Control Connections - WEG CFW-11 Installation Manual

CONTROL CONNECTIONS

The control connections (analog inputs/outputs, digital inputs/
outputs), must be made at the CC11 control board terminal strip XC1.
XC1
Terminal Strip
CW
1 REF+
2 AI1+
≥5 kΩ
3 AI1-
4 REF-
CCW
5 AI2+
6 AI2-
rpm
7 AO1
AGND
8
(24 V)
amp 9 AO2
AGND
10
(24 V)
11 DGND*
12 COM
13 24 Vdc
14 COM
15 DI1
16 DI2
17 DI3
18 DI4
19 DI5
20 DI6
21 NC1
22 C1
23 NO1
24 NC2
25 C2
26 NO2
27 NC3
28 C3
29 NO3
Figure 21: Signals at connector XC1 - digital inputs working as
"Active High"
NOTE!
For changing to "Active Low" remove the jumpers
between XC1:11 and 12, place this jumper between
XC1:12 and 13 and connect common points of the
switches on DI1 to DI6 to XC1:11, instead of XC1:13.
Factory Setting Function
Positive reference for
potentiometer (5.4 V ± 5 %).
Analog input # 1:
Speed reference (remote).
Negative reference for
potentiometer (-4.7 V ± 5 %).
Analog input # 2:
No function.
Analog output # 1:
Speed.
Reference (0 V) for the analog
outputs.
Analog output # 2:
Motor current.
Reference (0 V) for the analog
outputs.
Reference (0 V) for the 24 Vdc
power supply.
Common point of the digital
inputs.
24 Vdc power supply.
Common point of the digital
inputs.
Digital input # 1:
Start / Stop.
Digital input # 2:
Direction of rotation (remote).
Digital input # 3:
No function.
Digital input # 4:
No function.
Digital input # 5:
Jog (remote).
Digital input # 6:
2 nd ramp.
Digital output #1 DO1 (RL1):
No fault.
Digital output #2 DO2 (RL2):
N > N - Speed > P0288.
X
Digital output #3 DO3 (RL3):
N* > N - Speed reference >
X
P0288.
ON
1 2 3 4
1
XC1
29
Factory Default DIP-
Signal
Function switch
Speed Reference OFF: 0 to 10 V (factory setting)
AI1 S1.4
(remote) ON: 4 to 20 mA / 0 to 20 mA
OFF: 0 to ±10 V (factory setting)
AI2 No Function S1.3
ON: 4 to 20 mA / 0 to 20 mA
OFF: 4 to 20 mA / 0 to 20 mA
AO1 Speed S1.1
ON: 0 to 10 V (factory setting)
OFF: 4 to 20 mA / 0 to 20 mA
AO2 Motor Current S1.2
ON: 0 to 10 V (factory setting)
Figure 22: DIP Switches for setting signal type on analog inputs and
outputs
NOTE!
For information of Safety Stop (STO) function refer
to Installation, Configuration and Operation guide.
Installation Guide
Slot 5
Slot 1 (white)
Slot 2 (yellow)
Slot 3 (green)
Slot 4
Factory
Selection
Setting
OFF
OFF
ON
ON
CFW-11 | 13