Grundfos CONTROL MPC Installation And Operating Instructions Manual page 13

11.2 Overview
Section Display and display number
11.4 Status (1)
11.4.1 Current alarms (3.1)
11.4.2 System (1.2)
11.4.3 Operating mode (1.2.1)
11.4.4 Setpoint (1.2.2)
11.4.5 Setpoint influence (1.2.3)
11.4.6 Measured values (1.2.4)
11.4.7
Analog inputs (1.2.5)
11.4.8 Pump 1...6 (1.3 to 1.8)
11.5 Operation (2)
11.5.1 Operation (2)
11.5.2 System operating mode (2.1.1)
11.5.3 Control mode (2.1.2)
11.5.4 Setpoints (2.1.3)
11.5.5 Individual pump control (2.1.4)
11.5.6 Setting of individual operating mode (2.1.4.1 to 2.1.4.6)
11.6 Alarm (3)
11.6.1 Alarm status (3)
11.6.2 Current alarms (3.1)
11.6.3 Alarm log (3.2)
11.7 Settings (4)
11.7.1 Primary controller (4.1)
11.7.2 PI controller (4.1.1)
11.7.3 Alternative setpoints (4.1.2)
11.7.4 Alternative setpoints 2 to 7 (4.1.2.1 to 4.1.2.7)
11.7.5 External setpoint influence (4.1.3)
11.7.6
Setting of influence function (4.1.3.2)
11.7.7 Primary sensor (4.1.4)
11.7.8 Clock program (4.1.6)
11.7.9
Proportional pressure (4.1.7)
11.7.10 S-system configuration (4.1.8)
11.7.11
Pump cascade control (4.2)
11.7.12 Min. time between start/stop (4.2.1)
11.7.13 Max. number of starts/hour (4.2.1)
11.7.14 Standby pumps (4.2.3)
11.7.15 Forced pump changeover (4.2.4)
11.7.16 Pump test run (4.2.5)
11.7.17
Pilot pump (4.2.6)
11.7.18
Pump stop attempt (4.2.7)
11.7.19
Pump start and stop speed (4.2.8)
11.7.20
Min. performance (4.2.9)
11.7.21
Compensation for pump start-up time (4.2.10)
11.7.22
Secondary functions (4.3)
11.7.23 Stop function (4.3.1)
11.7.24
Soft pressure build-up (4.3.3)
11.7.25
Emergency run (4.3.5)
11.7.26 Digital inputs (4.3.7)
11.7.27 Functions of digital inputs (4.3.7.1)
11.7.28 Analog inputs (4.3.8)
11.7.29 Analog inputs (4.3.8.1 to 4.3.8.7)
11.7.30 Analog inputs and measured value (4.3.8.1.1 to 4.3.8.7.1)
11.7.31 Digital outputs (4.3.9)
11.7.32 Functions of digital outputs (4.3.9.1 to 4.3.9.16)
11.7.33 Min., max. and user-defined duty (4.3.14)
11.7.34 Min. duty (4.3.14.1)
11.7.35 Max. duty (4.3.14.2)
11.7.36 User-defined duty (4.3.14.3)
11.7.37
Pump curve data (4.3.19)
11.7.38 Control source (4.3.20)
11.7.39 Fixed inlet pressure (4.3.22)
11.7.40 Flow estimation (4.3.23)
See page
15
15
15
16
16
16
17
17
17
18
18
18
19
21
21
22
23
23
24
24
25
25
26
27
27
28
29
29
30
31
31
32
32
32
33
33
34
34
35
35
36
36
37
37
39
40
40
41
41
42
42
43
43
44
44
45
45
46
47
47
48
13