Organization of the Guide and Notations in the Guide Using Each Guide The guides for this projector are organized as shown below. Safety Instructions/Support and Service Guide Contains information on using the projector safely, as well as a support and service guide, troubleshooting check lists, and so on.
Organization of the Guide and Notations in the Guide Notations Used in This Guide Safety Indications The User's Guide and the projector use graphical symbols to show how to use the projector safely. The following shows the symbols and their meanings. Please understand and respect these caution symbols in order to avoid injury to persons or property.
Preparing Part Names and Functions Front/Top Name Function a Indicators The color of the indicators and whether they are flashing or lit indicate the status of the projector. p.10 b Control panel Retractable control panel on the side of the projector. p.10 c Front adjustable foot Adjust the projector's horizontal tilt when placing and projecting.
Preparing Name Function g Air exhaust vent Exhaust vent for air used to cool the projector internally. Caution While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent.
Preparing Interface Name Function a HDMI1/HDMI2 ports Connects HDMI compatible video devices and computers. p.21 b Cable holders Insert the supplied HDMI cable clamp. Because thick HDMI cables with a large outer diameter, may disconnect easily due to the weight of the cable, secure the cables with the HDMI cable clamp.
Preparing Base Name Function a Air intake vent When suspending from a ceiling, install the projector so that dust does not collect in the vent. b Screw holes for ana- Screw holes for attaching the anamorphic lens. morphic lens Front adjustable foot Adjust the projector's horizontal tilt when placing and projecting.
Preparing Control Panel Buttons/Indicators Function Flashes orange if the internal temperature is too high. Shows the projector's errors through a combination of other indicators lit and flashing. p.101 Lit orange when an error occurs in the laser section. Shows the projector's errors through a combination of other indicators lit and flashing.
Preparing Buttons/Indicators Function Move vertically and horizontally to select the adjustment value for the Config- uration menu item. p.29 Move vertically while projecting an image to correct keystone distortion. p.34 When the Configuration menu is displayed, it accepts and enters the current selection and moves to the next level.
Preparing Remote Control Top section buttons EH-LS10000 EH-LS9600W Button Function Turns the projector on. p.27 Turns the projector off. p.28 The remote control buttons light up for approximately 10 seconds. This is useful when operating the remote control in the dark. Temporarily hides or shows the image.
Preparing Button Function Performs operations such as play and stop for connected devices that meet the HDMI CEC standards. p.60 Displays the HDMI link settings menu. p.60 Adjusts the volume for connected devices that meet the HDMI CEC standards.
Preparing Middle section buttons Button Function Changes the adjustment item for the motorized lens function. The following adjustment items are available. • Focus s p.32 • Zoom s p.33 • Lens shift s p.33 Changes the Color Mode. p.44 Changes between 2D and 3D images. p.39 Selects the Configuration menu items and adjustment values.
Preparing Bottom section buttons EH-LS10000 EH-LS9600W Button Function Saves, loads, or erases a memory, and allows you to change the name of a memory. p.64 Loads the lens position. p.63 Changes the 3D format. p.39 Reduces the jarring effect caused by quick movements by interpolating frames, and adjusts to render a smoother, clearer image.
Preparing Installing Notes on Installing Warning Ceiling mount installations • A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury. •...
Preparing How to Install The projector can be installed using a variety of methods, such as placing on a shelf or suspending from a ceiling. Using the lens shift function gives you more flexibility to place the projector where you want. p.33 Placing on a shelf and projecting You can install the projector in an AV rack or on a shelf in your living room to project images.
Preparing Projection Distance and Lens Shift Maximum Values The size of the projection increases as the projector is moved away from the screen. Use the following table to setup the projector so that it projects at the optimum size. The values given here are for your reference only. You can also adjust the position by projecting using lens shift.
Preparing Unit: cm 16:9 Projected Image Size Projection Distance (E) Lens Shift Maximum Values W x H Minimum Maximum Distance Distance Distance (Wide) (Tele) (C, D) 40" 89 x 50 60" 130 x 75 80" 180 x 100 100" 220 x 120 120"...
Preparing Connecting a Device Attention • Make cable connections before connecting to a power outlet. • Check the shape of the cable's connector and the shape of the port, and then connect. If you force a connector of a different shape into the port, it could cause damage and a malfunction to occur. Removing the Cable Cover You can attach the cable cover to the rear of this projector to give it a clean and smooth look.
Preparing Connecting Video Devices To project images from Blu-ray disc players or video recorders and so on, connect to the projector using one of the following methods. • Depending on the video device, there may be multiple types of output available. Check the documentation supplied with the video device to confirm the output types.
Preparing Connecting a Computer To project images from a computer, connect the computer using one of the following methods. Computers with an RGB output port Computers with an HDMI output port To prevent the weight of the HDMI cable disconnecting it from the port, make sure you secure it to the cable holder with the HDMI cable clamp.
Preparing Connecting WirelessHD devices (EH-LS9600W only) The projector receives transmissions from the WirelessHD Transmitter, and projects the images. p.67 Change the projected image by pressing the button on the remote control or the button on the control panel. • When receiving WirelessHD images, make sure WirelessHD is set to On. Settings - WirelessHD - WirelessHD p.91...
Preparing Connecting to the LAN port Connect to a network router, a hub, and so on, with a 100BASE-TX or 10BASE-T LAN cable. You can operate the projector or check its status over a network from a computer or a smart device. •...
Preparing Preparing the Remote Control Installing Batteries Attention • Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way. • You cannot use other batteries except for the AA size manganese or alkaline. Remove the battery cover.
Preparing The operation range for the WirelessHD Transmitter differs. p.75...
Basic Operations Turning the Projector On and Off Turning On Warning • Do not allow small children to make operations. If children do make operations, they must be accompanied by an adult. • Do not look into the lens during projection. Also, do not look into the lens using optical devices (such as a magnifying glass or telescope).
Basic Operations • To obtain stable image quality, it is recommended that you leave the projector on for a while before starting operations. • This projector provides a Child Lock function to prevent children from accidentally turning the power on and a Control Panel Lock function to prevent accidental operations. Settings - Lock Setting - Child Lock/Control Panel Lock p.91...
Basic Operations Configuration Menu Operations Using the Configuration menu, you can make adjustments and settings for images or image quality. • For items adjusted using an adjustment bar, such as the brightness level, you can press the button while the adjustment screen is displayed to return the adjustment value to its default value. •...
Basic Operations Press the button to exit the menu.
Basic Operations Adjusting the Projected Screen Displaying the Test Pattern Immediately after installation, a test pattern is used to adjust the zoom, focus, and the projection position. Press the button on the remote control to display the test pattern. EH-LS10000 EH-LS9600W You can also select patterns that display R (red), G (green), and B (blue) individually, as well as the pattern for adjusting the display position.
Basic Operations The adjustment items switch as shown in the following table. Focus adjustment Adjust Focus is displayed on the screen. Adjusts the focus of the projected image. p.32 Zoom adjustment Adjust Zoom is displayed on the screen. Adjusts the size of the projected image. p.33 Lens shift adjustment Adjust Lens Shift is displayed on the screen.
Basic Operations Adjusting the projection size (zoom adjustment) Press the buttons to adjust the size of the projected screen. Adjusting the position of the projected image (lens shift) If the projector cannot be setup in front of the screen, you can adjust the position of the image by using lens shift.
Basic Operations Keystone You can use the button on the control panel to correct keystone distortion. Move the button up or down to display the adjustment gauges. When the gauges are displayed, move the button up or down to perform vertical correction. When the top or bottom is too wide •...
Basic Operations Aspect You can change the input signal's type, aspect ratio, and resolution to match the Aspect of the projection screen. The available Aspect varies depending on the image signal currently being projected. Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected image for commercial purposes or for public viewing may infringe upon the rights of the copyright holder of that image based on copyright law.
Basic Operations Input Image Setting Name (Aspect) Normal Full Zoom Notes Matches the vertical size Uses the entire projection Retains the aspect ratio of of the projection panel. panel. the input signal, and The aspect ratio differs matches the horizontal depending on the input size of the projection pan- image.
Charging • When charging, connect the supplied cable to the USB port designated by Epson. Do not charge using other devices as it may cause the battery to leak, overheat, or explode. • Only use the supplied charging cable to charge the 3D Glasses. Otherwise, it could overheat, ignite, or explode.
Basic Operations Caution Wearing 3D Glasses • Make sure you wear the 3D Glasses correctly. Do not wear the 3D Glasses upside down. If the image is not displayed correctly into the right and left eyes, it could cause you to feel unwell. •...
Basic Operations Caution Health risks • You should not use 3D Glasses if you are sensitive to light, have a heart condition, or are unwell. Doing so could aggravate your pre-existing conditions. Caution Recommended age of use • The minimum recommended age to view 3D images is six years old. •...
Basic Operations • For details on 3D format settings on the AV device, see the documentation supplied with the AV device. • When the 3D format has not been set up correctly, the same image is split horizontally or vertically and is not projected correctly as shown below.
Basic Operations Charging the 3D Glasses The following charging methods are available, depending on the model of 3D Glasses being used. If you have a WirelessHD Transmitter, you can use it to charge the glasses. If you do not have a WirelessHD Transmitter, you can charge by using an optional USB Charging Adapter. Charging using the WirelessHD Transmitter Charging using the USB Charging Adapter Use the USB cable to connect the 3D Glasses to...
Basic Operations Wearing and viewing with the 3D Glasses Turn on the 3D Glasses by sliding the Put on the 3D Glasses and enjoy the [Power] switch to On. show. The indicator turns on for several seconds, • When you have finished using the and then turns off.
Basic Operations Converting 2D Images to 3D Images and Viewing You can convert 2D images to 3D images from HDMI1, HDMI2, or WirelessHD (EH-LS9600W only). Press the button, select Signal - Select the strength of the 3D effect, and then press the button to 3D Setup from the Configuration menu, and then press the...
Setting Image Quality Basic Color Mode You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the image varies depending on the mode selected. Press the button. You can make settings from the Configuration menu. Image - Color Mode p.86 Select Color Mode.
Setting Image Quality The following color modes are available. Available Grayed out and unavailable Mode Projected Application Image Dynamic Ideal for use in a bright room. Projects a vivid, bright image. Living Room Natural Ideal for use in a dark room. It is recommended that you per- form color adjustment in this mode.
Setting Image Quality Super-resolution This function is only available for EH-LS9600W. This setting sharpens blurred images, enhancing the apparent detail of the image by increasing the resolution of the image signal. Press the button. Use the buttons to make adjustments. The higher the number, the stronger the effect.
Setting Image Quality Press the button. • You can make settings from the Configuration menu. Signal - Super-resolution/4K p.88 • This cannot be set when a computer image signal is being input. • This cannot be set when converting 2D images to 3D images. Signal - 3D Setup - 2D-to-3D Conversion p.88...
Setting Image Quality Detail Enhancement This function enhances details in an image to create clear outlines. Press the button, select Signal - Use the buttons to Detail Enhancement from the select Strength, and then use the Configuration menu, and then press buttons to make the adjustments.
Setting Image Quality Press the button, select Image Use the buttons to select the item, and then press the - Dynamic Contrast from the button to confirm the selection. Configuration menu, and then press button to confirm the selection. The Dynamic Contrast adjustment screen is displayed.
Setting Image Quality Precise Image Adjustment Hue, Saturation, and Brightness You can adjust the hue, saturation, and brightness for each of the R (red), G (green), B (blue), C (cyan), M (magenta), and Y (yellow) colors. Adjusts the overall color of the image to be blue, green, or red. Adjusts the overall vividness of the image.
Setting Image Quality Gamma You can adjust slight coloration differences that may occur due to the device being used when the image is displayed. You can use one of the following three methods selected from the Configuration menu. Setting Method Menu Settings Select and adjust the correction val- Image - Advanced - Gamma...
Setting Image Quality Adjust using the gamma adjustment graph Make adjustments while viewing the gamma adjustment graph for the image being projected. Use the buttons to Use the buttons to select the adjust the brightness, and then press part you want to adjust from the button to confirm the graph.
Setting Image Quality Color Temp. You can adjust the color temperature. Make adjustments if the image is a little too blue or too red. The menu is displayed in the following order. Image - Color Temp. Use the buttons to make adjustments. Blue tints grow stronger as the value is increased, and red tints grow stronger as the value is reduced.
Setting Image Quality Press the button, select Image - Press the button to exit the menu. Sharpness from the Configuration menu, and then press the button to confirm the selection. The Sharpness adjustment screen is displayed. Select Advanced at the top right of the screen, and then press the button to confirm the selection.
Setting Image Quality Lens Iris Reduces the amount of light in the projection lens and adjusts the brightness of the image. Unlike dynamic contrast that automatically adjusts the amount of light according to the brightness of the image, this allows you to adjust the amount of light for images with a lot of bright scenes. Press the button to exit the Press the...
Setting Image Quality Panel Alignment Adjusts the pixel color shift of the LCD display. • When projecting using lens shift to adjust the position of the image, once you have adjusted to a suitable position, perform panel alignment. p.33 • Panel alignment cannot be performed correctly when projecting using extreme keystone correction.
Setting Image Quality After adjusting four corners, select Press the button to exit the menu. Exit, and then press the button to confirm. If the four corners still need adjustments, select Select intersection and adjust, and then continue adjustments.
Setting Image Quality Image Processing Improves the image quality or response speed for projected images. This is only available when receiving a progressive signal input from the Component, Video, HDMI1, or HDMI2 ports, or from WirelessHD. Press the button to exit the Press the button, select Signal - menu.
Setting Image Quality Color Gamut Allows you to easily set the color gamut to match the standard for the video devices being used. This can be set when Color Mode is set to Natural. Select the item according to the Press the button, select Image - device being used.
Useful Functions HDMI Link HDMI Link Function When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI1/HDMI2 ports, you can perform linked operations such as linked power on and volume adjustment for the AV system from one remote control.
Useful Functions • To use the HDMI Link function, you must configure the connected device. See the documentation supplied with the connected device for more information. • When using the WirelessHD Transmitter, make the following settings when you want to use the power on/off link function (EH-LS9600W only).
Useful Functions Lens Position Function You can save the focus, zoom, and lens shift positions for lens adjustment. This allows you to load a saved lens position to quickly set the lens to the optimum projection position. For example, you can easily load a lens position that was saved while projecting on a cinema scope screen, or when multiple screens with different aspects were being used.
Useful Functions Loading the Lens Position Press the button, and then select Load Lens Position. The Load Lens Position screen is displayed. Select the lens position name you want to load. The zoom, focus, and lens shift are adjusted to the status you saved. While adjustments are being performed, a message is displayed and the projector cannot be operated.
You can save the following Configuration menu settings. Color Mode, Power Consumption, Brightness, Contrast, Color Saturation, Tint, Sharpness, Image Color Temp., Skin Tone, Dynamic Contrast p.86 Advanced Sharpness, Offset, Gain, Gamma, Hue, Saturation, Brightness, EPSON Super White Deinterlacing, Motion Detection, Super-resolution , Super-resolution/4K , Detail Enhance- Signal ment p.88...
Useful Functions Use the buttons to select the memory name to be saved, and then press the button to confirm the selection. The current projector settings are saved as a memory. If the mark on the left of the memory name is turned green, it means the memory has already been registered.
Useful Functions Erasing the Saved Memory Press the button, and then select Erase Memory. The Erase Memory screen is displayed. Select the memory name you want to erase. A confirmation message is displayed. Select Yes to erase the content of the saved memory. You can erase all of saved memories from Reset - Reset Memory on the Configuration menu.
Useful Functions Connecting with WirelessHD (EH-LS9600W Only) Installing the WirelessHD Transmitter You can use the supplied WirelessHD Transmitter to wirelessly receive image data. This is useful when the projector cannot be setup near your AV devices as you can connect the devices to the projector without using cables.
Useful Functions WirelessHD Transmitter part names Front Rear Name Function button Turns the WirelessHD Transmitter on or off. This performs the same function as the button for WiHD Transmit- ter on the lower section of the remote control. b Input button Changes to the image from each input port.
Useful Functions WirelessHD Transmitter connection example and signal flow Connection example 1: Viewing without an AV amplifier Connect a device to WirelessHD Transmitter without using an AV amplifier, and connect the sound bars and so on to the Optical Audio-Out port to output audio. When outputting audio from a connected device, you need an optical digital audio cable.
Useful Functions Connection example 2: Viewing with a connected AV amplifier The audio from the device connected to the AV amplifier is output from the amplifier's audio-out port without passing through the WirelessHD Transmitter. When outputting audio from a device connected with an MHL cable, you need an optical digital audio cable. The audio output method to an AV amplifier may be restricted by the specifications of the monitor device, such as a television, connected to the Output port.
Useful Functions Setting the WirelessHD Transmitter Set up the WirelessHD Transmitter Using an HDMI cable, connect the AV connected to the projector so that device you want to use to the Input they are facing each other. p.74 port on the WirelessHD Transmitter. You can connect up to five AV devices.
Useful Functions Projecting Images Start playback on the AV device, and then turn on the projector and the WirelessHD Transmitter. indicator on the WirelessHD Transmitter turns on. Check the status of the WiHD indicator on the WirelessHD Transmitter. If the WiHD indicator is on, go to the next step. If the indicator is off, press the button on the remote control or the WirelessHD Transmitter.
Useful Functions If projection does not start, press the button on the remote control to change the source. Make sure you point the remote control at the projector when using the button on the remote control. Projection starts. When connecting two or more AV devices to the WirelessHD Transmitter, press the button to switch images.
Useful Functions Function Explanation Reset Resets WirelessHD settings to their default settings. Even when the WirelessHD Transmitter and the projector are connected, 0% is displayed as the Reception when no image signal is being input. Check the communication status using the Link indicator.
Useful Functions • The wireless transmission range varies depending on the placement and material of the surrounding furniture and walls. The values given here are for your reference only. • The projector cannot communicate through walls. • Place the WirelessHD Transmitter on a wooden shelf or other location that does not block the signal from being transmitted from the front of the device.
Useful Functions Point the remote control at the WirelessHD Transmitter, and then press the button. Remote control WirelessHD Transmit- Depending on the output target, the WiHD indicator on the WirelessHD Transmitter indicates the following status. On: The image is being output to the projector. Off: The image is being output to the monitor device.
Useful Functions Point the remote control at the The target screen changes each time WirelessHD Transmitter, and then you press the button. press the button. Remote control WirelessHD Trans- mitter Displays the sub-screen (small screen) for the connected device. The screen that is not receiving an image signal is displayed in blue or black.
Useful Functions Displaying as a Sub-Screen Point the remote control at the To close the sub-screen, press the WirelessHD Transmitter, and then button again. press the button. The projected image is switched. • When the sub-screen is displayed, press the button to switch the image for the sub- screen.
Useful Functions Picture in Picture In Picture in Picture, two different image sources can be projected, one in the main screen (large screen) and the other in the sub screen (small screen). Types of Screen that can be Displayed Simultaneously HDMI1, HDMI2 and WirelessHD are examples of input sources that can be displayed in Picture in Picture.
Useful Functions Picture in Picture Settings Use the Picture in Picture menu to change the size or position of the sub screen. Press the button, select Make settings for each of the displayed functions. Settings - Picture in Picture from the Configuration menu, and then press button to confirm the selection.
Useful Functions Operations and Settings Using the Network When the projector is connected to a network, you can make settings and control the projector from a computer or smart device over the network. Making Settings and Performing Operations from a Web Browser When a computer or smart device with a Web browser is connected to the same network as the projector, you can change the projector's settings in the same way as operating a remote control.
Useful Functions Displaying the Web Control screen on your smart device Start the Web browser, and then enter the IP address of the projector in the address input box of the Web browser. The remote and config icons are displayed in your Web browser. Tap the config icon.
Useful Functions Displaying the Web Remote screen on your smart device Start the Web browser, and then enter the IP address of the projector in the address input box of the Web browser. The remote and config icons are displayed in your Web browser. Tap the remote icon.
When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent. Subject: EPSON Projector Line 1: The projector name where the problem has occurred Line 2: The IP address set for the projector where the problem has occurred Line 3 and on: Details of the problem The details of the problem are listed line by line.
Useful Functions Message Contents Remedy Internal error Internal error Handling errors or warnings is the same as checking the status of the indicators. Laser driver error p.101 Fatal error Lens cover error Fan related error Fan error Sensor error Sensor error Light sensor error Cinema Filter Error Cinema filter error...
Configuration Menu Configuration Menu Functions Configuration Menu Table If there is no image signal being input, you cannot adjust items related to the image or signal in the Configuration menu. Note that the items displayed for the image, the signal, and other information vary depending on the image signal being projected.
Bright- ness for each R, G, B, C, M, and Y color. ness p.50 EPSON Super White On, Off (This can only be set when the Color Mode is set to Natural, THX, Cinema, Adobe RGB, Digital Cinema, 3D Cine-...
Configuration Menu Signal menu Function Menu/Settings Explanation *1 *2 3D Setup 3D Display On, Off Enables or disables the 3D image display func- tion. p.39 2D-to-3D Conver- Off, Weak, Medium, Sets the strength of the 3D effect when convert- sion Strong ing 2D images to 3D images.
Configuration Menu Function Menu/Settings Explanation Frame Interpo- Off, Low, Normal, High Reduces afterimages when projecting moving *2 *6 images by interpolating between one frame and lation the next. p.49 Super-resolu- 0 - 5 (EH-LS9600W only) tion Reduces blurring that occurs at the edge of im- ages when the resolution is increased.
HDMI1 or HDMI2 ports, or from WirelessHD. This may be automatically set to Off or 8% depending on the input signal. HDMI Video Auto, Normal, Ex- (This can only be set when EPSON Super *1 *3 Range panded White is set to Off.)
Configuration Menu Settings menu Function Menu/Settings Explanation Keystone -60 - 60 Performs vertical keystone correction. p.34 HDMI Link Device Connections - Displays a list of devices connected from the HDMI1 or HDMI2 ports, or from WirelessHD HDMI Link On, Off Enables or disables the HDMI Link function.
Configuration Menu Function Menu/Settings Explanation Lock Setting Lens Lock On, Off When set to On, the focus, zoom, and lens shift settings are locked at their current settings. If you press the button when Lens Lock is set to On, is displayed on the screen.
Configuration Menu Function Menu/Settings Explanation Operation Direct Power On On, Off You can set up the projector so that projection starts as soon as the power cord is plugged in without any button operations. Note that when this is set to On, projection starts if power is restored after a blackout or other power outage and the power cord is still plugged into the projector.
Configuration Menu Function Menu/Settings Explanation Display Menu Position Sets the position where the menu should be dis- played. Menu Color Color 1, Color 2 Selects the color for the Configuration menu. • Color 1 Main menu: Black Selected items: Gray •...
Configuration Menu Function Menu/Settings Explanation Reset Yes, No All adjustment values for Settings are returned to their default settings, except for the following. • Power On Link • Power Off Link • Projection • User Button • Standby Mode • High Altitude Mode •...
Configuration Menu Network menu When you have made network settings for the projector and you connect to a computer or smart device on the network, you can change settings from your Web browser without displaying the Configuration menu, or you can use the computer or smart device as a remote control. Also, when mail notification settings have been made and an error or warning occurs in the projector, a notification email is sent to the email addresses you have specified.
Configuration Menu Function Explanation Web Control Password Set a password to use Web Control. You can enter up to 32 single-byte alpha- numeric characters. (* cannot be used.) Web Control is a function that allows you to change the projector's settings by using the Web browser on a computer or smart device connected to the network.
Configuration Menu Function Menu/Settings Explanation Address 1 Setting Enter the destination email addresses to which to send the notification email, and select the Address 2 Setting problems or warnings you want to be notified Address 3 Setting about. You can register up to three destinations. You can enter up to 64 single-byte alphanumeric characters for the email addresses.
Configuration Menu • Each time the CAPS key is selected and the button is pressed, it sets and changes between upper case and lower case letters. • Each time the SYM1/SYM2 key is selected and the button is pressed, it sets and changes the symbol keys for the section enclosed by the frame.
Configuration Menu Reset menu Function Explanation Reset All Resets all items in the Configuration menu to their default settings. The following items are not reset to their defaults: Input Signal - Component, Panel Alignment, Language, Save Memory, Save Lens Position, and Opera- tion Hours.
• If turning the power back on does not clear the problem, stop using the projector and remove the power plug from the electrical outlet. Contact your local dealer or the Epson Projector Contact nearest Epson repair center. s List...
If the problem does not improve even after trying the solutions mentioned above, stop using the projector and remove the power plug from the electrical outlet. Con- tact your local dealer or the nearest Epson repair center. Epson Projector Contact List...
Troubleshooting Indicator status during normal operation : Lit : Flashing : Off Indicators Status Remedy Standby condition When you press the button on the remote control, or the button on the control panel, projection starts. Standby condition When you press the button on the remote control, or the (Standby Mode is set to button on the control panel, projection starts.
Troubleshooting When the Indicators Provide No Help Check the problem Check the following table to see if your problem is mentioned, and go to the appropriate page for information on handling the problem. Problem Page Problems relating to im- No images appear p.105 ages Projection does not start, the projection area is completely black, or the...
Troubleshooting Problems relating to images No images appear Check Remedy Is the power turned on? Press the button on the remote control or the button on the control panel. Is the power cord connected? Connect the power cord. Are the indicators switched off? Disconnect and then reconnect the projector's power cord.
Troubleshooting "Not supported" is displayed Check Remedy Is the image signal format setting correct? When Video is input If nothing is projected even when Video Signal is set to Auto from the Configuration menu, set the signal that matches the connected device.
Troubleshooting Images are fuzzy or out of focus Check Remedy Has the focus been adjusted? Adjust the focus. p.32 Is the projector at the correct distance? Check the recommended projection range. p.18 Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy.
Troubleshooting Image colors are not right Check Remedy Is the image signal format setting correct? When Video is input If nothing is projected even when Video Signal is set to Auto from the Configuration menu, set the signal that matches the connected device.
If the problem continues, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest projector information Epson Projector Contact List center. Problems with the remote control The remote control does not respond...
Troubleshooting Check Remedy Are the batteries dead or have the batteries Make sure the batteries are inserted correctly or replace the bat- been inserted correctly? teries with new ones if necessary. p.25 Is the remote control pointed at the Wire- Make sure you point the remote control at the WirelessHD Trans- lessHD Transmitter when operating the WiHD mitter when using the WiHD Transmitter buttons on the remote...
Troubleshooting The 3D image is enlarged and truncated Check Remedy Is the correct 3D video format set? Video may be truncated if an incorrect 3D format is set. Set the correct 3D format. p.37 Problems with HDMI HDMI Link does not function Check Remedy Are you using a cable that meets the HDMI...
Troubleshooting Check Remedy Are signals being received within the Wire- Check the Wireless HD transmission range, and view within that lessHD transmission range? range. p.74 Is the supplied WirelessHD Transmitter Check the indicator on the WirelessHD Transmitter. If there is turned on? no power being supplied, make sure the connector for the AC adapter is securely connected, and then turn on the power...
Maintenance Maintenance Cleaning the Parts You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate. Warning Do not use sprays that contain flammable gas to remove dirt and dust from the projector's air filter, and so on.
Maintenance Remove the air filter. Remove any dust remaining on the air filter by using a vacuum cleaner from Grip the knob in the center of the air filter the front side. and pull it out at an angle. Hold the air filter with the surface Replace the air filter if a message is facing down and tap it 4 or 5 times to displayed even after cleaning the...
• Do not touch the projection lens. When cleaning the lens, contact your local dealer or the nearest projector Epson Projector Contact List information center. Cleaning the 3D Glasses Clean the lenses of the glasses by wiping them gently with a soft cloth.
Appendix Optional Accessories and Consumables The following optional accessories/consumables are available for purchase if required. This list of optional accessories/consumables is current as of: 2014.1. Details of accessories are subject to change without notice. Varies depending on country of purchase. Optional Items Name Model No.
Appendix Computer Signals (Analog RGB) Signal Refresh Rate (Hz) Resolution (dots) 60/72/75/85 640 x 480 SVGA 56/60/72/75/85 800 x 600 60/70/75/85 1024 x 768 SXGA 70/75/85 1152 x 864 60/75/85 1280 x 960 60/75/85 1280 x 1024 WXGA 1280 x 768 1366 x 768 60/75/85 1280 x 800...
Appendix Notes on Transportation There are many glass parts and precision components inside the projector. To prevent damage due to impacts when transporting, handle the projector as follows. Moving Nearby Before carefully moving the projector, make sure it has been turned off and all cables have been disconnected. Attention •...
Appendix Specifications Product name EH-LS10000 EH-LS9600W Appearance (not including adjustable 550 (W) x 225 (H) x 553 (D) mm foot) Panel size 0.74" wide Display method Polysilicon TFT active matrix Resolution 1920 (W) x 1080 (H) x 3 Focus adjustment Motorized Zoom adjustment Motorized (approx.
If you use the projector tilted at an angle of more than 3°, it could be dam- aged or cause an accident. ESC/VP21 commands Use of ESC/VP21 enables control of the projector from an external device. For more details, see the following Web site. http://www.epson.com RS-232C cable layouts • Connector shape: D-sub 9-pin (male) •...
HDMI1 INPT 32 HDMI2 INPT 33 WirelessHD INPT 34 Component INPT 24 Video INPT 21 INPT 11 EH-LS9600W only Manufacturer name displayed for "Manufacture name information query" EPSON Model name displayed for "Product name information query" EPSON 10000 EPSON 9600...
DECLARATION of CONFORMITY According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers Epson America, Inc. Located at: 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806...
Appendix Indication of the manufacturer and the importer in accordance with requirements of directive 2011/65/ EU (RoHS) Manufacturer: SEIKO EPSON CORPORATION Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan Telephone: 81-266-52-3131 Importer: SEIKO EUROPE B.V. Address: Azië building, Atlas ArenA, Hoogoorddreef 5, 1101 BA Amsterdam Zuidoost The Netherlands...
Appendix Glossary This section briefly explains the difficult terms that are not explained in context in the text of this guide. For details, refer to other commercially available publications. The ratio between an image's length and its height. Screens with a horizontal:vertical ratio Aspect Ratio of 16:9, such as HDTV screens, are known as wide screens.
Appendix In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the YCbCr color difference. In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the YPbPr color difference.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
If an error occurs in the projector, turn off the power immediately, unplug the projector from the outlet, and contact your local dealer or the nearest Epson repair center. Continuing to use it in an error condition may result in an electric shock, fire, or visual impairment.
When lens shift is at the maximum horizontal position: 34° from the center of the lens General Notice EPSON is a registered trademark, EXCEED YOUR VISION, ELPLP and their logos are registered trademarks or trademarks of Seiko Epson Corporation. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.
Advanced ..........87, 89 Air filter ............113 Air filter cover ..........113 AMX Device Discovery ......... 98 EPSON Super White ........87 Appearance ........... 126 Erase lens position ......... 63, 95 Aspect ............35, 88 Erase memory .......... 66, 95 Auto setup ............
Index Image menu ............ 86 Panel alignment ..........94 Image processing .......... 90 Pattern color ............ 94 Indicators ............101 PC port ............... 22 Info menu ............99 Picture in Picture ........79, 100 Input signal ..........94, 99 PJLink .............. 123 Inverse 3D Glasses .........
Index Start adjustments .......... 94 Startup screen ..........94 Status ..............99 Sub menu ............29 Subnet mask ........... 97 Sub-screen ............78 Subscreen position ........100 Subscreen size ..........100 Subscreen source ........100 Super-resolution ........46, 89 Super-resolution/4K ......46, 89 Supported resolutions ......