Related Manuals for Linkcom link smile
Summary of Contents for Linkcom link smile
- Page 1 Link Smile DoorPhone Manual v1.0 Please find the latest version of the manual and firmware at www.linkcom.fr Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2009 – Linkcom – All rights reserved...
-
Page 2: Table Of Contents
6.1. E lectrical p arameters .............................. 2 1 6.2. M echanical d imensions .............................. 2 1 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2009 – Linkcom – All rights reserved... -
Page 3: Basic Description
7. Relays connector (max. 48V / 1,5A) 8. 12V power supply connector. The power supply is necessary for the relay, the motherboard heating and cards backlighting. Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 4: Installation
2. Installation 2.1 Assembly Open and close the cover: Dismounting lighting of nameplate: Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 5: Wall Mounting
Return lighting nameplate after mounting on the wall. Each button has its separate nameplate hold by means of plastic flag (see figure). Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 6: Connection
Link Smile DoorPhone announces by sound signal. We not recommend connecting the Link Smile DoorPhone in parallel with other analog phone. Attention: The line is necessary to program the Link Smile DoorPhone by the software. -
Page 7: Smile Doorphone Service
2 groups numbers mode: On the first press the number set in parameter 1 will be dialed. When • the same button is pushed or 10 seconds after dial busy tone is detected, or setup number of Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 8: Telephone Caller
You will hear the call connection confirmation tone; the confirmation tone for programming mode and afterwards the Programming tone is heard. (see Chapter 3.1). Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 9: Parameter Programming
The unit will answer and, providing the program is running, it will confirm its entry into programming mode again. When the connection is correct, you can the firmware version of Smile DoorPhone (visible in bar). Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 10: Parameter Description
First code aa from phone for relay r aa 1 55 activating r (00-99,*0-*9) Second code aa from phone for relay r cc 1 50 activation r (00-99,*0-*9) Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 11: Basic Parameters
Description Default xxxx Service password (0000-9999) 0000 xxxx – service password for entry to programming by phone (DTMF) Parameter Value Description Default Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 12: Time Parameters
D – Maximum time in minutes for which a call may last. This time can be extended during a call by dialing Prolong Call digit from telephone (∗ or #). Time setting is per table. 1 - 9 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... - Page 13 10 (100ms) tone (04-16) Time of Flash duration (1-6) 1 (100ms) Time of pause duration / pause between 4 (800ms) numbers (1-0) Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved...
-
Page 14: System Parameters
- dial [dB] 5.5. System parameters frequency x - dial [Hz] 275-375 325-425 375-475 425-525 475-575 525-625 575-675 625-725 675-775 725-825 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... - Page 15 To increase security you can activate suppression of DTMF reception from microphone i=1. Parameter Value Description Default BabyCall – call without necessity program phone number (0/1) Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved...
-
Page 16: Handsfree Parameteres Setting
It is going about character of on line operation semiduplex switching. In case where character of depressed is too steep you can make it softer by c=1. Parameter Value Description Default Depression of background sound (0/1) Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... - Page 17 You can setup in two levels depending on line current of PBX (short circuit current I PBX current I k - dial Feature is off 20mA-50mA 45mA-75mA Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved...
-
Page 18: Default Setting And Erasing
The parameters 81 and 82 will delete all numbers stored in memories for buttons. Attention: the deletion is non-reversible!!! Numbers must be programmed again. 5.8. Exit programming Parameter Value Description Default Enf of programming Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... -
Page 19: Parameters Overview
(1-5) Duration time of tone DTMF of tone dial 10 (100ms) (04-16) Time of space between each DTMF tones 10 (100ms) (04-16) Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved... - Page 20 Default setting for Parameters 3x only Default setting for Parameters 4x only Default setting for Parameters 5x only Default setting for Parameters 6x only Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved...
-
Page 21: Technical Parameters
Brave Slim 185 x 99 x 40 Screw 2x Screw 3.5x30 half round head Wall plug 2x UPA,UPP pr. 5 x 25 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2011 – Linkcom – All rights reserved...