Page 2
Hitachi, Ltd. Hitachi, Ltd., reserves the right to make changes to this document at any time without notice and assumes no responsibility for its use. This document contains the most current information available at the time of publication.
System requirements and specifications..............2-2 3 Planning for TrueCopy................3-1 Storage system preparation..................3-2 Cache, additional control memory requirements..........3-2 Workflow for adding and removing cache memory........3-3 Workflow for adding control memory............3-3 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 4
Volume types that can be shared with TrueCopy............4-2 Data Retention Utility....................4-4 Dynamic Provisioning ..................... 4-5 LUN Manager ......................4-6 Performance Monitor....................4-6 Universal Replicator ....................4-7 ShadowImage......................4-7 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 5
Planned outage of the secondary system or remote path........7-20 Planned outage of both primary and secondary systems........7-21 8 Data migration..................8-1 Migration overview....................8-2 Migrating data....................8-2 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Corrected the port topology information for extender connection (changed "FC-AL" to "Point-to-Point") (Extender connection on page 3-32). • Updated the description of system option mode (SOM) 689 (System option modes on page 3-4). Preface Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
F600, F800 storage systems, unless otherwise noted. F400, F600, F800 (VSP F400, F600, F800) VSP Fx00 models VSP F series This document uses the following typographic conventions: Preface Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 12
Calls attention to important or additional information. Provides helpful information, guidelines, or suggestions for performing tasks more effectively. Important Provides information that is essential to the completion of a task. Preface Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
1 EB 1,024 PB or 1,024 bytes Accessing product documentation Product documentation is available on Hitachi Data Systems Support Connect: https://support.hds.com/en_us/documents.html. Check this site xiii Preface Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Include the document title and number, including the revision level (for example, -07), and refer to specific sections and paragraphs whenever possible. All comments become the property of Hitachi Data Systems Corporation. Thank you! Preface Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The secondary storage system is connected to the primary storage system using dedicated data paths. TrueCopy supports TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 17
TrueCopy configuration and pair operations as well as disaster recovery operations. The following figure shows the TrueCopy system components. TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
When split, new data is sent to the P-VOL but not the S-VOL. Note: It will continue writing to P-VOL but copying to S-VOL stops so that pair will not be synchronized. TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Device Manager - Storage Navigator, which is a browser-based interface from which TrueCopy is set up, operated, and monitored. The GUI provides the simplest method for performing operations, requiring no previous experience. TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The update operation copies host updates to the S-VOL at the same time that they are copied to the P-VOL. TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
P-VOL and copied to the S-VOL. Subsequent updates are held until the current update is completed in both volumes. This keeps the pair synchronized. TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
SMPL, and then the primary storage system detects the removal of the pair at the secondary system (if the path is normal), the primary storage system changes the status of the P-VOL to PSUS. TrueCopy overview Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
TrueCopy system that require attention before setting up and using TrueCopy. □ System requirements and specifications Requirements and specifications Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
VSP Gx00 models or VSP Fx00 models for both primary and secondary sites. For more information, contact Hitachi Data Systems customer support. Requirements and specifications Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 25
Path group Group of remote paths, which allows you to configure multiple paths at the same time. Requirements and specifications Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 26
You cannot use the system LU for Hitachi NAS Platform as a pair volume. Planning pairs and pair volumes on page 3-8 for more information. Requirements and specifications Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 27
A command device is required for each CCI instance. ¢ See the Command Control Interface User and Reference ¢ Guide for information about setting up and using CCI. Requirements and specifications Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 28
Requirements and specifications Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
□ System performance considerations □ Planning pairs and pair volumes □ Consistency group planning □ Host failover software □ Data path requirements and configurations Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Note: Neither cache nor control memory can be added to or removed from the storage system when pair status is COPY. When either of these tasks is to Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
VSP G400, G600, G800: Control memory is added in Extension4. Identify the status of all volumes. If a volume is used by a TrueCopy pair, delete the TrueCopy pair. Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The following table lists and describes the system option modes related to TrueCopy operations. For a complete list of all SOMs, see the Hardware Guide for your storage system model. Work with your Hitachi Data Systems team to make sure the appropriate SOMs are set on your storage system.
Example of significant difference between the two: 1ms RT Time and 500ms remote IO response time. Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 34
Therefore, you need to double the round trip time. • For the "round trip time" in the formula, please ask Hitachi Data Systems customer support, or use a ping command. If you do not use channel extenders between the primary and secondary systems, specify "1".)
With the Fence Level setting (specified during the initial copy), you decide whether, when the pair is split due to an error, the host Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Options and settings for number of pairs copied, and their priority, during the initial copy and resync operations. See Priority for initial copy operations and scheduling order on page 3-15 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Relative Primary Volume. The difference is calculated between the ¢ LDEV numbers of two successive P-VOLs. S-VOLs are assigned according to the closest LUN number. Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
This setting reduces the amount of time required to analyze the consistency of S-VOL data with the P-VOL during disaster recovery efforts. 3-10 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Although CCI allows you to specify track or cylinder, the VSP G200, G400, G600, G800 and VSP F400, F600, F800 storage systems use only tracks, whether you specify track or cylinder, or if you do not specify either of them.
The P-VOLs are for the new pairs. P-VOL Value set for Initial Copy Priority LUN 10 LUN 11 3-15 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
This topic describes how to create, update, and copy TC pairs in a consistency group of one primary storage system and one secondary storage system. 3-16 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
This topic describes how to create, update, and copy TC pairs in a consistency group of multiple primary storage systems and secondary storage systems. 3-17 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 46
Figure notes: CCI uses a consistency group that consists of multiple primary and secondary storage systems. 3-18 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Create CCI configuration definition file C for a configuration of multiple pairs of storage systems. In CCI, register pairs to a consistency group, and resume pair operation using CCI configuration definition file C. 3-19 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
3-12 for the maximum number of consistency groups and the maximum number of TC pairs you can create. 3-20 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
A split command is in progress • The host requested I/O processing • The microprocessor of the connection destination port for the I/O request is blocked 3-21 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Reference. • The CCI settings for TC are optional. The following tables show the effects of the settings on read and write access. 3-22 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In Device Manager - Storage Navigator, pairs are automatically ¢ assigned to CTG 127 when the pairs are created and function switch 30 is On. 3-23 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Remote I/O (RIO), which is issued during the change to PSUE status, is accepted by the secondary system. • When a pair's status is changing to PSUE: 3-24 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use the same protocol for the data paths between the host and storage system and between the primary and secondary storage systems. When 3-25 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Greater than 30 km (18.6 Communications lines are Approved third-party required. channel extender miles) products. TrueCopy operations typically do not exceed 30 km. 3-26 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Selective ACK: Make sure Selective ACK is enabled for iSCSI ports. Selective ACK is set to Enable by default (Edit Ports window). Do not change this setting. 3-27 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 56
As a result, performance might be greatly affected. Use Fibre Channel data paths for critical systems that require high performance. 3-28 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The firmware supporting these functions must be installed on both the primary and secondary systems. Direct connection The following figure shows a direct connection, in which two devices are connected directly together. 3-29 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The following figure shows a switch connection, in which up to three optical fibre cables are connected using switches. Two switches can be used. 3-30 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
• Gather several remote copy paths in one location. If you are using a Hitachi switch to make the connection, contact Hitachi Data Systems customer support. Caution: Make sure that the channel extender supports remote I/Os.
Page 61
When you set up secondary-to-primary data paths, specify the same combination of CUs or CU Free, and the same path group ID, as specified for the primary-to-secondary paths. 3-33 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 62
3-34 Planning for TrueCopy Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
ShadowImage (SI) P-VOL in PSUS (Delete pair to RCU) status P-VOL in COPY(RS-R)/RCPY status SI P-VOL is also used as a UR P-VOL or S- Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 65
P-VOL, volume is an S-VOL, volume migration volume migration will stop.) will stop.) Source volume (after volume migration is finished) Target volume Notes: Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Volume Migration migration plan. Before creating the TC pair, delete the SI pair, or disable the Volume Migration setting. After the pair is created, re-create the pair or migration plan. Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Identify the optimum timing for performing TC operations. • Determine the best locations for the TC S-VOL (for example, parity groups with less-frequently accessed volumes to avoid bottlenecks of backend activity). Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
For information about the Quick Restore operation, see the Hitachi ShadowImage® User Guide. Configurations with ShadowImage P-VOLs TC can share a SI P-VOL in three configurations: Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 70
TC P-VOL takes a longer time than normal. This is especially true when the SI pair is in the PSUS(SP)/PSUS status and is caused by the SI copying process. Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 71
Both the TC P-VOL and S-VOL function as SI P- VOLs, providing multiple copies at the local and remote sites. Figure 4-3 Shared TC P-VOL, S-VOL with multiple SI P-VOLs Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
PAIR status, split the SI pair, and then set it in the PSUS status. The following table shows possibilities of TC pair operations according to the SI S- VOL status. 4-10 Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Device Manager - Storage Navigator displays the status of all S-VOLs. The following table shows when data is current on a shared TC/SI volume based on the pair statuses. 4-11 Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Volume Migration volume: • Set I/O rates less than 50 IOPS while migrating volumes; if more than 50 IOPS, volumes may not be migrated. 4-12 Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
TC pair operations, specify the physical LDEV ID of the volume. You cannot delete the virtual LDEV ID of the volume used in TC. 4-13 Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 76
4-14 Sharing TrueCopy volumes Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Device Manager - Storage Navigator. Make sure to complete the procedure. If you cancel remote path settings, you will be unable to perform operations and check status. TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 79
In the Connections (To) tab, click Add Remote Connection. In the Remote Storage System box, specify the following: For Model, select the storage system model. For Serial Number, select the serial number. TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Monitoring is less than 40 seconds, the path might be blocked due to a delay in the network such as many switches in a spanning tree protocol (STP) network or a long distance connection. TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 81
In the Storage Systems tree, click Replication. In the Replication window, click Edit Options > Remote Replication. In the Edit Remote Replica Options window, for Copy Type, select TC. TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 82
- When you create or resynchronize a greater number of pairs than you specify in Maximum Initial Copy Activities, the system processes TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 83
In the Confirm window, review the settings and enter a task name in the Task Name box. Click Apply to save your settings in the system. TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 84
TC configuration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
• To view a pair's current status in the GUI, or review status definitions, see Monitoring pair status, license capacity on page 7-2. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In Device Manager - Storage Navigator: Click Storage Systems, and then expand the Storage Systems tree. In the Storage Systems tree, click Replication > Remote Replication. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 88
P-VOLs for pairing, this LUN is the base S-VOL that is assigned to the first P-VOL and from which subsequent S-VOL LUNs are assigned to the list of P-VOLs. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 89
Back again in the Primary Volume Selection box, select the primary volume to be copied first and click Add. The volume and pair information moves to the Selected Pairs table. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the Storage Systems tree, click Replication > Remote Replication. In the Remote Replication window, click the TC Pairs tab, select the pair to be split, and then click Split Pairs. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 91
Disable (default), to cause host input to be rejected by the S-VOL ¢ while the pair is split. For Primary Volume Write, specify whether writing to the P-VOL is enabled while the pair is split. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the TC Pairs tab, click Resync Pairs. In the Resync Pairs window, ensure that the pair to be resynchronized appears in the Selected Pairs table. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 93
The speed of 4 is a fast copy pace, and the host I/O performance ¢ might be degraded. If you enter a number from 5 to 15, the speed of 4 (fast copy pace) is used. TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the Remote Replication window, click the TC Pairs tab, and then select the pairs to be deleted. In the TC Pairs tab, click More Actions > Delete Pairs. 6-10 TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 95
In the Confirm window, review the settings and enter a task name in the Task Name box. Click Apply to save your settings in the system. 6-11 TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 96
6-12 TC pair operations Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
□ Monitoring and maintaining remote connections and paths □ Deleting TrueCopy remote connections □ Managing power-off for systems and network devices Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the TC Pairs tab, click More Actions > View Pair Properties and review Status. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
PAIR. When you split a pair, the system changes the status of the P-VOL ¢ and S-VOL to PSUS. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
S-VOL to PSUS. The primary system detects this and changes P-VOL status to PSUS. CCI shows the S-VOL status as SSUS. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
¢ Split types appear in the Status field on the View Pair Properties window. The following table describes the split types. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
When a split pair is resynchronized, the primary system copies the out of sync P-VOL tracks to the S-VOL as differential data. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
You can review a pair's history of operations, including the operation's description, date and time it took place, primary and secondary system information, and other details. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The following table describes the operations shown in the History window. Operation Displayed Description Pair Add Start Creation of the pair started. Pair Add Complete Creation of the pair completed. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
- Status: The P-VOL cannot be written to only if the primary system is not able to change S-VOL status to PSUE. Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the LDEVs tab, click More Actions > Force Delete Pairs (TC Pairs). In the Force Delete Pairs (TC Pairs) window, ensure that the volume is in the Selected LDEV table. 7-10 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Monitoring and maintaining remote connections and paths • Viewing remote connection status and path information on page 7-12 • Configuring additional remote paths on page 7-14 7-11 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the Storage Systems tree, click Replication > Remote Connection. Click View Remote Connection Properties to view connection properties and path information. 7-12 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 109
Replication > Remote Connections > Connections (To). Check connections under View Port Condition. Check Status and other details in the Connections (To) tab. 7-13 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the Remote Connections window, click the Connections (To) tab. In the Connections (To) tab, select the remote connection where the remote path is to be added. 7-14 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Determining Minimum Number of Remote Paths on page 3-7 • The interval for data transfer to complete (RIO MIH Time). 7-15 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 112
In the Confirm window, review the settings and enter a task name in the Task Name box. Click Apply to save your settings in the system. 7-16 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In the Remove Remote Paths window, click Remove for the remote paths to be removed. Note that remote paths become unselectable when the minimum number of paths is reached. 7-17 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Hitachi Data Systems customer support. The following topics provide information for planned outages when TrueCopy is present. 7-19 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
When the secondary system is fully powered on and ready, resynchronize the affected pairs at each primary system. Confirm the pair status changes. 7-20 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Power on the primary system, and make sure it is ready to resynchronize operations. If you split any pairs in step 2, you can also resynchronize those pairs now. 7-21 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 118
7-22 Monitoring and maintaining the TC system Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Data migration This chapter discusses using TrueCopy to migrate data from one storage system to another. □ Migration overview Data migration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The volumes are then usually released from the TrueCopy pair. If you need to migrate data from other vendors' storage systems to a VSP G200, G400, G600, G800 or VSP F400, F600, F800 storage system, contact Hitachi Data Systems customer support. Migrating data Make sure that the data path is installed, and TrueCopy configuration procedures are completed.
Page 121
If the original P-VOL is temporarily unavailable for update copy operations, split the new pair so that the new primary system keeps track of changes. Data migration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 122
Data migration Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Disaster recovery This chapter discusses disaster recovery. □ Disaster recovery overview □ Switching operations to the secondary site □ Transferring operations back to the primary site Disaster recovery Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The detection and retrieval process can take some time. Your disaster recovery scenario should be designed so that detection and retrieval of lost Disaster recovery Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
VOLs now the P-VOLs. To switch operations to the secondary site by not deleting pairs Record the pair status and fence level of each S-VOL. Disaster recovery Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Restore the consistency of the S-VOL and update it, if required. The time of suspension indicated on the Last Update Time field of the Detailed Information Disaster recovery Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
At the secondary system create the pairs, with the S-VOLs at the primary site. Make sure to use Entire Volume for the Initial Copy Type option. Confirm that the pairs are created and that status is PAIR. Disaster recovery Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 128
At the secondary system, halt host operations and vary the P-VOL offline. This maintains synchronization of the pairs. Run the horctakeover to the P-VOL command. Vary the primary system and P-VOLs online, and start host operations. Disaster recovery Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
□ Remote path status problems □ Split pair problems □ Troubleshooting using CCI □ Service Information Messages (SIMs) □ Pinned track recovery □ Calling Hitachi Data Systems customer support 10-1 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
SIM is error. generated. If this occurs, call service personnel, and then retry TrueCopy operations after the problem is fixed. 10-2 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
NVS and cache are and secondary fully functional. systems timed out. • Make sure that network relay devices are properly configured and functional. This 10-3 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 132
This timeout occurred. includes cables, connectors, switches, extender devices, communication lines, and all other devices connected to the extenders. 10-4 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
I/O error • Clear any error conditions at the during update copy. In secondary system or S-VOL, and this case, the split type 10-5 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
HOST is the host name. Example: Error codes appear on the right of the equal symbol (=). Review CCI error codes in the following topics. 10-6 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
B990 The pair cannot be created because the consistency group ID is greater than is allowed. If this error occurred when you did not specify the consistency group ID, contact Hitachi Data Systems customer support (see Getting help on page xiv).
The command was rejected because the P-VOL status is other than PSUS (by user) PSUS (because of failure). C21C The command was rejected because the secondary system is not registered, or the registered information is invalid. 10-8 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 137
The TC pair associated with a UR pair cannot be created because the Remote Replication Extended program product is not installed on the primary system. 10-9 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 138
A request for a Paircreate operation was rejected because the specified secondary system is an unsupported product. C32F The number of P-VOL cylinders is not the same or smaller than the number of S-VOL cylinders.) 10-10 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 139
The primary system cache is in the process of being restored. C382 The primary system cache is either in transition to blockage on one side or in the process of being restored on one side. 10-11 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 140
The configuration combination of P-VOL and S-VOL is invalid C3B6 The P-VOL is a SI volume. C3B7 The S-VOL is a SI volume. C3B8 An internal error occurred. 10-12 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 141
Takeover command reversing operations between the P-VOL and S-VOL failed. CB1D No dummy volume can be created in the S-VOL. CB1F The secondary system does not support TC. 10-13 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 142
A UR secondary volume that is in a status other than Suspend. CBDA The Paircreate operation cannot run because the used capacity of the Data Retention Utility on the secondary system exceeds the license capacity. 10-14 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 143
The pair cannot created because the model or the software version of the primary or secondary system is not supported. CBFC The pair cannot be created because the consistency group ID is not within the supported range. 10-15 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Pair cannot be created because DKC type does not support TC Asynchronous. B90A B992 Consistency group information cannot be retrieved because TC or UR is not installed. 10-16 Troubleshooting Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
NAS_Platform_System_RSG. Service Information Messages (SIMs) The VSP G200, G400, G600, G800 and VSP F400, F600, F800 storage systems generate a service information message (SIM) to notify users of a possible service requirement for the storage system. SIMs can be generated by the system's channel and storage path microprocessors or the service processor (SVP).
Device Manager - Storage Navigator. The Hitachi Data Systems customer support staff is available 24 hours a day, seven days a week. If you need technical support, log on to Hitachi Data Systems Support Connect for contact information: https:// support.hds.com/en_us/contact-us.html.
□ Configuration commands and options □ Consistency group commands and options □ Pair operation commands and options □ Monitoring commands and options □ Maintenance commands and options TC CLI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Delete pairs in CTG pairsplit Volumes to be split at the same time need to be included in the same consistency group in advance. TC CLI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 152
□ Force Delete Pairs (TC Pairs) window □ Edit Pair Options wizard □ View Pair Properties window □ View Pair Synchronization Rate window □ History window TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 153
Therefore, the number of tables does not change if you perform either of the following operations: • ShadowImage pair operation for DP-VOL over 4 TB TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 154
- A blank indicates no values are specified. • SSID: Volume's virtual SSID. A blank indicates that no virtual SSID is specified. Export Opens the window for exporting the table information. TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 155
Summary section on page B-6 • TC Pairs tab on page B-6 • UR Pairs tab on page B-8 • Mirrors tab on page B-11 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 156
Note: Encryption of data is not ensured in an LDEV with the Mixed encryption status. To manage data encryption, use an LDEV for which Encryption is Enabled or Disabled. TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 157
Sync: It is a TC pair which is not assigned to consistency group. • Sync (Specified CTG): It is a TC pair created by specifying consistency group. TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 158
This item does not appear in the table by default. To display this item, click Column Settings. Displays when you select More Actions. UR Pairs tab UR only. TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 159
Mixed: The journal contains both encrypted and ¢ unencrypted volumes. Note: Encryption of data is not ensured in an LDEV with the Mixed encryption status. To TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 160
Create UR Pairs Opens the Create UR Pairs window. Split Pairs Opens the Split Pairs window. Resync Pairs Opens the Resync Pairs window. B-10 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 161
Model / Serial Number: Remote system model and serial number. • Journal ID: Remote system journal identifier Path Group ID Path group identifier. B-11 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 162
Opens the Edit Mirror Options window. Edit Mirror Options View Remote Connection Opens the View Remote Connection Properties window when the value for Attribute is "Master". Properties B-12 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 164
Information about volumes in the Remote Storage System. • Model / Serial Number: Remote system's model and serial number. • LDEV ID: LDEV identifier. B-14 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 165
This item does not appear in the window by default. To display this item, change the Column Settings. Displays when you select More Actions. B-15 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
7-11. In this topic you can review the following tables: • Connections (To) tab on page B-17 B-16 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 167
Path Group ID Path group identifier. Status Remote connection status. • Normal: All remote paths are normal. • Failed: All remote paths are abnormal. B-17 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 168
Remote Storage System Remote Storage System's model and serial number. Path Group ID Path group identifier. Export Opens the window for exporting the table information. B-18 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 169
¢ A blank indicates that the volume is in a status other than the above. • CLPR: Volume's CLPR. • Capacity: Volume's capacity. B-19 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
When you select Fibre for Select Type the following screen is displayed. When you select iSCSI for Select Type the following screen is displayed. B-20 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 171
In that case, such a model is enclosed in parentheses when displayed on the Remote Connections window. B-21 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 172
Item Description RIO MIH Time Time limit between 10 and 100 seconds for the data- transfer operation to complete (15 is the default). B-22 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Minimum Number of Paths Specified minimum number of remote paths. RIO MIH Time (sec.) Specified RIO MIH time. Roundtrip Time (msec.) Specified roundtrip time. B-23 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
TCP Port Number: Displays the TCP port number when Port Type is iSCSI. View Remote Connection Properties window Use this window to view information about remote connections and paths. B-24 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 175
Fibre: All remote path port types within remote connection are Fibre. • iSCSI: All remote path port types within remote connection are iSCSI. B-25 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Remove Remote Connections window Use this window to remove remote connections. For complete information and instructions, see Deleting TrueCopy remote connections on page 7-18. B-26 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
For complete information and instructions, see Changing minimum paths, round trip time, other remote connection options on page 7-15. B-27 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Time limit between 1 and 500 milliseconds for data copy from P-VOL to S-VOL (1 is the default). Edit Remote Connection Options confirmation window B-28 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
For complete information and instructions, see Configuring additional remote paths on page 7-14. When you select Fibre for Select Type the following screen is displayed. B-29 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 180
When you select iSCSI for Select Type the following screen is displayed. In this topic, you can view the following tables. B-30 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 181
Displays the TCP port number of the remote storage system. Only displays when selecting iSCSI for Select Type. Add Paths Clicking adds more paths, up to eight. B-31 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Number of Remote Paths Number of remote paths including those being added. Minimum Number of Paths Specified minimum number of remote paths. B-32 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
For complete information and instructions, see Deleting remote paths on page 7-17. When you select Fibre for Select Type the following screen is displayed. B-33 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 184
When you select iSCSI for Select Type the following screen is displayed. In this topic, you can view the following tables. B-34 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 185
Displays the TCP port number of the remote storage system. Only displays when selecting iSCSI for Select Type. Remove Check box for deleting the path from the remote connection. B-35 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Specified minimum number of remote paths. Selected Remote Paths table Item Description Local Information about the local storage system port. • Port ID: Displays the port identifier. B-36 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use this window to change options that affect the replication system. For complete information and instructions, see Changing remote replica options on page 5-4. B-37 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 188
Storage System Options on page B-39 • CU Options on page B-39 Setting Fields Item Description Copy Type Type of pair: • TC: TrueCopy • UR: Universal Replicator B-38 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 189
Change CU Options Opens the Change CU Options window. If you select Disable in Maximum Initial Copy Activities, you cannot select this button. B-39 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
(1 to 16). This can be specified only when you select Enable for Maximum Initial Copy Activities in CU Options of the Edit Remote Replica Options window. B-40 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
CU Options on page B-42 Storage System Options Item Description Maximum Initial Copy Number of volumes that can be copied per initial copy Activities operation. B-41 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use this window to create pairs. For complete information and instructions, see Creating pairs on page 6-3. In this topic, you can view the following tables. B-42 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 193
Target Alias: Selections for iSCSI target alias. All the LUNs in the indicated port for Available LDEVs if Any is selected. Displays when iSCSI port is selected for Port Name. B-43 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 194
Displayed only for UR pairs. • Port ID: Port identifier. • Host Group Name / iSCSI Target Alias: Host group name or iSCSI target alias. B-44 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 195
Model / Serial Number: Model and serial number. ¢ LDEV ID: LDEV identifier. ¢ Port ID: Port identifier of the volume. ¢ B-45 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 196
CTG ID Displays consistency groups registered in the storage system. An asterisk indicates it is assigned to a pair in the Select Pairs table. B-46 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 197
• Host Group Name / iSCSI Target Alias: Host group name or iSCSI target alias. • iSCSI Target Name: Volume's iSCSI target name. B-47 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 198
• T10 PI: Volume's T10 PI attribute information. Enabled: Volume's T10 PI attribute is enabled. ¢ B-48 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Deletes the specified pair from the table. Change Settings window Use this window in the pair creation wizard to change options that affect how the pair is created. B-49 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 200
256; default is 32. For GAD pairs, this is not displayed. Error Level UR only Whether to split all pairs in the mirror if a failure occurs during this operation: B-50 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Local Storage System Information about volumes in the accessed system. • LDEV ID: LDEV identifier. • LDEV Name: LDEV name. • Port ID: Port identifier. B-51 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 202
T10 PI: Volume's T10 PI attribute information. Enabled: Volume's T10 PI attribute is enabled. ¢ Disabled: Volume's T10 PI attribute is disabled. ¢ B-52 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use this wizard to split pairs. Split Pairs window Use this window to split pairs. For complete information and instructions, see Splitting pairs on page 6-6. B-53 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 204
Pair Position: Whether volume is a P-VOL or S-VOL. • Attribute: LDEV attribute. • Capacity: Volume's capacity. • CLPR: Volume's CLPR. Copy Type Type of pair: • TC: TrueCopy B-54 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 205
VOL depends on the Primary Volume Fence Level Setting. Default. • Disable: Prevents writing to the P-VOL. Available only when performing the split operation from the pair's primary storage system. B-55 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Pair status. Secondary Volume Write Whether the S-VOL can be written to while the pair is split. • Enabled: Can write to S-VOL. B-56 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use this wizard to resynchronize pairs. Resync Pairs window Use this window to resynchronize pairs. For complete information and instructions, see Resynchronizing pairs on page 6-8. B-57 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 208
Capacity: Volume's capacity. • CLPR: Volume's CLPR. Copy Type Type of pair: • TC: TrueCopy Status Pair status. Copy Priority Order that pairs are resynchronized. B-58 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 209
If you enter a number from 5 to 15, the speed of 4 (fast copy pace) is used. B-59 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Data: Cannot be written to. • Status: Can be written to only if the local system can change S-VOL status to PSUE; otherwise no. B-60 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use this wizard to delete pairs. Delete Pairs window Use this window to delete pairs. For complete information and instructions, see Deleting pairs on page 6-10. B-61 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 212
• Attribute: LDEV attribute. • Capacity: Volume's capacity. • CLPR: Volume's CLPR. Copy Type Type of pair: • TC: TrueCopy Status Pair status. B-62 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 213
P-VOL and S-VOL to unpaired volumes. Default. • Force: Deletes the pair even when the local system cannot communicate with the remote system. B-63 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Delete Mode How the pair is deleted. Remote Storage System Information about the remote system. • Model / Serial Number: Model and serial number. B-64 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
For complete information and instructions, see Forcibly deleting pairs on page 7-10. Selected LDEVs table Item Description LDEV ID LDEV identifier. LDEV Name LDEV name. B-65 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
S-VOL status to PSUE; otherwise no. • Never: The P-VOL can be written to. The value set for the selected pair is the default. B-66 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Path Group ID Path group identifier. View Pair Properties window Use this window to view the data related to pairs and their volumes. B-67 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 218
• Attribute, capacity: Local system's volume attribute and capacity. If the volume does not have an attribute, only the capacity is displayed. B-68 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 219
Received or Enabled/Not Received is displayed. Indicates whether a write operation is received from the host or not. Copy Pace Speed that data is copied. B-69 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Use this window to view the percentage of synchronized data between P-VOL and S-VOL. For complete information and instructions, see Monitoring TC pair synchronization rate on page 7-7. B-70 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 221
Model / Serial Number: Remote system's model and serial number. • LDEV ID: LDEV identifier. • Virtual Storage Machine: Virtual storage machine's model type and serial number. B-71 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Date and time of the operation. Local Storage System Information about volumes in the accessed system. • LDEV ID: LDEV identifier. • Provisioning Type: Volume's provisioning type. B-72 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 223
• LDEV ID: LDEV identifier. • Pair Position: Whether the volume is a primary or secondary volume. • Provisioning Type: Volume's provisioning type. B-73 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 224
Description is other than Pair Add Complete or Pair Resync. Complete, a hyphen (-) is displayed. Export Opens the window for exporting table information. B-74 TC GUI reference Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
In a 3DC configuration, data is copied from a local site to an intermediate site and then to a remote site (3DC cascade configuration), or from a local site to two remote sites (3DC multi-target configuration). acknowledgement Glossary-1 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
RAID group. business continuity blade A computer module, generally a single circuit board, used mostly in servers. BLK, blk block Glossary-2 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
A volume that is being used by more than one replication function. For example, a volume that is the primary volume of a TrueCopy pair and the primary volume of a ShadowImage pair is a shared volume. Command Control Interface Glossary-3 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Shows a time stamp to indicate how close the target volume is to the source volume. C/T also shows the time stamp of a journal and extended consistency group. control memory Another name for shared memory. Glossary-4 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 229
The primary and secondary volumes each have their own cylinder bitmap. When the pair is resynchronized, the cylinder bitmaps are merged, and the differential data is copied to the secondary volume. DASD direct-access storage device Glossary-5 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
A set of procedures to recover critical application data and processing after a disaster or other failure. disk array Disk array, or just array, is another name for a RAID storage system. Glossary-6 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 231
A set of device emulation types that can be intermixed within a RAID group and treated as a group. env. environment Glossary-7 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
FICON Fibre Connectivity free capacity The amount of storage space (in bytes) that is available for use by the host system(s). fibre switch Glossary-8 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
A group of hosts of the same operating system platform. host mode Operational modes that provide enhanced compatibility with supported host platforms. Used with fibre-channel ports on RAID storage systems. Glossary-9 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 234
See also external volume. IO, I/O input/output I/O mode I/O actions on the P-VOL and S-VOL of the global-active device pair. IOPS I/Os per second journal Glossary-10 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
L2 secondary volumes. See also cascade configuration. logical block address local control port; link control processor logical control unit LDEV logical device LDKC See logical disk controller (LDKC). Glossary-11 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 236
(LU) path The path between an open-systems host and a logical unit. logical volume See volume. logical unit logical unit number LUNM Hitachi LUN Manager Glossary-12 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 237
MB/sec, MBps megabytes per second migration volume A volume used to migrate data from a different storage system, such as Hitachi Unified Storage VM. missing interrupt handler mirror In Universal Replicator, each pair relationship in and between journals is called a "mirror".
Page 238
Indicates the condition of a copy pair. A pair must have a specific status for specific operations. When an operation completes, the status of the pair changes to the new status. parity group See RAID group. Glossary-14 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The primary site can also be called the "local site". Glossary-15 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Used to determine the volume in the global-active device pair on which server I/O should continue when a failure occurs in a path or a storage system. Quorum disk is installed in an external storage system. Glossary-16 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
TrueCopy and Universal Replicator provide remote replication. See also in-system replication. remote site See secondary site. remote storage system The system containing the copy in the remote location of a remote replication pair. Glossary-17 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 242
The remote site can also be called the "secondary site". See also primary site. secondary storage system The remote storage system Glossary-18 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
The volume in a copy pair that is the copy. The following Hitachi products use the term "secondary volume": Device Manager - Storage Navigator, Thin Image, ShadowImage, TrueCopy, and Universal Replicator. See also primary volume. service information message (SIM) SIMs are generated by a RAID storage system when it detects an error or service requirement.
Page 244
Additional operational parameters for the RAID storage systems that enable the storage system to be tailored to unique customer operating requirements. SOMs are set on the service processor. terabyte Glossary-20 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 245
RAID level and device emulation type. LUN volume A custom-size volume whose size is defined by the user using Virtual LVI/Virtual LUN. Also called a custom volume (CV). Glossary-21 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 246
(V-VOL) A logical volume that has no physical storage space. Hitachi Thin Image uses V-VOLs as secondary volumes of copy pairs. In Dynamic Provisioning, Dynamic Tiering, and active flash, V-VOLs are referred to as DP-VOLs. Hitachi Virtual LVI/LUN...
GAD pairs B-13 description Global storage virtualization 4-13 planning 3-25 supported configurations 3-29 Data Retention Utility, sharing volumes with delete mode, setting 6-11 Index-1 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 248
7-11 pairs scheduling order for initial copies creating secondary volume write, setting deleting 6-10 setting up TrueCopy duplicate volumes and hosts 3-10 ShadowImage, sharing volumes Index-2 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 249
Virtual LUN 4-12 Volume Migration 4-12 volumes, sharing with others Index-3 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 250
Index-4 Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 251
Hitachi TrueCopy® User Guide for Hitachi Virtual Storage Platform Gx00 and Fx00 Models...
Page 252
Hitachi Data Systems Corporate Headquarters 2845 Lafayette Street Santa Clara, California 95050-2639 U.S.A. www.hds.com Regional Contact Information Americas +1 408 970 1000 info@hds.com Europe, Middle East, and Africa +44 (0)1753 618000 info.emea@hds.com Asia Pacific +852 3189 7900 hds.marketing.apac@hds.com MK-94HM8019-04...