Trainer Mode; Teacher - GRAUPNER MX-10 HOTT Programming Manual

Trainer Mode

Connecting two transmitters for trainer mode operations
The mx-10 HoTT transmitter can be combined by wi-
reless means to form a Trainer system. Here, the second
transmitter must not be the mx-10 HoTT also, every
other HoTT transmitter with the possibility of wireless
Trainer operation is suitable. Therefore please read the
manual of your HoTT system!
Switching from the normal operating mode to the trans-
mitters teacher or student mode is done by the mode
switch on the left top side of the transmitter:
Mode normal
©

teacher

ª
pupil
To change the mode, move the mode switch on the
transmitter in the desired position, press and hold the
BIND-button and then switch on the transmitter.
To display the selected mode ...
LED Status Buzzer Description
orange LED - Transmitter mode
on „normal", country
setting: general
orange LED beeping Transmitter mode:
fl ashes twice after pupil
switching on
orange LED 2x beeping Transmitter mode:
fl ashes twice twice after teacher
switching on
See LED and buzzer signals on page 88.
Important Note:
The following description is based on the time of
printing this manual current version 1.00 of the
transmitter software, and is equally valid for all
previous Software versions. It can not be excluded
that after the next update, the following description
will not be correspondend with the functionality of
the HoTT Trainer system.
Teacher transmitter settings mx-10 HoTT
The trainer model must be programmed completely,
i. e. with all its functions including trims and any mixer
functions in the mx-10 HoTT Teacher transmitter. This
means that it must be possible to control the trainer
model fully, without restriction, by the Teacher trans-
mitter. But, at the conclusion of these preparations,
the trainer model must be bound to the Pupil trans-
mitter. A detailed description of the binding process can
be found on page 106 and 109.
Note when using the mx-10 HoTT as pupil transmitter:
the mx-10 HoTT binding procedure can only be done
in „normal" mode. Before using the transmitter in Pupil
mode, bind the receiver in mode „normal", then switch to
the mode „pupil". In addition, no mixer may be activated,
move the jumper in the middle position „NO MIX", see
also page 105.
All fi ve transmitter control functions of the Teacher trans-
mitter "T" can be transferred to the pupil transmitter "P".
The stick mode of the pupils transmitter may deviate
from the teacher transmitter, because the stick mode
and mixers will be transfered from the teachers transmit-
ter. Therefore the teachers transmitter must be properly
programmed for the training model with all functions and
mixers.
After the pupils transmitter is bound to the trainer model,
set the mx-10 HoTT in the teacher mode. To change
the mode, move the mode switch on the transmitter in
the „teacher" position, press and hold the BIND-button
and then switch on the transmitter.
Now press the BIND-button of the puplis transmitter:
mx-10 HoTT: press and hold
In the following the student programming for the mx-
12/16/20 HoTT is described. Please read also the
instructions for your remote control system!
Switch on the transmitter, and use the arrow buttons of
the left or right-hand four-way button to leaf through on
both transmitters to the "Trainer" menu point of the multi-
function menu. (The trainer model's receiving system,
previously bound to the Pupil transmitter, does not need
to be switched on during the following procedure.):
ser vo set. contr set.
D/R expo phase trim
wing mixer free mixer
ser vo disp basic sett
fail-safe telemetr y
teach/pupi info disp
Press the central SET button of the right-hand four-way
button to open the following menu point:
TRAINER/Pupil
–P
T
1 2 3 4 5 6
SW: ––– BIND:
The illustration above shows the initial state of this
Program description: Trainer system
N/A
127