Yamaha CS1D Service Manual page 130

CS1D
11. CS1D Communication Test
This test checks communications for the BIF1, 2, CCAS boards etc.
11. CS1D-Communication OK
* ETHER (EIF [A])
OK
CH1
CH2
* ETHER (EIF [B])
OK
CH1
CH2
* ETHER (CCAS)
OK
CH1
CH2
* RS232C
OK
* USB
OK
12. CS1D-MIO Test
This test checks the MIO board. It checks the items
below.
Here it is assumed that the elements around the DSP
on the MTCPU board and the CIO board are
operating normally. If this can not be assumed and
an NG appears for these items, it is necessary to
consider the possibility of abnormality in the MIO
board, the CIO board, and the MTCPU board.
The detailed screen output specifications are given
on the following pages.
* There are the following restrictions on the
combination of TO CONSOLE terminal
(inspection reference terminal) and ENGINE
terminal (inspected terminal).
TO CONSOLE 1 – ENGINE A1 or ENGINE A2
TO CONSOLE 2 – ENGINE B1 or ENGINE B2
12-1.CS1D-MIO (Engine A1) Test
This test checks the MIO (Engine A1 port).
12-1. CS1D-MIO (ENGINE A1)OK
* SI/SO
OK
* W.CLK
OK
* ID
OK
In
Out
* MSB/LSB
OK
* 2CH/4CH
OK
121
11. CS1D-Communication
ETHER (EIF [A]):
ETHER (EIF [B]):
ETHER (CCAS):
RS232C:
USB:
When the pop-up box asking you to make the connections
for the USB check appears, connect the USB cable.
(If you connect the cable before requested, the software is
not loaded properly.)
(The USB check driver must be installed before hand.)
Connect USBport [HostPCtoCS1D]. Push OK button.
OK
12-1. CS1D-MIO (ENGINE A1)
SI/SO:
W.CLK:
ID:
The CIO port combinations for MIO checking
are fixed, so other combinations can not be
selected.
TO CONSOLE 1 ENGINE A1
TO CONSOLE 1 ENGINE A2
TO CONSOLE 2 ENGINE B1
TO CONSOLE 2 ENGINE B2
Please select 68pin ports to check.
[TO CONSOLE Port]
[ENGINE Port] A1 B2
OK
When changing to the next port, a pop-up box like
that below is displayed, so change the connections in
order according to the instructions and check
Connect [ENGINE A1] to [TO CONSOLE 1].
OK CANCEL
NG example
11. CS1D-Communication
* ETHER (EIF [A])
CH1
OK
OK
CH2
OK
* ETHER (EIF [B])
OK
CH1
OK
CH2
* ETHER (CCAS)
CH1
CH2
* RS232C
* USB
12-1. CS1D-MIO
(ENGINE A1) Test
This test checks the MIO (Engine
A1 port).
Check item
SI/SO
W.CLK
ID
• In
• Out
MSB/LSB
2CH/4CH
12-3. CS1D-MIO
(ENGINE B1) Test
This test checks the MIO (Engine
B1 port).
Check item
SI/SO
W.CLK
ID
• In
• Out
MSB/LSB
2CH/4CH
NG sample
Please refer to page 111 for NG chart.
OK
OK
OK
Other combinations
can not be selected.
ID change jig DIP switch
setting display
11. CS1D-Communication
NG
ETHER (EIF [A]):
CH1 NG
CH2 NG
NG
ETHER (EIF [B]):
CH1 NG
CH2 NG
ETHER (CCAS):
NG
CH1 NG
CH2 NG
RS232C:
USB:
NG
USB open error. Please check
NG
USB-Device-Driver on HostPC.
12-2. CS1D-MIO
(ENGINE A2) Test
This test checks the MIO (Engine
A2 port).
Check item
SI/SO
W.CLK
ID
• In
• Out
MSB/LSB
2CH/4CH
12-4. CS1D-MIO
(ENGINE B2) Test
This test checks the MIO (Engine
B2 port).
Check item
SI/SO
W.CLK
ID
• In
• Out
MSB/LSB
2CH/4CH
NG
NG
NG
NG
NG