Page 1

User's Guide...
Page 2: Organization Of The Guide And Notations In The Guide

Organization of the Guide and Notations in the Guide Using Each Guide The guides for this projector are organized as shown below. Safety Instructions/Support and Service Guide Contains information on using the projector safely, as well as a support and service guide, troubleshooting check lists, and so on.
Page 3: Notations Used In This Guide

Organization of the Guide and Notations in the Guide Notations Used in This Guide Safety Indications The User's Guide and the projector use graphical symbols to show how to use the projector safely. The following shows the symbols and their meanings. Please understand and respect these caution symbols in order to avoid injury to persons or property.
Page 4: Table Of Contents

Contents Connecting MHL devices (EH-LS9600W only) Organization of the Guide and ........23 Notations in the Guide Connecting to the LAN port .
Page 5

Contents Range for Viewing 3D Images ....42 Saving the Memory ..... 64 Converting 2D Images to 3D Images and Loading the Memory .
Page 6

Contents Network menu ..... . . 96 MHL Input Signals (via a WirelessHD Transmitter*) ......119 Info menu .
Page 7: Preparing

Preparing Part Names and Functions Front/Top Name Function a Indicators The color of the indicators and whether they are flashing or lit indicate the status of the projector. p.10 b Control panel Retractable control panel on the side of the projector. p.10 c Front adjustable foot Adjust the projector's horizontal tilt when placing and projecting.
Page 8: Rear

Preparing Name Function g Air exhaust vent Exhaust vent for air used to cool the projector internally. Caution While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent.
Page 9: Interface

Preparing Interface Name Function a HDMI1/HDMI2 ports Connects HDMI compatible video devices and computers. p.21 b Cable holders Insert the supplied HDMI cable clamp. Because thick HDMI cables with a large outer diameter, may disconnect easily due to the weight of the cable, secure the cables with the HDMI cable clamp.
Page 10: Base

Preparing Base Name Function a Air intake vent When suspending from a ceiling, install the projector so that dust does not collect in the vent. b Screw holes for ana- Screw holes for attaching the anamorphic lens. morphic lens Front adjustable foot Adjust the projector's horizontal tilt when placing and projecting.
Page 11: Control Panel

Preparing Control Panel Buttons/Indicators Function Flashes orange if the internal temperature is too high. Shows the projector's errors through a combination of other indicators lit and flashing. p.101 Lit orange when an error occurs in the laser section. Shows the projector's errors through a combination of other indicators lit and flashing.
Page 12

Preparing Buttons/Indicators Function Move vertically and horizontally to select the adjustment value for the Config- uration menu item. p.29 Move vertically while projecting an image to correct keystone distortion. p.34 When the Configuration menu is displayed, it accepts and enters the current selection and moves to the next level.
Page 13: Remote Control

Preparing Remote Control Top section buttons EH-LS10000 EH-LS9600W Button Function Turns the projector on. p.27 Turns the projector off. p.28 The remote control buttons light up for approximately 10 seconds. This is useful when operating the remote control in the dark.
Page 14

Preparing Button Function Performs operations such as play and stop for connected devices that meet the HDMI CEC standards. p.60 Displays the HDMI link settings menu. p.60 Adjusts the volume for connected devices that meet the HDMI CEC standards.
Page 15

Preparing Middle section buttons Button Function Changes the adjustment item for the motorized lens function. The following adjustment items are available. • Focus s p.32 • Zoom s p.33 • Lens shift s p.33 Changes the Color Mode. p.44 Changes between 2D and 3D images. p.39 Selects the Configuration menu items and adjustment values.
Page 16

Reduces the jarring effect caused by quick movements by interpolating frames, and adjusts to render a smoother, clearer image. p.49 (EH-LS10000 only) Sets Super-resolution to reduce blurring in areas such as the edges of the image, or 4K Enhancement for ultra high definition images.
Page 17: Installing

Preparing Installing Notes on Installing Warning Ceiling mount installations • A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury. •...
Page 18: How To Install

Preparing How to Install The projector can be installed using a variety of methods, such as placing on a shelf or suspending from a ceiling. Using the lens shift function gives you more flexibility to place the projector where you want. p.33 Placing on a shelf and projecting You can install the projector in an AV rack or on a shelf in your living room to project images.
Page 19: Projection Distance And Lens Shift Maximum Values

Preparing Projection Distance and Lens Shift Maximum Values The size of the projection increases as the projector is moved away from the screen. Use the following table to setup the projector so that it projects at the optimum size. The values given here are for your reference only. You can also adjust the position by projecting using lens shift.
Page 20

Preparing Unit: cm 16:9 Projected Image Size Projection Distance (E) Lens Shift Maximum Values W x H Minimum Maximum Distance Distance Distance (Wide) (Tele) (C, D) 40" 89 x 50 60" 130 x 75 80" 180 x 100 100" 220 x 120 120"...
Page 21: Connecting A Device

Preparing Connecting a Device Attention • Make cable connections before connecting to a power outlet. • Check the shape of the cable's connector and the shape of the port, and then connect. If you force a connector of a different shape into the port, it could cause damage and a malfunction to occur. Removing the Cable Cover You can attach the cable cover to the rear of this projector to give it a clean and smooth look.
Page 22: Connecting Video Devices

Preparing Connecting Video Devices To project images from Blu-ray disc players or video recorders and so on, connect to the projector using one of the following methods. • Depending on the video device, there may be multiple types of output available. Check the documentation supplied with the video device to confirm the output types.
Page 23: Connecting A Computer

Preparing Connecting a Computer To project images from a computer, connect the computer using one of the following methods. Computers with an RGB output port Computers with an HDMI output port To prevent the weight of the HDMI cable disconnecting it from the port, make sure you secure it to the cable holder with the HDMI cable clamp.
Page 24: Connecting Wirelesshd Devices (eh-ls9600w Only)

Preparing Connecting WirelessHD devices (EH-LS9600W only) The projector receives transmissions from the WirelessHD Transmitter, and projects the images. p.67 Change the projected image by pressing the button on the remote control or the button on the control panel. • When receiving WirelessHD images, make sure WirelessHD is set to On. Settings - WirelessHD - WirelessHD p.91...
Page 25: Connecting To The Lan Port

Preparing Connecting to the LAN port Connect to a network router, a hub, and so on, with a 100BASE-TX or 10BASE-T LAN cable. You can operate the projector or check its status over a network from a computer or a smart device. •...
Page 26: Preparing The Remote Control

Preparing Preparing the Remote Control Installing Batteries Attention • Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way. • You cannot use other batteries except for the AA size manganese or alkaline. Remove the battery cover.
Page 27

Preparing The operation range for the WirelessHD Transmitter differs. p.75...
Page 28: Basic Operations

Basic Operations Turning the Projector On and Off Turning On Warning • Do not allow small children to make operations. If children do make operations, they must be accompanied by an adult. • Do not look into the lens during projection. Also, do not look into the lens using optical devices (such as a magnifying glass or telescope).
Page 29: Turning Off

Basic Operations • To obtain stable image quality, it is recommended that you leave the projector on for a while before starting operations. • This projector provides a Child Lock function to prevent children from accidentally turning the power on and a Control Panel Lock function to prevent accidental operations. Settings - Lock Setting - Child Lock/Control Panel Lock p.91...
Page 30: Configuration Menu Operations

Basic Operations Configuration Menu Operations Using the Configuration menu, you can make adjustments and settings for images or image quality. • For items adjusted using an adjustment bar, such as the brightness level, you can press the button while the adjustment screen is displayed to return the adjustment value to its default value. •...
Page 31

Basic Operations Press the button to exit the menu.
Page 32: Adjusting The Projected Screen

Immediately after installation, a test pattern is used to adjust the zoom, focus, and the projection position. Press the button on the remote control to display the test pattern. EH-LS10000 EH-LS9600W You can also select patterns that display R (red), G (green), and B (blue) individually, as well as the pattern for adjusting the display position.
Page 33: Adjusting The Focus

Basic Operations The adjustment items switch as shown in the following table. Focus adjustment Adjust Focus is displayed on the screen. Adjusts the focus of the projected image. p.32 Zoom adjustment Adjust Zoom is displayed on the screen. Adjusts the size of the projected image. p.33 Lens shift adjustment Adjust Lens Shift is displayed on the screen.
Page 34: Adjusting The Projection Size (zoom Adjustment)

Basic Operations Adjusting the projection size (zoom adjustment) Press the buttons to adjust the size of the projected screen. Adjusting the position of the projected image (lens shift) If the projector cannot be setup in front of the screen, you can adjust the position of the image by using lens shift.
Page 35: Keystone

Use keystone when you cannot make adjustments using lens shift. Switching the Source You can change the source using the following method. Press the button for the target port. EH-LS10000 EH-LS9600W • You can also change the source by pressing the button on the control panel.
Page 36: Aspect

Press the button. Use the buttons to select the setting name, and then EH-LS10000 EH-LS9600W press the button to confirm the selection. You can make settings from the Configuration menu.
Page 37: Hiding The Image Temporarily

You can use this to temporarily hide the image on the screen. Press the button to show or hide the image. EH-LS10000 EH-LS9600W • Because moving images continue to play even when they are hidden, you cannot return to the point at which you hid the images using the button.
Page 38: Viewing 3d Images

Charging • When charging, connect the supplied cable to the USB port designated by Epson. Do not charge using other devices as it may cause the battery to leak, overheat, or explode. • Only use the supplied charging cable to charge the 3D Glasses. Otherwise, it could overheat, ignite, or explode.
Page 39

Basic Operations Caution Wearing 3D Glasses • Make sure you wear the 3D Glasses correctly. Do not wear the 3D Glasses upside down. If the image is not displayed correctly into the right and left eyes, it could cause you to feel unwell. •...
Page 40: Projecting 3d Images

The projector automatically projects a 3D image when detecting a 3D format. When the projector cannot detect a 3D format Some 3D TV broadcasts may not contain 3D format signals. If EH-LS10000 EH-LS9600W this happens, set the 3D format manually. Press the...
Page 41: If The 3d Image Cannot Be Viewed

Basic Operations • For details on 3D format settings on the AV device, see the documentation supplied with the AV device. • When the 3D format has not been set up correctly, the same image is split horizontally or vertically and is not projected correctly as shown below.
Page 42: Charging The 3d Glasses

Basic Operations Charging the 3D Glasses The following charging methods are available, depending on the model of 3D Glasses being used. If you have a WirelessHD Transmitter, you can use it to charge the glasses. If you do not have a WirelessHD Transmitter, you can charge by using an optional USB Charging Adapter. Charging using the WirelessHD Transmitter Charging using the USB Charging Adapter Use the USB cable to connect the 3D Glasses to...
Page 43: Wearing And Viewing With The 3d Glasses

Basic Operations Wearing and viewing with the 3D Glasses Turn on the 3D Glasses by sliding the Put on the 3D Glasses and enjoy the [Power] switch to On. show. The indicator turns on for several seconds, • When you have finished using the and then turns off.
Page 44: Converting 2d Images To 3d Images And Viewing

Basic Operations Converting 2D Images to 3D Images and Viewing You can convert 2D images to 3D images from HDMI1, HDMI2, or WirelessHD (EH-LS9600W only). Press the button, select Signal - Select the strength of the 3D effect, and then press the button to 3D Setup from the Configuration menu, and then press the...
Page 45: Setting Image Quality

Setting Image Quality Basic Color Mode You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the image varies depending on the mode selected. Press the button. You can make settings from the Configuration menu. Image - Color Mode p.86 Select Color Mode.
Page 46

Projects a brighter, more vivid image than 3D Cinema. 3D Dynamic 3D Cinema Produces crisper colors than 3D Dynamic. A color mode authorized by THX Ltd. 3D THX May not be displayed depending on the model you are using. EH-LS10000 only...
Page 47: Super-resolution

24 Hz/frame packing signals. Super-resolution/4K Enhancement This function is only available for EH-LS10000. There are two types of setting available, Super-resolution and 4K Enhancement. When a low resolution image is input to the projector, it is increased to 1920 x 1080 pixels. Super- resolution sharpens blurred images, enhancing the apparent detail of the image by increasing the resolution of the image signal.
Page 48

Setting Image Quality Press the button. • You can make settings from the Configuration menu. Signal - Super-resolution/4K p.88 • This cannot be set when a computer image signal is being input. • This cannot be set when converting 2D images to 3D images. Signal - 3D Setup - 2D-to-3D Conversion p.88...
Page 49: Detail Enhancement

Setting Image Quality Detail Enhancement This function enhances details in an image to create clear outlines. Press the button, select Signal - Use the buttons to Detail Enhancement from the select Strength, and then use the Configuration menu, and then press buttons to make the adjustments.
Page 50: Frame Interpolation

Configuration menu, and then press button to confirm the selection. The Dynamic Contrast adjustment screen is displayed. For EH-LS10000, you can also Press the button to exit the make settings by pressing the menu. button on the remote control.
Page 51: Precise Image Adjustment

Use the buttons to make adjustments. The RGBCMY adjustment screen is displayed. For EH-LS10000, you can also make settings by pressing the button on the remote control. Press the button to adjust another color. Press the...
Page 52: Gamma

Setting Image Quality Gamma You can adjust slight coloration differences that may occur due to the device being used when the image is displayed. You can use one of the following three methods selected from the Configuration menu. Setting Method Menu Settings Select and adjust the correction val- Image - Advanced - Gamma...
Page 53: Adjust Using The Gamma Adjustment Graph

Setting Image Quality Adjust using the gamma adjustment graph Make adjustments while viewing the gamma adjustment graph for the image being projected. Use the buttons to Use the buttons to select the adjust the brightness, and then press part you want to adjust from the button to confirm the graph.
Page 54: Color Temp

Setting Image Quality Color Temp. You can adjust the color temperature. Make adjustments if the image is a little too blue or too red. The menu is displayed in the following order. Image - Color Temp. Use the buttons to make adjustments. Blue tints grow stronger as the value is increased, and red tints grow stronger as the value is reduced.
Page 55

Setting Image Quality Press the button, select Image - Press the button to exit the menu. Sharpness from the Configuration menu, and then press the button to confirm the selection. The Sharpness adjustment screen is displayed. Select Advanced at the top right of the screen, and then press the button to confirm the selection.
Page 56: Lens Iris

Lens Iris from the Configuration menu, and then press the button to confirm the selection. The Lens Iris adjustment screen is displayed. For EH-LS10000, you can also make settings by pressing the button on the remote control. Use the buttons to make adjustments.
Page 57: Panel Alignment

Setting Image Quality Panel Alignment Adjusts the pixel color shift of the LCD display. • When projecting using lens shift to adjust the position of the image, once you have adjusted to a suitable position, perform panel alignment. p.33 • Panel alignment cannot be performed correctly when projecting using extreme keystone correction.
Page 58

Setting Image Quality After adjusting four corners, select Press the button to exit the menu. Exit, and then press the button to confirm. If the four corners still need adjustments, select Select intersection and adjust, and then continue adjustments.
Page 59: Image Processing

Setting Image Quality Image Processing Improves the image quality or response speed for projected images. This is only available when receiving a progressive signal input from the Component, Video, HDMI1, or HDMI2 ports, or from WirelessHD. Press the button to exit the Press the button, select Signal - menu.
Page 60: Color Gamut

Setting Image Quality Color Gamut Allows you to easily set the color gamut to match the standard for the video devices being used. This can be set when Color Mode is set to Natural. Select the item according to the Press the button, select Image - device being used.
Page 61: Useful Functions

Useful Functions HDMI Link HDMI Link Function When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI1/HDMI2 ports, you can perform linked operations such as linked power on and volume adjustment for the AV system from one remote control.
Page 62: Selecting The Connected Device

Useful Functions • To use the HDMI Link function, you must configure the connected device. See the documentation supplied with the connected device for more information. • When using the WirelessHD Transmitter, make the following settings when you want to use the power on/off link function (EH-LS9600W only).
Page 63: Lens Position Function

Press the button. The adjustment values are saved. EH-LS10000 EH-LS9600W If the mark on the left of the lens position name is turned green, it means the lens position has already been registered. When you select a registered lens position, a...
Page 64: Loading The Lens Position

Useful Functions Loading the Lens Position Press the button, and then select Load Lens Position. The Load Lens Position screen is displayed. Select the lens position name you want to load. The zoom, focus, and lens shift are adjusted to the status you saved. While adjustments are being performed, a message is displayed and the projector cannot be operated.
Page 65: Memory Function

You can save the following Configuration menu settings. Color Mode, Power Consumption, Brightness, Contrast, Color Saturation, Tint, Sharpness, Image Color Temp., Skin Tone, Dynamic Contrast p.86 Advanced Sharpness, Offset, Gain, Gamma, Hue, Saturation, Brightness, EPSON Super White Deinterlacing, Motion Detection, Super-resolution , Super-resolution/4K , Detail Enhance- Signal ment p.88...
Page 66: Loading The Memory

Useful Functions Use the buttons to select the memory name to be saved, and then press the button to confirm the selection. The current projector settings are saved as a memory. If the mark on the left of the memory name is turned green, it means the memory has already been registered.
Page 67: Erasing The Saved Memory

Useful Functions Erasing the Saved Memory Press the button, and then select Erase Memory. The Erase Memory screen is displayed. Select the memory name you want to erase. A confirmation message is displayed. Select Yes to erase the content of the saved memory. You can erase all of saved memories from Reset - Reset Memory on the Configuration menu.
Page 68: Connecting With Wirelesshd

Useful Functions Connecting with WirelessHD (EH-LS9600W Only) Installing the WirelessHD Transmitter You can use the supplied WirelessHD Transmitter to wirelessly receive image data. This is useful when the projector cannot be setup near your AV devices as you can connect the devices to the projector without using cables.
Page 69: Wirelesshd Transmitter Part Names

Useful Functions WirelessHD Transmitter part names Front Rear Name Function button Turns the WirelessHD Transmitter on or off. This performs the same function as the button for WiHD Transmit- ter on the lower section of the remote control. b Input button Changes to the image from each input port.
Page 70: Wirelesshd Transmitter Connection Example And Signal Flow

Useful Functions WirelessHD Transmitter connection example and signal flow Connection example 1: Viewing without an AV amplifier Connect a device to WirelessHD Transmitter without using an AV amplifier, and connect the sound bars and so on to the Optical Audio-Out port to output audio. When outputting audio from a connected device, you need an optical digital audio cable.
Page 71

Useful Functions Connection example 2: Viewing with a connected AV amplifier The audio from the device connected to the AV amplifier is output from the amplifier's audio-out port without passing through the WirelessHD Transmitter. When outputting audio from a device connected with an MHL cable, you need an optical digital audio cable. The audio output method to an AV amplifier may be restricted by the specifications of the monitor device, such as a television, connected to the Output port.
Page 72: Setting The Wirelesshd Transmitter

Useful Functions Setting the WirelessHD Transmitter Set up the WirelessHD Transmitter Using an HDMI cable, connect the AV connected to the projector so that device you want to use to the Input they are facing each other. p.74 port on the WirelessHD Transmitter. You can connect up to five AV devices.
Page 73: Projecting Images

Useful Functions Projecting Images Start playback on the AV device, and then turn on the projector and the WirelessHD Transmitter. indicator on the WirelessHD Transmitter turns on. Check the status of the WiHD indicator on the WirelessHD Transmitter. If the WiHD indicator is on, go to the next step. If the indicator is off, press the button on the remote control or the WirelessHD Transmitter.
Page 74: Wirelesshd Settings Menu

Useful Functions If projection does not start, press the button on the remote control to change the source. Make sure you point the remote control at the projector when using the button on the remote control. Projection starts. When connecting two or more AV devices to the WirelessHD Transmitter, press the button to switch images.
Page 75: Wirelesshd Transmission Range

Useful Functions Function Explanation Reset Resets WirelessHD settings to their default settings. Even when the WirelessHD Transmitter and the projector are connected, 0% is displayed as the Reception when no image signal is being input. Check the communication status using the Link indicator.
Page 76: Remote Control Operating Range

Useful Functions • The wireless transmission range varies depending on the placement and material of the surrounding furniture and walls. The values given here are for your reference only. • The projector cannot communicate through walls. • Place the WirelessHD Transmitter on a wooden shelf or other location that does not block the signal from being transmitted from the front of the device.
Page 77: Switching The Image Source

Useful Functions Point the remote control at the WirelessHD Transmitter, and then press the button. Remote control WirelessHD Transmit- Depending on the output target, the WiHD indicator on the WirelessHD Transmitter indicates the following status. On: The image is being output to the projector. Off: The image is being output to the monitor device.
Page 78

Useful Functions Point the remote control at the The target screen changes each time WirelessHD Transmitter, and then you press the button. press the button. Remote control WirelessHD Trans- mitter Displays the sub-screen (small screen) for the connected device. The screen that is not receiving an image signal is displayed in blue or black.
Page 79: Displaying As A Sub-screen

Useful Functions Displaying as a Sub-Screen Point the remote control at the To close the sub-screen, press the WirelessHD Transmitter, and then button again. press the button. The projected image is switched. • When the sub-screen is displayed, press the button to switch the image for the sub- screen.
Page 80: Picture In Picture

Starting and Exiting Picture in Picture Starting Press the button on the remote control while the projector is projecting. EH-LS10000 EH-LS9600W The currently input image is displayed on a Picture in Picture. Main screen: The current image Sub screen: The source different from the main screen...
Page 81: Picture In Picture Settings

Useful Functions Picture in Picture Settings Use the Picture in Picture menu to change the size or position of the sub screen. Press the button, select Make settings for each of the displayed functions. Settings - Picture in Picture from the Configuration menu, and then press button to confirm the selection.
Page 82: Operations And Settings Using The Network

Useful Functions Operations and Settings Using the Network When the projector is connected to a network, you can make settings and control the projector from a computer or smart device over the network. Making Settings and Performing Operations from a Web Browser When a computer or smart device with a Web browser is connected to the same network as the projector, you can change the projector's settings in the same way as operating a remote control.
Page 83: Operating The Projector (web Remote)

Useful Functions Displaying the Web Control screen on your smart device Start the Web browser, and then enter the IP address of the projector in the address input box of the Web browser. The remote and config icons are displayed in your Web browser. Tap the config icon.
Page 84

Useful Functions Displaying the Web Remote screen on your smart device Start the Web browser, and then enter the IP address of the projector in the address input box of the Web browser. The remote and config icons are displayed in your Web browser. Tap the remote icon.
Page 85: Using The Mail Notification Function To Report Problems

When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent. Subject: EPSON Projector Line 1: The projector name where the problem has occurred Line 2: The IP address set for the projector where the problem has occurred Line 3 and on: Details of the problem The details of the problem are listed line by line.
Page 86

Useful Functions Message Contents Remedy Internal error Internal error Handling errors or warnings is the same as checking the status of the indicators. Laser driver error p.101 Fatal error Lens cover error Fan related error Fan error Sensor error Sensor error Light sensor error Cinema Filter Error Cinema filter error...
Page 87: Configuration Menu

Configuration Menu Configuration Menu Functions Configuration Menu Table If there is no image signal being input, you cannot adjust items related to the image or signal in the Configuration menu. Note that the items displayed for the image, the signal, and other information vary depending on the image signal being projected.
Page 88

Image to their default settings. This may not be displayed depending on the model you are using. Only EH-LS10000 is displayed. This is not displayed when a computer image signal is being input. When Color Mode is set to Natural, THX, Adobe RGB, or 3D THX the settings change to 5000K - 10000K.
Page 89: Signal Menu

Configuration Menu Signal menu Function Menu/Settings Explanation *1 *2 3D Setup 3D Display On, Off Enables or disables the 3D image display func- tion. p.39 2D-to-3D Conver- Off, Weak, Medium, Sets the strength of the 3D effect when convert- sion Strong ing 2D images to 3D images.
Page 90

Reduces blurring that occurs at the edge of im- ages when the resolution is increased. p.46 Super-resolu- Off, 1, 2, 3, 4, 5, 4K-1, 4K-2, 4K-3, 4K-4, 4K-5 (EH-LS10000 only) *2 *6 tion/4K Super-resolution (1 to 5) reduces blurring that occurs at the edge of images when the image is increased to 1920 x 1080 pixels.
Page 91

This cannot be set when an HDMI1, HDMI2, or WirelessHD image signal is being input. This is not displayed when a PC image signal is being input. Settings are saved for each setting in Source, Color Mode, Super-resolution/4K (EH-LS10000), or Super- resolution (EH-LS9600W).
Page 92: Settings Menu

Configuration Menu Settings menu Function Menu/Settings Explanation Keystone -60 - 60 Performs vertical keystone correction. p.34 HDMI Link Device Connections - Displays a list of devices connected from the HDMI1 or HDMI2 ports, or from WirelessHD HDMI Link On, Off Enables or disables the HDMI Link function.
Page 93

Configuration Menu Function Menu/Settings Explanation Lock Setting Lens Lock On, Off When set to On, the focus, zoom, and lens shift settings are locked at their current settings. If you press the button when Lens Lock is set to On, is displayed on the screen.
Page 94

Configuration Menu Function Menu/Settings Explanation Operation Direct Power On On, Off You can set up the projector so that projection starts as soon as the power cord is plugged in without any button operations. Note that when this is set to On, projection starts if power is restored after a blackout or other power outage and the power cord is still plugged into the projector.
Page 95

Configuration Menu Function Menu/Settings Explanation Display Menu Position Sets the position where the menu should be dis- played. Menu Color Color 1, Color 2 Selects the color for the Configuration menu. • Color 1 Main menu: Black Selected items: Gray •...
Page 96: Memory Menu

High Altitude Mode • Component • Language Only EH-LS9600W is displayed. Only EH-LS10000 is displayed. Cannot be set when a 4K image signal is being input. Memory menu Function Explanation Load Memory Loads settings saved using the Save Memory function.
Page 97: Network Menu

Configuration Menu Network menu When you have made network settings for the projector and you connect to a computer or smart device on the network, you can change settings from your Web browser without displaying the Configuration menu, or you can use the computer or smart device as a remote control. Also, when mail notification settings have been made and an error or warning occurs in the projector, a notification email is sent to the email addresses you have specified.
Page 98

Configuration Menu Function Explanation Web Control Password Set a password to use Web Control. You can enter up to 32 single-byte alpha- numeric characters. (* cannot be used.) Web Control is a function that allows you to change the projector's settings by using the Web browser on a computer or smart device connected to the network.
Page 99

Bonjour. See Apple's Web site for more in- formation on the Bonjour service. http://www.apple.com/ Only EH-LS10000 is displayed. Reset menu To reset all of the network settings, select Yes. After you reset all the settings, the Basic menu appears.
Page 100: Info Menu

Configuration Menu • Each time the CAPS key is selected and the button is pressed, it sets and changes between upper case and lower case letters. • Each time the SYM1/SYM2 key is selected and the button is pressed, it sets and changes the symbol keys for the section enclosed by the frame.
Page 101: Reset Menu

Configuration Menu Reset menu Function Explanation Reset All Resets all items in the Configuration menu to their default settings. The following items are not reset to their defaults: Input Signal - Component, Panel Alignment, Language, Save Memory, Save Lens Position, and Opera- tion Hours.
Page 102: Troubleshooting

• If turning the power back on does not clear the problem, stop using the projector and remove the power plug from the electrical outlet. Contact your local dealer or the Epson Projector Contact nearest Epson repair center. s List...
Page 103

If the problem does not improve even after trying the solutions mentioned above, stop using the projector and remove the power plug from the electrical outlet. Con- tact your local dealer or the nearest Epson repair center. Epson Projector Contact List...
Page 104: Indicator Status During Normal Operation

Troubleshooting Indicator status during normal operation : Lit : Flashing : Off Indicators Status Remedy Standby condition When you press the button on the remote control, or the button on the control panel, projection starts. Standby condition When you press the button on the remote control, or the (Standby Mode is set to button on the control panel, projection starts.
Page 105: When The Indicators Provide No Help

Troubleshooting When the Indicators Provide No Help Check the problem Check the following table to see if your problem is mentioned, and go to the appropriate page for information on handling the problem. Problem Page Problems relating to im- No images appear p.105 ages Projection does not start, the projection area is completely black, or the...
Page 106: Problems Relating To Images

Troubleshooting Problems relating to images No images appear Check Remedy Is the power turned on? Press the button on the remote control or the button on the control panel. Is the power cord connected? Connect the power cord. Are the indicators switched off? Disconnect and then reconnect the projector's power cord.
Page 107

Troubleshooting "Not supported" is displayed Check Remedy Is the image signal format setting correct? When Video is input If nothing is projected even when Video Signal is set to Auto from the Configuration menu, set the signal that matches the connected device.
Page 108

Troubleshooting Images are fuzzy or out of focus Check Remedy Has the focus been adjusted? Adjust the focus. p.32 Is the projector at the correct distance? Check the recommended projection range. p.18 Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy.
Page 109

Troubleshooting Image colors are not right Check Remedy Is the image signal format setting correct? When Video is input If nothing is projected even when Video Signal is set to Auto from the Configuration menu, set the signal that matches the connected device.
Page 110: Problems When Projection Starts

If the problem continues, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest projector information Epson Projector Contact List center. Problems with the remote control The remote control does not respond...
Page 111: Problems With The Control Panel

Troubleshooting Check Remedy Are the batteries dead or have the batteries Make sure the batteries are inserted correctly or replace the bat- been inserted correctly? teries with new ones if necessary. p.25 Is the remote control pointed at the Wire- Make sure you point the remote control at the WirelessHD Trans- lessHD Transmitter when operating the WiHD mitter when using the WiHD Transmitter buttons on the remote...
Page 112: Problems With Hdmi

Troubleshooting The 3D image is enlarged and truncated Check Remedy Is the correct 3D video format set? Video may be truncated if an incorrect 3D format is set. Set the correct 3D format. p.37 Problems with HDMI HDMI Link does not function Check Remedy Are you using a cable that meets the HDMI...
Page 113

Troubleshooting Check Remedy Are signals being received within the Wire- Check the Wireless HD transmission range, and view within that lessHD transmission range? range. p.74 Is the supplied WirelessHD Transmitter Check the indicator on the WirelessHD Transmitter. If there is turned on? no power being supplied, make sure the connector for the AC adapter is securely connected, and then turn on the power...
Page 114: Maintenance

Maintenance Maintenance Cleaning the Parts You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate. Warning Do not use sprays that contain flammable gas to remove dirt and dust from the projector's air filter, and so on.
Page 115

Maintenance Remove the air filter. Remove any dust remaining on the air filter by using a vacuum cleaner from Grip the knob in the center of the air filter the front side. and pull it out at an angle. Hold the air filter with the surface Replace the air filter if a message is facing down and tap it 4 or 5 times to displayed even after cleaning the...
Page 116: Cleaning The Main Unit

• Do not touch the projection lens. When cleaning the lens, contact your local dealer or the nearest projector Epson Projector Contact List information center. Cleaning the 3D Glasses Clean the lenses of the glasses by wiping them gently with a soft cloth.
Page 117: Appendix

Appendix Optional Accessories and Consumables The following optional accessories/consumables are available for purchase if required. This list of optional accessories/consumables is current as of: 2014.1. Details of accessories are subject to change without notice. Varies depending on country of purchase. Optional Items Name Model No.
Page 118: Supported Resolutions

1920 x 1080 4K x 2K 24/25/30/50/60 3840 x 2160 50/60 4096 x 2160 4K x 2K (SMPTE) 4096 x 2160 EH-LS10000 only Component Video Signal Refresh Rate (Hz) Resolution (dots) SDTV (480i) 720 x 480 SDTV (576i) 720 x 576...
Page 119: Computer Signals (analog Rgb)

Appendix Computer Signals (Analog RGB) Signal Refresh Rate (Hz) Resolution (dots) 60/72/75/85 640 x 480 SVGA 56/60/72/75/85 800 x 600 60/70/75/85 1024 x 768 SXGA 70/75/85 1152 x 864 60/75/85 1280 x 960 60/75/85 1280 x 1024 WXGA 1280 x 768 1366 x 768 60/75/85 1280 x 800...
Page 120: Mhl Input Signals (via A Wirelesshd Transmitter*)

Appendix MHL Input Signals (via a WirelessHD Transmitter Signal Refresh Rate (Hz) Resolution (dots) SDTV (480i) 720 x 480 SDTV (576i) 720 x 576 SDTV (480p) 720 x 480 SDTV (576p) 720 x 576 HDTV (720p) 50/60 1280 x 720 HDTV (1080i) 50/60 1920 x 1080...
Page 121: Notes On Transportation

Appendix Notes on Transportation There are many glass parts and precision components inside the projector. To prevent damage due to impacts when transporting, handle the projector as follows. Moving Nearby Before carefully moving the projector, make sure it has been turned off and all cables have been disconnected. Attention •...
Page 122: Specifications

Appendix Specifications Product name EH-LS10000 EH-LS9600W Appearance (not including adjustable 550 (W) x 225 (H) x 553 (D) mm foot) Panel size 0.74" wide Display method Polysilicon TFT active matrix Resolution 1920 (W) x 1080 (H) x 3 Focus adjustment...
Page 123

Appendix Settings - Standby Mode - Communication On p.91 For EH-LS10000, the HDMI1 port supports HDCP 2.2, and the HDMI2 port supports HDCP 1.4. For EH-LS9600W, both ports support HDCP 1.4. Angle of tilt If you use the projector tilted at an angle of more than 3°, it could be dam- aged or cause an accident.
Page 124

HDMI1 INPT 32 HDMI2 INPT 33 WirelessHD INPT 34 Component INPT 24 Video INPT 21 INPT 11 EH-LS9600W only Manufacturer name displayed for "Manufacture name information query" EPSON Model name displayed for "Product name information query" EPSON 10000 EPSON 9600...
Page 125

DECLARATION of CONFORMITY According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers Epson America, Inc. Located at: 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806...
Page 126

Appendix Indication of the manufacturer and the importer in accordance with requirements of directive 2011/65/ EU (RoHS) Manufacturer: SEIKO EPSON CORPORATION Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan Telephone: 81-266-52-3131 Importer: SEIKO EUROPE B.V. Address: Azië building, Atlas ArenA, Hoogoorddreef 5, 1101 BA Amsterdam Zuidoost The Netherlands...
Page 127: Appearance

Appendix Appearance Units: mm Center of lens Distance from center of lens to suspension bracket fixing point Lens direction M4×9 M4×9...
Page 128: Glossary

Appendix Glossary This section briefly explains the difficult terms that are not explained in context in the text of this guide. For details, refer to other commercially available publications. The ratio between an image's length and its height. Screens with a horizontal:vertical ratio Aspect Ratio of 16:9, such as HDTV screens, are known as wide screens.
Page 129

Appendix In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the YCbCr color difference. In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the YPbPr color difference.
Page 130: General Notes

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Page 131: Precautions When A Using Laser Device

If an error occurs in the projector, turn off the power immediately, unplug the projector from the outlet, and contact your local dealer or the nearest Epson repair center. Continuing to use it in an error condition may result in an electric shock, fire, or visual impairment.
Page 132: Laser Optical Path

When lens shift is at the maximum horizontal position: 34° from the center of the lens General Notice EPSON is a registered trademark, EXCEED YOUR VISION, ELPLP and their logos are registered trademarks or trademarks of Seiko Epson Corporation. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.
Page 133

Advanced ..........87, 89 Air filter ............113 Air filter cover ..........113 AMX Device Discovery ......... 98 EPSON Super White ........87 Appearance ........... 126 Erase lens position ......... 63, 95 Aspect ............35, 88 Erase memory .......... 66, 95 Auto setup ............
Page 134

Index Image menu ............ 86 Panel alignment ..........94 Image processing .......... 90 Pattern color ............ 94 Indicators ............101 PC port ............... 22 Info menu ............99 Picture in Picture ........79, 100 Input signal ..........94, 99 PJLink .............. 123 Inverse 3D Glasses .........
Page 135

Index Start adjustments .......... 94 Startup screen ..........94 Status ..............99 Sub menu ............29 Subnet mask ........... 97 Sub-screen ............78 Subscreen position ........100 Subscreen size ..........100 Subscreen source ........100 Super-resolution ........46, 89 Super-resolution/4K ......46, 89 Supported resolutions ......

This manual also for:

Eh-ls9600w

Epson EH-LS10000 User Manual

Also See for Epson EH-LS10000

Related Manuals for Epson EH-LS10000

Summary of Contents for Epson EH-LS10000

This manual also for:

Comments to this Manuals

Latest comments: