Dodge 2001 Ram 1500 Owner's Manual page 2796

BR/BE
EMISSIONS CONTROL (Continued)
(M) Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
Generic Scan
Tool P-Code
P0713 Trans Temp Sensor Voltage Too
P0713 (M) Trans Temp Sensor Voltage Too
P0720 (M) Low Output SPD Sensor RPM,
P0720 (M) Low Output Spd Sensor RPM Above
P0740 (M) Torq Con Clu, No RPM Drop at
P0743 (M) Torque Converter Clutch Solenoid/
P0743 (M) Torque Converter Clutch Solenoid/
P0748 (M) Governor Pressur Sol Control/Trans
P0748 (M) Governor Pressure Sol Control/Trans
P0751 (M) O/D Switch Pressed (Lo) More Than
P0751 (M) O/D Switch Pressed (LO) More Than
P0753 (M) Trans 3-4 Shift Sol/Trans Relay
P0753 (M) Trans 3-4 Shift Sol/Trans Relay
P0756 AW4 Shift Sol B (2-3) Functional
P0783 (M) 3-4 Shift Sol, No RPM Drop at
P0801 Reverse Gear Lockout Circuit Open
P0830 Clutch Depressed Switch Circuit
P0833 Clutch Released Switch Circuit
P1110 Decrease Engine Performance Due
To High Intake Air Temperature
P1180 Decreased Engine Performance Due
To High Injection Pump Fuel Temp
(G) Generator lamp illuminated
DRB Scan Tool Display
High
High
Above 15 MPH
15 mph
Lockup
Trans Relay Circuits
Trans Relay Circuits
Relay Circuits
Relay Circuits
5 Minutes
5 Min
Circuits
Circuits
Failure
Lockup
or Short
Brief Description of DTC
Transmission fluid temperature sensor input above
acceptable voltage. Was MIL code 37.
Voltage greater than 3.76 volts (4-speed auto. trans.
The relationship between the Output Shaft Speed Sensor
and vehicle speed is not within acceptable limits.
Output shaft speed is less than 60 rpm with vehicle speed
above 15 mph (4-speed auto. trans. only).
Relationship between engine and vehicle speeds
indicated failure of torque convertor clutch lock-up system
(TCC/PTU solenoid)
An open or shorted condition detected in the torque
converter clutch (part throttle unlock) solenoid control
circuit. Shift solenoid C electrical fault - Aisin transmission
An open or shorted condition detected in the torque
converter part throttle unlock solenoid control circuit (3 or
4-speed auto. trans. only).
An open or shorted condition detected in the Governor
Pressure Solenoid circuit or Trans Relay Circuit in JTEC
RE transmissions.
An open or shorted condition detected in the governor
pressure solenoid or relay circuits (4-speed auto. trans.
Overdrive override switch input is in a prolonged
depressed state.
Overdrive Off switch input too low for more than 5
minutes (4-speed auto. trans. only).
An open or shorted condition detected in the overdrive
solenoid control circuit or Trans Relay Circuit in JTEC RE
transmissions. Was MIL code 45.
An open or shorted condition detected in the transmission
2-4 shift solenoid circuit (4-speed auto. trans. only).
Shift solenoid B (2-3) functional fault - Aisin transmission
The overdrive solenoid is unable to engage the gear
change from 3rd gear to the overdrive gear.
An open or shorted condition detected in the transmission
reverse gear lock-out solenoid control circuit.
Problem detected in clutch switch circuit.
Problem detected in clutch switch circuit.
Intake manifold air temperature is above the engine
protection limit. Engine power will be derated.
Fuel temperature is above the engine protection limit.
Engine power will be derated.
EMISSIONS CONTROL
only).
only).
25 - 9