M2×3C S-FLAT HEAD FL inverter Insulator Figure 4-31 Removing the FL inverter PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-45 Downloaded from www.Manualslib.com manuals search engine...
Page 262
4. Carefully lift up the top of the LCD unit and peel off the glass tape. 5. Disconnect the LCD cable and remove the LCD unit. LCD unit LCD cable Glass tape Figure 4-32 Removing the LCD unit 4-46 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 263
3. Connect the two cables to the both sides of the connector on the FL inverter and install the FL inverter according to the guide. 4. Secure the FL inverter with the following screw and stick the insulator. • M2×3C S-FLAT HEAD screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-47 Downloaded from www.Manualslib.com manuals search engine...
1. Remove the following screws (back) and hinge caps (left and right). • M2×3C S-FLAT HEAD screw M2×3C S-FLAT HEAD Hinge cap Hinge cap M2×3C S-FLAT HEAD Figure 4-33 Removing the hinge cap 4-48 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 265
2. Remove the following screws (back) and palm rest. • M2.5×4B FLAT HEAD screw Palm rest M2.5×4B FLAT HEAD M2.5×4B FLAT HEAD Figure 4-34 Removing the palm rest PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-49 Downloaded from www.Manualslib.com manuals search engine...
Page 266
M3×3S BIND screw • M2×4B S-FLAT HEAD screw M3×3S BIND M2×4B S-FLAT HEAD Hinge Hinge M2×4B S-FLAT HEAD M3×3S BIND LCD cable Figure 4-35 Removing the hinge 4-50 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 267
3. Install the palm rest and secure it with the following screws (back). • M2.5×4B FLAT HEAD screw 4. Install the both sides’ hinge caps and secure them with the following screws (back). • M2×3C S-FLAT HEAD screw PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-51 Downloaded from www.Manualslib.com manuals search engine...
1. Stick the wireless LAN antenna on the display cover in place. 2. Set the wireless LAN antenna cables on the display cover in place. 3. Secure the wireless LAN antenna cables with the six acetate tapes. 4-52 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
1. Stick the Bluetooth antenna on the display cover in place. 2. Set the Bluetooth antenna cable on the display cover in place. 3. Secure the Bluetooth antenna cable with the five acetate tapes. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-53 Downloaded from www.Manualslib.com...
- Be careful not to soil or deform the lamp reflector. - Make sure that the power of the LCD module is turned off before connecting or disconnecting cables and connectors. 4-54 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 271
TAB and PCB. Tape of the bezel side Insulator sheet Production label Insulation sheet, double-adhesive tape Figure 4-38 Replacing TMD fluorescent lamp(1) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-55 Downloaded from www.Manualslib.com manuals search engine...
Page 272
2) Remove the left side screw and right side screw as shown in the figure below. CAUTION: Use a Philips screwdriver with type 0 bit to remove the screws. Production label Figure 4-39 Replacing TMD fluorescent lamp(2) 4-56 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 273
Peel off the double-adhesive tape slowly. Double adhesive tape within the bezel. Release two bezel latches. Release three bezel latches. Peel off the double- adhesive tape slowly. 4-40 Replacing TMD fluorescent lamp(3) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-57 Downloaded from www.Manualslib.com manuals search engine...
Page 274
1) Open the PCB to the horizontal position as shown in the figure below. CAUTION: Be careful not to damage the TAB. Figure 4-41 Replacing TMD fluorescent lamp(4) 4-58 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 275
1) Remove the cell with the PCB from the backlight unit as shown in the figure below. CAUTION: 1) Peel off the cell carefully not to break it. 2) Be careful not to damage the TAB. Cell Figure 4-42 Replacing Toshiba fluorescent lamp(5) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-59 Downloaded from www.Manualslib.com...
Page 276
1) Check the items shown in the Figure below. Do not let the Do not let the sheet out of sheet out of the the frame. frame. Figure 4-43 Replacing TMD fluorescent lamp(6) 4-60 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 277
Next, install the cell with the PCB to the backlight unit. CAUTION: 1) Install by aligning the left under corner as shown below. 2) Be careful not to damage the FPC. Cell with PCB Figure4-44 Replacing TMD lamp(7) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-61 Downloaded from www.Manualslib.com...
Page 278
1) Fold the TAB (PCB) around the back of the backlight unit as shown in the figure below. CAUTION: 1) Be careful not to damage the TAB. Figure 4-45 Replacing TMD lamp(8) 4-62 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 279
Engage three latches of the bezel. Stick double-adhesive tape of the backside bezel. Bezel set: Push against the left under of the frame Figure 4-46 Replacing TMD fluorescent lamp(9) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-63 Downloaded from www.Manualslib.com manuals search engine...
Page 280
2) When sticking the insulation sheet, be careful not to damage the PCB, cell and B/L. Production sheet Stick the double-adhesive tape of the insulation sheet to the edge of the PCB. Figure 4-47 Replacing TMD lamp(10) 4-64 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
LCD cover before securing the module with screws. Do not force the module into place, because stress can affect its performance. Also, the panel’s polarized surface is easily scarred, so be careful when handling it. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 290
4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com...
Page 291
6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 292
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 293
10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 294
Appendices Appendix A Handling the LCD Module [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Appendix B Board Layout Appendices Apx. B Appendix B Board Layout B.1 System board Front View Figure B-1 System board layout (front) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 296
CN3260 LED Board Connector CN3270 SW & LED I/F CN9800 Not used CN3200 Keyboard Connector CN3240 Touch-pad Connector CN3400 Debugging port IC2000 PC Card Controller IC3200 EC/KBC IC3000 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
KBRT07-S3N KBSC14-S3N KBSC15-S3N N.C. N.C. CN3240 PAD I/F connector (8pin) Table C-7 PAD I/F connector r (8pin) Pin No. Signal name Pin No. Signal name IPDDAT-P5P IPDCLK N.C. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
BTMDL-P3N N.C. C.11 CN4610 USB Port 0 connector (4pin) Table C-11 USB Port 0 connector (4pin) Pin No. Signal name Pin No. Signal Name USBOPS-E5V USBP0-S3N USBP0-S3P PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] C-11 Downloaded from www.Manualslib.com manuals search engine...
FS Board C.32 CN950 SP FPC I/F Connector (6pin) Table C- 32 SP FPC I/F Connector (6pin) Pin No. Signal name Pin No. Signal name USBFS-S3P USBFS-S3N FGSPON-S3N PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] C-25 Downloaded from www.Manualslib.com manuals search engine...
Page 328
Appendices Appendix C Pin Assignment C-26 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 329
Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Note Keytop Make Break Make Break ‘ ~ 7 & BkSp PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 330
Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 331
Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Ctrl Alt (L) Space ALT (R) ← Home ↑ ↓ PgUp PgDn → PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
With right Shift Set 1 E0 AA __________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12 ________ E0 F0 59 E0 12 ___________ E0 59 PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 334
↑ ↓ PgUp PgDn → Table D-4 Scan codes with Fn key Code set 1 Code set 2 Keytop Make Break Make Break CTRL LALT ARROW NUMERIC Scrl [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Page 335
Break (–) Table D-6 No.124 key scan code Shift Code set 1 Code set 2 Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 336
Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
(Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts. 6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 342
Appendices Appendix G BIOS rewrite procedures [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
5. Turn on the power while holding down the Tab key. (Keep holding down the key until a message appears on the screen.) The BIOS/EC/KBC rewriting starts. 6. When the EC/KBC rewrite is completed, the system is automatically turned off. PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com...
Page 344
Appendices Appendix H EC/KBC rewrite procedures [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...
Appendix I Reliability Appendices Apx. I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table I-1 MTBF Component Time (hours) System 5,789 PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] Downloaded from www.Manualslib.com manuals search engine...
Page 346
Appendices Appendix I Reliability [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Downloaded from www.Manualslib.com manuals search engine...