Specifications - Yamaha CS1D Service Manual

SPECIFICATIONS

Number of scene memories 990
Sampling Frequency Intermal: 48 kHz/44.1 kHz
External: 44.1 kHz -10 %–48 kHz +6 %
Fader 64 x 100 mm motorized
Total Harmonic Less than 0.02 % 20 Hz–20 kHz @
+24 dB into 600 Ω
Distortion Less than 0.007 % 1kHz @ +24 dB
into 600 Ω
CH IN to STEREO OUT
AD converter 28 bit 128 times over sampling
(Signal Delay 1.5 msec @ Fs=48 kHz)
DA converter 27 bit 128 times over sampling
(Signal Delay 1.2 msec @ Fs=48 kHZ)
Frequency Response +1, -2 db 20 Hz–20 kHz @ +10 db
into 600 Ω
Dynamic Range 120 dB typ. AD+DA ("LMY-" AD card
(maximum level to noise level)
Hum & Noise -128 dB typ. Equivalent Input Noise.
(20 Hz–20 kHz)
(Rs=150 W)
(Input Gain=Max.)
InputSection CH1–96, ST IN1–8
De-emphasis/DC cut
Phase
Patch Input, Direct out
(pre eq/pre fader/post fader/post on),
Insert in/out (pre eq/post eq/pre
comp/pre delay/pre fader)
Attenuation -96–0 dB ( dB step)
High pass filter 20 Hz–600 Hz (60 point) slope -6 dB /
-12 dB / -18 dB/oct
Equalizer 4 band PEQ
(Low/shelving, Low-mid, High-mid,
High/Shelving/LPF)
F:
Gain: + -18 dB (0.5 step),
Q:
Gate Gate/Ducking selectable 4 key-n bus
Comp Comp/Expander/compander
selectable 4 key-in bus
Delay Delay time (0–250 ms, 0.02 msec step)
Fader 100 mm motorized, -∞, -90– +10 dB
(128 step/100 mm),
Interpolation 24bit (16,777,216 steps)
On/Off
Cue/Solo On/Off (PFL/AFL)
Pna 127 positions (L=1–63, center, R=1–63)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT.
The wires in this main lead are coloured in
accordance with the following code:
BLUE:
BROWN: LIVE
As the colours of the wires in the main lead of this apparatus may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The BLUE wire must be connected to the terminal that is marked with
the letter N (or coloured BLACK).
The BROWN wire must be connected to the terminal that is marked
with the letter L (or coloured RED).
Be certain that neither core is connected to the earth terminal of the
three pin plug.
to DA card)
Normal/Reverse
20 Hz–20 kHZ (120 point),
0.1–10 (41 point)
NEUTRAL
Stereo/group assign STEREO/MIX 1–48 (FIX/VARI
selectable)
Metering pre att peak, comp/gate gain reduction,
pre att/pre gate/pre fader/post fader/
post on selectable with Peak-Hold
Output section STEREO A, B, MIX 1–48, MATRIX 1–24
Patch Output, Insert in/out
Equalizer 6 band PEQ
(Sub Low/HPF/Shelving, Low, Low-mid,
Mid, High-mid, High/LPF/Shelving)
(Bypass switch for each band)
(Parameters are same as input EQ)
Comp Comp/Expander/compander selectable,
4 key-in bus
Delay Delay time (0–1000 ms, 0.02 msec step)
On/Off
Cue/Solo On/Off (PFL/AFL)
Balance Stereo A, B, Paired Mix & Matrix
Mono Stereo B
to stereo assign from Mix output
to matrix assign from Mix 1–48/stereo A, B
Metering comp gain reduction, pre eq/pre fader/post
fader/ post on selectable with Peak-Hold
Dither On/Off, Word length 16–24 bit (DIO8 only)
Other mixer section
Effects Internal patchable eight multi-effects
units
Graphic equalizer Internal patchable twenty four 31-
band graphic equalizers, each with 4
notch filters
Oscillator sine/pink/burst noise
Talk back From console 1 & 2
Communication In Including ducking control
12 DCA with DCA mute, DCA cue/solo, 9–12
are selectable for output
12 Direct Memory Recall/Mute Group
Monitor A 2tr in 1, 2, ST A, B, user define
selectable with delay (max 750 msec)
Monitor B 2tr in 1, 2, ST A, B, moni A, user
define selectable
2tr in 1–6 1 & 2: Analog/Coaxial/AES/EBU
selectable,
3–6:
(with Sampling Rate Converter for
digital input)
CS1D
AES/EBU
3-1