Yamaha CS1D Service Manual page 133

14-3.CS1D-DIG I/O(AES/EBU) OK
* AES/EBU 3 (St.OUT A ->2Tr.IN 3)
OK
* AES/EBU 4 (St.OUT A ->2Tr.IN 4)
OK
* AES/EBU 5 (St.OUT B ->2Tr.IN 5)
OK
* AES/EBU 6 (St.OUT B ->2Tr.IN 6)
OK
15. CS1D- ANALOG INPUT (2Tr.IN, TalkBack) Test
This test inspects the 2Tr.IN analog 1L/1R/2L/2R and TalkBack (LMY4-AD board and ADCOM board) analog characteristics. At
this time, MONITOR OUT has already been inspected in 15. (If 2Tr.IN (LMY4-AD)) has already been inspected, it is ignored.
After the output destination has been specified with the pop-up box, the measurements are carried out manually according to the
Overall Inspection Specifications.
15.CS1D-ANALOG INPUT OK
* ANALOG INPUT(2Tr.IN,TalkBack)
OK
Choose INPUT PORT and check input characteristics.
2Tr.IN ANALOG
(1L/1R/2L/2R)
Talk Back
(1/2/---/---)
+10dB
+48V
-44dB
OK
Phantom power supply
On/Off control button
16. CS1D-ANALOG OUTPUT (MONI, CUE) Test
This test inspects the monitor, cue, TRS, and phone (ADCOM port and HPCOM port) analog characteristics. At this time, in order
to correctly inspect the output characteristics, use an LMY-4AD card that has already been inspected. (Refer to the LMY4-AD
Overall Inspection Specifications.)
After the output destination has been specified with the pop-up box, the measurements are carried out manually.
16.CS1D-ANALOG OUTPUT OK
* ANALOG OUTPUT (MONI,CUE)
OK
Choose OUTPUT PORT and check output characteristics.
2Tr.IN ANALOG
TO
(1L/1R/2L/2R)
OK
14-2.CS1D-DIG I/O (AES/EBU 3-6)
AES/EBU 3 (St.OUT A ->2Tr.IN 3):
AES/EBU 4 (St.OUT A ->2Tr.IN 4):
AES/EBU 5 (St.OUT B ->2Tr.IN 5):
AES/EBU 6 (St.OUT B ->2Tr.IN 6):
15.CS1D-ANALOG INPUT
Specifies the MONITOR OUT audio input
source. The input sources and monitors
correspond 1-to-1 in the order of in which
they are displayed.
(Example: 2Tr.IN 2L
TO MONITOR OUT
(AL/AR/BL/BR)
NG
Input level (GAIN) The inspector
switch button judges OK/NG.
16.CS1D-ANALOG OUTPUT
Specifies the 2Tr.IN audio output destination.
The output destinations and input sources
MONITOR OUT
correspond 1-to-1 in the order of in which
(AL/AR/BL/BR)
they are displayed.
(Example: 2Tr.IN 2L
CUE OUT
(L/R/---/---)
PHONE OUT
(AL/AR/BL/BR)
NG
The inspector
judges OK/NG.
NG example
14-3.CS1D-DIG I/O(AES/EBU)
* AES/EBU 3 (St.OUT A ->2Tr.IN 3)
* AES/EBU 4 (St.OUT A ->2Tr.IN 4)
OK
OK
* AES/EBU 5 (St.OUT B ->2Tr.IN 5)
OK
* AES/EBU 6 (St.OUT B ->2Tr.IN 6)
OK
Now Checking ...
AES/EBU 6
NG example
15.CS1D-ANALOG INPUT
* ANALOG INPUT(2Tr.IN,TalkBack)
MONITOR BL)
NG example
16.CS1D-ANALOG OUTPUT
* ANALOG OUTPUT (MONI,CUE)
MONITOR BL)
14-2.CS1D-DIG I/O (AES/EBU 3-6)
NG
NG
AES/EBU 3 (St.OUT A ->2Tr.IN 3):
AES/EBU 4 (St.OUT A ->2Tr.IN 4):
NG
AES/EBU 5 (St.OUT B ->2Tr.IN 5):
NG
AES/EBU 6 (St.OUT B ->2Tr.IN 6):
15.CS1D-ANALOG INPUT
NG
ANALOG INPUT(2Tr.IN,TalkBack):
16.CS1D-ANALOG OUTPUT
NG
ANALOG OUTPUT (MONI,CUE):
CS1D
NG
NG
NG
NG
NG
NG
124