Table of Contents
Advertisement
INSTALLATION GUIDE
DB3
2010 Toyota Camry (Smart Key) - 403.TL1 5.02
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
Advertisement
Table of Contents
Related Manuals for Directed Electronics DB3
Summary of Contents for Directed Electronics DB3
- Page 1 INSTALLATION GUIDE 2010 Toyota Camry (Smart Key) - 403.TL1 5.02 Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
-
Page 2: Table Of Contents
Contents Introduction Pre-installation and application warnings Key type OEM remote starter detection Wiring diagram with T-Harness (TLTH1 & THTOD1) Vehicle connections Connecting the module Module programming LED diagnostics and troubleshooting Soft reset Hard reset Feature programming Feature and option list Limited one year consumer warranty Quick reference guide... - Page 3 Warning! Safety first The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.
-
Page 4: Introduction
Introduction DB3 is an all-in-one door lock and override module. Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to “Connecting the module” for more information. This solution is compatible with the 2010 Toyota Camry (Smart Key) and offers the following features: •... -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness TLTH1/THTOD1 Keys required for Keys required for compatible programming operation... -
Page 6: Key Type
Key type Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings. An “H” means the vehicle is compatible with TL10. A “G” means the vehicle is compatible with Tl5 and TL7. A dot means the vehicle is compatible with TL1. -
Page 7: Oem Remote Starter Detection
OEM remote starter detection How to know if the vehicle is equipped with an OEM remote starter An “ENGINE STARTER” 2- Remote start the OEM remote starter: sticker should be on the Press the remote control’s lock button twice within 2 seconds, remote. - Page 8 Platform: DBALL2 Firmware: TL1 Rev.: 20170215 Wiring diagram with TLTH1/THTOD1 T-Harness D o n o t c o n n e c t a n y o t h e r (-) Hood Status Input accessory, ignition or starter wires (+) Brake Input from the remote starter to the (AC) Tach Input...
-
Page 9: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2010 Toyota Camry (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Ref. - Page 10 Input 10-pin black connector (H3) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Ref. H3/1 Green (-) W2W Only - Lock Input Remote Starter H3/2 Blue (-) W2W Only - Unlock Input Remote Starter H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter H3/4 White/Violet...
-
Page 11: Connecting The Module
Connecting the module Important! Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior to moving onto programming. Warning! To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application. Flashing a module using your computer: 1. -
Page 12: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Key-typevehicles with CAN Wait until the LED turns ON solid red. Insert the key in the ignition switch. The LED flashes red slowly for a few seconds to indicate the key is in learning mode. - Page 13 * If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to "LED Diagnostics & Troubleshooting" for more information. Press the programming button 5 times to skip the CAN programming. The LED will turn OFF quickly, and it will then turn ON solid orange 3 seconds.
-
Page 14: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power. - Page 15 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence. received. Flashes green Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes red &...
-
Page 16: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module programming”. The firmware and settings flashed to the module will not be affected. D2D installation Connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness. -
Page 17: Hard Reset
Hard reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default factory settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. Refer to “Feature and option list”. D2D installation Connect the 10-pin, 12-pin &... -
Page 18: Feature Programming
Feature programming To enter feature programming routine: 1. Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the Programming button. 4. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g. -
Page 19: Feature And Option List
Feature and option list It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. -
Page 20: Limited One Year Consumer Warranty
Limited one year consumer warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under... -
Page 21: Quick Reference Guide
Quick Reference Guide Vehicle Takeover for Push-To-Start vehicles Notes Note: Takeover feature is not available on Push-to-start vehicles. The engine will stop when a door is opened. List of Available Commands Button(s) Actions Press & hold for 1 second to lock. Press &...