Table of Contents
Advertisement
INSTALLATION GUIDE
DB3
2016 Dodge/Ram 1500 - 403.CHRYSLER6 2.04 RXT
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
Advertisement
Table of Contents
Related Manuals for Directed Electronics DB3
Summary of Contents for Directed Electronics DB3
- Page 1 INSTALLATION GUIDE 2016 Dodge/Ram 1500 - 403.CHRYSLER6 2.04 RXT Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
-
Page 2: Table Of Contents
Contents Introduction Pre-installation and application warnings Installation Wiring diagram Vehicle connections SmartStart/XL202 installation notes Connecting the module Module programming LED diagnostics and troubleshooting Soft reset Hard reset Feature programming Feature and option list Limited one year consumer warranty Quick reference guide... - Page 3 Warning! Safety first The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.
-
Page 4: Introduction
Introduction DB3 is an all-in-one door lock and override module. This guide supports the installation of a DB3 in Range Extender Ready (RXT) mode with an RF System or a SmartStart (both sold separately). Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness THCHD3 Keys required for Keys required for compatible programming operation... - Page 6 T-Harness (THCHD3) Wiring diagram with OBDII Diagnostic 16-pin Connector (vehicle side) These T-Harness connectors are NOT interchangeable. They will fit ONLY the appropriate vehicles. OBDII T-01 THCHD3 Rev. 1 T-02 6-pin Black 6-pin White (Optional T-Harness) Connectors Connectors NOT Used Remote Start Safety Override Switch N/C: Yellow/Red...
-
Page 7: Wiring Diagram
Wiring diagram (-) Ground, pin 4 CAN C High: Gray/White, pin 6, CAN IHS High: Gray, pin 3 OBDII Diagnostic Connector You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the HS CAN High: Tan/Black: 3 SmartStart/XL202 Installation Notes for HS CAN Low: Tan: 4... -
Page 8: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2016 Dodge/Ram 1500. Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Ref. - Page 9 Input 10-pin black connector (H3) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Ref. H3/1 Black/White No Connection No Connection H3/2 Green/Black No Connection No Connection H3/3 Green/White No Connection No Connection H3/4 Red/Black No Connection No Connection H3/5 Violet/White No Connection...
-
Page 10: Smartstart/Xl202 Installation Notes
SmartStart/XL202 installation notes The DB3 Range Extender Ready (RXT) solution offers two (2) configuration options to control your system: RF System or SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202. SmartStart revision A SmartStart is optional and not included. It MUST be purchased separately. -
Page 11: Connecting The Module
Note: Before connecting either the XL202 or SmartStart module to DB3, it is important to ensure that the proper feature and function programming is selected using DirectLink (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application. -
Page 12: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Connect the 10-pin, 12-pin and 14-pin harnesses to DB3, then wait until the LED turns ON solid red. Press 5 times on the programming button. The LED flashes orange. -
Page 13: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power. - Page 14 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence. received. Flashes green Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes red &...
-
Page 15: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module programming”. The firmware and settings flashed to the module will not be affected. Connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module. (12-pin) (Button) (10-pin) -
Page 16: Hard Reset
Hard reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default factory settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. Refer to “Feature and option list”. Connect the 10-pin &... -
Page 17: Feature Programming
Feature programming To enter feature programming routine: 1. Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the Programming button. 4. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g. -
Page 18: Feature And Option List
Feature and option list It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. -
Page 19: Limited One Year Consumer Warranty
Limited one year consumer warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under... -
Page 20: Chrysler6 2.04 2016 Dodge/Ram
Range Extender Ready (RXT) List of Available Commands Range Extender Ready (RXT) is used to amplify the distance covered Note that the information below is for Viper, Clifford and Python models. Icons and by factory remote starters, which are built into the BCM of the vehicle. commands may differ depending on the remote brand and model purchased. - Page 21 SmartStart Compatible Notes This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone;...