Related Manuals for Linkcom SlimDoorPhone 1 button
Summary of Contents for Linkcom SlimDoorPhone 1 button
- Page 1 Manuel V2.2 find the latest version of the manual and firmware at www.linkcom.fr Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés...
-
Page 2: Table Of Contents
7 Table f or e asy p rogramming .................... 19 8 Drilling m aster b oard ...................... 21 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 3: Basic Description
2. Push the name card panel down and then push it towards to grille (see figure-2). 3. The panel will be released. Pull it towards you to remove (see figure – 3). Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 4: Uncover Control Elements
(central) and "NC" means contact normally closed. The relay contact is isolated from the other circuits on the board. For the variants of lock connection see the picture below. Telephon e line Power supply lock Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 5: Switches
Voice interruption might occur if you set the amplification too high. In this case you can use the trimmer TRH to correct the balance between the speaker and the microphone. Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 6: Location Of Id Doorphone Components
12V =/~ for Telephone relay, light line connection and heating Hole for lead in cable Relay Buttons Microphon Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 7: Changing Name Cards
(see figure - 3). 4. Push the name card panel back down behind the lip of the casing (see figure - 4). Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 8: Slimdoorphone Services
36 . Then it will hang up. 3.3 Telephone Caller A Telephone Caller is a person that is in phone connection with SlimDoorPhone. Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 9: Outgoing Call
Every time a DTMF tone is dialled, this period is reset. Alternatively, parameter 9 may also be selected to end programming mode. Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 10: Programming From A Pc - Id Manager Program
USB – tool 5 Parameter description 5.1 Direct Dialling – Memories Parameter Value Description Default Exam.1 Exam.2 No. nn under t nn… button t Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 11: Relay
§ frequent use. Select the first password button from infrequently-used buttons for direct dialling (- § extends choice time)(-not valid for keyboard). Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 12: Basic Parameters
0000 Password xxxx – service password for entry to programming Paramet Valu Exam. Exam. Description Default DAY MODE switching NIGHT MODE switching Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 13: Time Parameters
– time [sec] for which the unit will hang up, before repeat dialling (button pressing during call or dialling, busy tone detection) [range 1-5] Paramet Exam. Exam. Value Description Default Call start time Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... - Page 14 Number of busy tones before hahg x – is number of busy tones before hahg up by next table: number of busy tones number of busy tones Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés...
-
Page 15: Presetting And Deleting
The parameters 81 and 82 will delete all numbers stored in memories for buttons. The parameters 83 – 85 will execute a selective basic setting only for parameters starting with 3.. – 5.. Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 16: Exit Programming
– standard operation t=0 – delayed start 5.8 Overview of Parameters Parameter Value Description Default Exam.1 Exam.2 No. nn under t nn… button t Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... - Page 17 Delay of line connection (Siemens PBX) Acoustic signalling 3 and 9 3 and 9 3 and 9 executes Default setting Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés...
-
Page 18: Technical Parameters
I < 1A contact Max. current of switch at U < 30 V contact Operational temperature - 20 to + 50°C Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... -
Page 19: Mechanical Dimensions
On hook time before new [sec] call Call start time [sec] Number of rings before hang up or group mode switching DTMF tone duration (n+5)x10 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés... - Page 20 Gap between DTMF (n+5)x10 tones Recall duration nx100 Pause duration nx100 Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés...
-
Page 21: Drilling Master Board
8 Drilling master board Linkcom France 11 rue du Soleil Levant 92140 CLAMART Copyright © 2012 – Linkcom – Tous droits réservés...
Need help?
Do you have a question about the SlimDoorPhone 1 button and is the answer not in the manual?
Questions and answers