Summary of Contents for Dodge 2008 DX-49 Magnum SRT8
Page 1
Magnum SRT8 2 0 0 8 O W N E R ’ S M A N U A L...
Page 2
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel. The VIN is visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information VIN Location Disclosure Label affixed to a window on your vehicle, the NOTE: It is illegal to remove the VIN.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Wireless Ignition Node (WIN) ... . .12 FOB With Integrated Key .
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm ....22 Programming Additional Transmitters ..23 Transmitter Battery Service .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided integrated key into the igni- tion switch with either side up.
Fob with Integrated Key The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key, which stores in the rear of the Fob. The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tip Start Feature Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running.
Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key. NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key Immobilizer System is not compat- ible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil SpeedPass™, additional fobs, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the fob being used to...
procedure. This procedure consists of programming a blank fob to the vehicle electronics. A blank fob is one that has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle fobs with you to the authorized dealer. Customer Sentry Key (Fob) Programming If you have two valid Sentry Keys , you can program new Sentry Keys...
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed.
To Arm the System Remove the key from the ignition switch and either press a power door LOCK switch while the driver or passenger door is open, or press the LOCK button on the Remote Keyless Entry (RKE) transmitter. After the last door is closed, or if all doors are closed, the system will arm itself in about 16 seconds.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the alarm system is armed and the battery becomes disconnected the system will remain armed when the battery is reconnected. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle.
Remote Keyless Entry (RKE) Transmitter To unlock the doors: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Turn Headlights On with Remote Key Unlock This feature activates the headlights for up to 90 seconds when the doors are unlocked with the transmitter. The time for this feature is programmable. Refer to “Turn Headlights On with Remote Key Unlock,”...
• You may need to be less than 35 ft (11 m) from the vehicle when using the transmitter to turn off the Panic Alarm due to the radio frequency noises emitted by the system. Programming Additional Transmitters Refer to Sentry Key , “Customer Sentry Key (Fob) Programming.”...
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place.
How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Liftgate closed • HAZARD switch off • BRAKE switch inactive (brake pedal not pressed) •...
Page 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit REMOTE START Mode without Driving the Vehicle Allow the engine to run for the entire 15 minute cycle. To Exit REMOTE START Mode and Drive the Vehicle Before the end of the 15 minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
DOOR LOCKS Manual Door Locks To lock each door, push the door LOCK plunger on each door trim panel downward. To unlock each door, pull the door LOCK plunger on each door trim panel upward. Door LOCK Plunger THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If the door LOCK plunger is down when you shut the door, the door will lock.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door LOCK switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door LOCK Switch If you press the power door LOCK switch while the key is in the ignition, and any front door is open, the power locks will not operate.
Page 31
6. The doors were not previously locked using the power door LOCK switch or Remote Keyless Entry (RKE) transmitter. Automatic Door Locks Programming The Automatic Door Locks feature can be enabled or disabled. Refer to “Lock Doors Automatically at 15 mph (24 km/h),”...
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child Protection Door Lock system. To Engage the Child Protection Door Lock System 1.
Page 33
WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: • After engaging the Child Protection Door Lock sys- tem, always test the door from the inside to make certain it is in the desired position.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Repeat Steps 1 and 2 for the opposite rear door. NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. WINDOWS Power Windows The window controls on the driver’s door control all the...
Page 35
WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power WINDOW switches. Such entrapment may result in serious injury or death. AUTO-Down Feature The driver door power WINDOW switch and some model passenger door power WINDOW switches have an AUTO-down feature.
Page 36
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To close the window part way, lift the WINDOW switch to the first detent and release it when you want the window to stop. The power WINDOW switches will remain active for up to 60 minutes after the ignition switch is turned off.
Window LOCKOUT Switch Reset Anytime the vehicle battery is disconnected or goes dead, the AUTO-up function will be disabled. To reactivate the auto-up feature, perform the following steps after vehicle power is restored: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 1.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE The liftgate can be unlocked or locked by the Remote Keyless Entry (RKE) transmitter or by activating the power door lock switches located on the front doors. Once unlocked, the liftgate can be opened or closed. To open the liftgate, depress the liftgate release switch located in the exterior handle and pull the liftgate open with one fluid motion.
Page 39
NOTE: If a power malfunction occurs, you can use the emergency liftgate latch release to open the liftgate. The emergency liftgate latch release is located behind a snap-in cover on the liftgate trim panel. Emergency Liftgate Latch Release Location THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! •...
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, the front airbags for both the driver and front passenger, the optional supplemental side curtain airbags for the driver and passengers seated next to a window, and the optional supplemental front seat mounted side airbags.
Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
Page 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. •...
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 45
6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 46
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seatback is in the fully upright and locked position when occupied. If the rear seatback is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, the vehicle should immediately be taken to your dealer for service.
As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up and down to make sure that it is locked in position.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the Occupant Re- straint Controller (ORC). (Refer to information on Air- bags in this section). Like the front airbags, the preten- sioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling the seat belt and turn off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 51
mounted in the instrument panel, above the glove com- partment. The words SRS AIRBAG are embossed on the airbag covers. Front Airbag Components 1 — Airbags 2 — Knee Bolsters THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment.
Page 52
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 53
If the vehicle is equipped with supplemental front seat mounted side airbags, they are marked with an SRS label sewn into the outboard side of the seat. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! • If your vehicle is equipped with supplemental front seat mounted side airbags, do not use accessory seat covers or place objects between you and the seat airbags;...
Page 54
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the curtain airbags. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger.
Page 55
3. Older children who do not use child restraints or belt-positioning booster seats should ride properly buck- led up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. 4. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible and use the proper child restraint.
Page 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 57
• Seat Belt Reminder Light • Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners How the Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
Page 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG Warning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 59
vehicle. A quantity of nontoxic gas is generated to inflate the side curtain airbag. The inflating side cur- tain airbag pushes the outside edge of the headliner out of the way and covers the window. The airbag inflates in about 30 ms (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side...
Page 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not replace the seat cover with an aftermarket seat cover. • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar . • At no time should any supplemental restraint sys- tem (SRS) component or SRS-related component or fastener be modified or replaced with any part except...
Page 61
NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision that deploys the airbags, any or all of the following may occur: •...
Page 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System In the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following func- tions: •...
NOTE: Perchlorate Material — special handling may ap- ply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Airbag Warning Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system promptly: •...
Page 64
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance.
Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • Airbag disable light status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) •...
Page 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 67
“LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
Page 69
Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it.
Page 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle.
Page 71
Installing the LATCH-Compatible Child Restraint System We urge you to follow the manufacturer’s directions carefully when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that are provided with the child restraint system. The rear seat lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback and are just visible when...
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
Page 73
keep the belt tight; however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. Seat belts with an automatic locking retractor have a distinctive label on the seat belt webbing. The seat belt must be in the Automatic Locking mode in order to enable a child restraint to be tightly installed.
Page 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach a child restraint tether strap: 1. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. Tether Strap Mounting 2. Attach the tether strap hook of the child restraint to the tether anchor and remove slack in the tether strap according to the child restraint manufacturer’s instruc- tions.
Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 77
Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
Page 79
Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks.
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjusting Rearview Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight...
Exterior Mirrors Folding Feature — If Equipped Some models have exterior mirrors that are hinged. The hinge allows the mirror to pivot forward and rearward to resist damage. The hinge has three detent positions, full forward, full rearward, and normal. Driver’s-Side Outside Mirror Auto Dimmer —...
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Electric Rear Window Defroster. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 NOTE: For UConnect following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 UConnect allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone...
Page 90
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE different electronic devices to connect to each other without wires or a docking station, so UConnect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect system.
The radio display will be used for visual prompts from the UConnect system such as CELL or caller ID on certain radios. Operation Voice commands can be used to operate the UConnect system and to navigate through the UConnect menu structure.
Page 92
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the UConnect system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnect system sessions begin with a press of the PHONE button on the radio control head. Cancel Command At any prompt, after the beep, you can say Cancel and you will be returned to the main menu.
Page 93
• You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority. You can pair up to seven cellular phones to your UConnect system. However, at any given time, only one cellular phone can be in use, connected to your UConnect system.
Page 94
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the name of the person you want to call. • After the Ready prompt and the following beep, say the name of the person you want to call. For example, you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect phonebook.
Page 95
The UConnect system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Phonebook Download UConnect allows the user to download entries from their phone via Bluetooth .
Page 96
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. •...
Page 97
• After you enter the name, the UConnect system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the UConnect system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect your cellular service provider for the features that you have.
Page 99
to Toggling Between Calls in this section. To combine two calls, refer to Conference Call in this section. Place/Retrieve a Call From Hold To put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the PHONE button until you hear a single beep.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Redial • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Redial. • The UConnect system will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the UConnect system.
Page 101
• After the Ready prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
Page 102
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnect system to allow use of this vehicle feature in emergency situations, when the cell phone has network coverage and stays paired to the UConnect system. Towing Assistance If you need towing assistance: •...
Page 103
When calling a number with your UConnect system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the “Voice Recognition” button and say the sequence you wish to enter, followed by the word Send. For example, if required to enter your PIN number followed with a pound, (3 7 4 6 #), you can press the “Voice Recognition”...
Page 104
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect sys- tem will not repeat a phone number before you dial it). • Press the PHONE button to begin. •...
Mute/Un-Mute (Mute Off) When you mute the UConnect system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect system: •...
Page 106
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say List Phones. • The UConnect system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recogni- tion”...
Things You Should Know About Your UConnect System UConnect Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “UConnect Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the UConnect system Voice Training feature may be used.
Page 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period. •...
Page 109
• In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, •...
Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109...
Page 112
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 113
Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 114
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. Pressing the VR hard-key while the system is speaking is known as “barging in.”...
Page 117
Changing the Volume 1. Start a dialogue by pressing the VR hard-key. 2. Say a command (e.g., HELP). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition system is speaking. Please note the volume setting for VR is different then the audio system.
Page 118
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • RADIO MENU (to switch to the radio menu) • MAIN MENU (to switch to the main menu) Satellite Radio To switch to satellite radio mode say SAT or SATELLITE RADIO. In this mode, you may say the following com- mands: •...
− CONTINUE (to continue recording) − DELETE (to delete the recording) • PLAY MEMOS (to play previously recorded memos) — During the playback you may press the VR hard- key to stop playing memos. You continue by saying one of the following commands: −...
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats The power SEAT switch is on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward, or to tilt the seat. The passenger’s seat will move up or down, forward or rearward.
WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraint so that the upper edge is as high as practical. To raise it, pull upward on the head restraint.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats Heated seats provide comfort and warmth on cold days and can help soothe sore muscles and backs. The heaters provide the same heat level for both cushion and back. The driver seat and front passenger seat are heated. The controls for each heater are located near the bottom center of the instrument panel.
LEDs changes from two to one, indicating the change. Operation on the low setting also turns off automatically after 30 minutes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion, or other physical conditions must exercise care...
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. WARNING! • Be certain that the seatback is securely locked into position.
Page 127
Next, move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. Hood Safety Catch Use the hood prop rod (if equipped) to secure the hood in the open position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch The HEADLIGHT switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights, and fog lights.
Automatic Headlights — If Equipped This system automatically turns the headlights ON or OFF according to ambient light levels. To turn the system ON, rotate the HEADLIGHT switch counterclockwise to the AUTO (A) position. When the system is on, the headlight time delay feature is also on.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights On with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned ON if the HEADLIGHT switch is placed in the AUTO posi- tion.
Daytime Running Lights — If Equipped The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is ON, the headlights are off, and the parking brake is off. The HEADLIGHT switch must be used for normal nighttime driving.
Page 132
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever Turn Signals Move the multifunction lever up or down and the corresponding turn signal indicator in the instrument cluster flashes to show proper operation of the front and rear turn signal lights. You can also signal a lane change by moving the lever partially up or down without moving beyond the detent.
Flash to Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE because a door is open. This includes the glove box light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control The dimmer control is part of the HEADLIGHT switch and is located on the left side of the instrument panel.
Windshield Wiper/Washer Control Rotate the end of the multifunction lever to the first detent past the intermittent settings for low speed wiper operation, or to the second detent past the intermittent settings for high speed wiper operation. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 CAUTION! Turn the windshield wipers off when driving through an automatic car wash.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
if the HEADLIGHT switch is placed in the AUTO posi- tion. In addition, the headlights will turn off when the wipers are turned OFF if they were turned ON by this feature. The Headlights On With Wipers feature can be enabled or disabled.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle. ADJUSTABLE PEDALS —...
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the transmission is in REVERSE or when the speed control is ON.
1 — CANCEL 2 — RESUME ACCEL 3 — ON/OFF 4 — SET DECEL UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 To Activate Push and release the ON/OFF button located on the end of the speed control lever. The indicator light in the instrument cluster will illuminate to show that the speed control sys- tem is ON.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle reaches the speed desired, push the lever downward to SET DECEL and release. Remove your foot from the accelerator pedal and the vehicle will operate at the selected speed.
Tapping the lever to RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped speed increases, so tapping the lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while speed control is set, push downward and hold the lever in SET DECEL.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink ), storage for sunglasses, and an optional power SUNROOF switch. Overhead Console Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights.
GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink unit operates off your vehicle’s battery. The HomeLink buttons are located in the overhead console, and contain one, two, or three dots/lines desig- nating the different HomeLink channels.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 147
to HomeLink for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink buttons while keeping the EVIC display in view.
Page 148
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: After training a HomeLink garage door does not operate with HomeLink and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5.
NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Continue to press and hold the HomeLink button while you press and release - every two seconds (“cycle”) your hand-held transmitter until HomeLink has successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAIN- ING”...
The HomeLink Universal Transceiver is disabled when the Vehicle Security Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLink , here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the learn button on the garage door opener to complete the training for rolling code.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power SUNROOF switch is located between the sun visors on the overhead console. Power Sunroof Controls WARNING! • Never leave children in a vehicle with the key in the ignition switch.
Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully and then stop automatically. This is called Express Open. During Express Open operation, any movement of the SUNROOF switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
ELECTRICAL POWER OUTLETS There are three 12-volt electrical outlets on this vehicle. All of the outlets are protected by fuses. The 12-volt power outlet next to the ash receiver tray (if equipped with an optional Smoker’s Package) has power available only when the ignition is ON. This outlet will also operate a conventional cigar lighter unit.
Page 156
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. Center Console Power Outlet The auxiliary outlet is also powered directly from the battery (power available at all times).
Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupants’...
STORAGE Console Features The center console contains two shift bezel cubby bins with rubber mats for holding small items. For vehicles not equipped with navigation radio, the console also contains an extra storage bin located below the climate control, which holds up to four CD jewel cases. Without Vehicle Entertainment System (VES) Two separate storage compartments are also located underneath the armrest.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12-volt power outlet and a molded-in coin holder (designed to hold various size coins).
Page 161
The lower load floor is hinged to provide access to the spare tire (if equipped), battery, and rear electrical power distribution center. The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they provide a continuous, nearly-flat extension of the removable tri-fold load floor.
Page 162
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Load Floor Partially Folded Load Floor Fully Folded...
Page 163
Rollaway Tonneau Cover — If Equipped The removable rollaway tonneau cover mounts in the cargo area behind the top of the rear seats. The tonneau cover, when extended, covers the cargo area to keep items out of sight. Notches in the trim panels near the liftgate opening secure the extended tonneau cover in place.
Page 164
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE (located on the ends of the tonneau cover housing) into the left or the right front attachment point shown. Front Attachment Points Then, insert the spring-loaded post on the opposite end of the tonneau cover housing into the remaining front attachment point.
Page 165
Waterproof Liner The optional waterproof liner can be placed over the lower load floor. Waterproof Liner UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Cargo Organizer The optional cargo organizer can also be placed into the lower load floor. Lift the handle and pull to open the cargo organizer.
Page 166
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks The tie-downs located on the cargo area floor and on the rear trim panels should be used to safely secure loads when the vehicle is moving. WARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap.
• Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway.
Page 168
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To adjust, remove, or install the crossbars, proceed as follows: Roof Luggage Rack 1. Flip the lever on the end of the crossbar upward. 2. Turn the lever counterclockwise to loosen the lower clamp.
Page 169
CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • Long loads, which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD LEVELING SYSTEM The automatic load leveling system will provide a level- riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mi (1.6 km) of driving for the leveling to complete depending on road surface conditions.
Page 172
170 UNDERSTANDING YOUR INSTRUMENT PANEL Two Types Of Signals ....204 Electrical Disturbances ....205 AM Reception .
Page 173
Operating Instructions — Hands-Free Communication (UConnect ) (If Equipped) . . . 226 Clock Setting Procedure ....226 Sales Code RES — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) .
Page 174
172 UNDERSTANDING YOUR INSTRUMENT PANEL Kicker 13-Speaker High Performance Sound System With Driver-Selectable Surround (DSS) – If Equipped ....250 Kicker Mobile Surround (KMS1) – If Equipped .
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Trip Odometer Button Press this button to change the display from odometer to either of two trip odometer settings.
Page 178
176 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Electronic Throttle Control (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if there is a problem with the Elec- tronic Throttle Control system.
Page 179
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (116°C) or greater, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–110°C).
Page 180
178 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Check for an inoperative outside light bulb if either indicator flashes at a rapid rate. 10. Airbag Warning Light This light will turn on for six to eight seconds as a bulb check when the ignition switch is first turned ON.
Page 181
speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. (See page 300 for more infor- mation.) 14. Oil Pressure Warning Light This light shows low engine oil pressure. The light should turn on momentarily when the engine is started.
Page 182
180 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Electronic Vehicle Information Center Display This display shows the Electronic Vehicle Information Center (EVIC) messages when the appropriate conditions exist. (See page 185 for more information.) Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap”...
Page 183
Immediate repair is necessary if brake failure is indicated. WARNING! Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident.
Page 184
182 UNDERSTANDING YOUR INSTRUMENT PANEL 22. Tire Pressure Monitoring Telltale Light — If Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
Page 185
as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replace- ment or alternate tires and wheels allow the TPMS to continue to function properly.
Page 186
184 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Anti-Lock Brake Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
The MIL flashes to alert you to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. (See page 381 for more information.) ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) Electronic Vehicle Information Center...
Page 188
186 UNDERSTANDING YOUR INSTRUMENT PANEL • Navigation system screens (if equipped), • Audio mode display, • Surround Sound modes (if equipped with Driver- Selectable Surround [DSS]), and • Performance Pages (if equipped). The system allows the driver to select information by pressing the following buttons mounted on the steering wheel.
Press the AUDIO MODE button to select the Compass/Temp/Audio screen. Along with compass reading and outside temperature, this screen will display radio and media mode AUDIO information depending on which radio is in the MODE vehicle. Refer to “Remote Sound System Con- Button trols”...
Page 190
188 UNDERSTANDING YOUR INSTRUMENT PANEL • Channel # Transmit • Channel # Training • Channel # Trained • Clearing Channels • Channels Cleared • Did Not Train • Left Front Low Pressure (with a single chime). Refer to “Starting And Operating, Tire Section” •...
• Braking Distance (if equipped with Performance Pages) • 1/8 Mile (if equipped with Performance Pages) • 1/4 Mile (if equipped with Performance Pages) • Instantaneous G-Force (if equipped with Performance Pages) • Peak G-Force (if equipped with Performance Pages) •...
Page 192
190 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level.
button once to clear the resettable function being dis- played. To reset all resettable functions, press and release the FUNCTION SELECT button a second time within three seconds of resetting the currently-displayed func- tion. (>Reset ALL will display during this three-second window.) UNDERSTANDING YOUR INSTRUMENT PANEL 191 Performance Pages —...
Page 194
192 UNDERSTANDING YOUR INSTRUMENT PANEL The Performance Pages include the following features: • 0-60 mph (0-100 km/h) • Braking Distance • 1/8 Mile • 1/4 Mile • Instantaneous G-Force • Peak G-Force • Digital Speedometer To access, press and release the MENU button until Performance Pages displays in the EVIC.
Page 195
Braking Distance When selected, this screen displays the vehicle’s braking distance and the speed at which the brake pedal was depressed. • This feature will only function when applying the brakes at speeds above 30 mph (48 km/h). • Engaging the parking brake will disable this feature. •...
Page 196
194 UNDERSTANDING YOUR INSTRUMENT PANEL • The time and speed will continue to display until the FUNCTION SELECT button is pressed. • Pressing the FUNCTION SELECT button will clear the current run and display the vehicle’s best 1/8 mile (1/4 mile) run. •...
Compass Display The compass readings indicate the direction the vehicle is facing. Press and release the COMPASS button to display one of eight com- pass readings and the outside temperature. COM- PASS Button Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually.
Page 198
196 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between magnetic North and geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
1. Turn the ignition switch ON. 2. Press and hold the COMPASS button for approxi- mately two seconds. 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map.
Page 200
198 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC displays this symbol to indicate an incoming call. Incom- ing Call The EVIC displays this symbol to indicate that the UConnect phone is currently in analog mode. Analog The EVIC displays this symbol to indicate that the UConnect phone is currently roaming.
The EVIC displays this symbol to indicate that a phone connection has been made. Call in Progress The EVIC displays this symbol to indicate that the UConnect phone is currently not avail- able. Phone Avail- able Navigation — If Equipped Navigation Display Control Press and release the MENU button until Navigation displays in the EVIC.
200 UNDERSTANDING YOUR INSTRUMENT PANEL Driver-Selectable Surround Sound (DSS) – If Equipped Press and release the MENU button until “Surround Sound” displays in the EVIC. The EVIC provides infor- mation on the current surround mode. • Stereo • Video Surround •...
Personal Settings (Customer Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in PARK. Press and release the MENU button until Personal Set- tings displays in the EVIC. Use the SCROLL button to display one of the following choices.
Page 204
202 UNDERSTANDING YOUR INSTRUMENT PANEL “Remote Key Unlock” When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE UNLOCK button twice to unlock the passenger’s doors.
Page 205
NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in Section 3. “Delay Turning Headlights Off” When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
204 UNDERSTANDING YOUR INSTRUMENT PANEL “Turn-by-Turn Navigation” — If Equipped When ON is selected, the turn-by-turn directions will appear in the display as the vehicle approaches a desig- nated turn within a programmed route. To make your selection, press and release the FUNCTION SELECT button until “ON”...
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
206 UNDERSTANDING YOUR INSTRUMENT PANEL An auxiliary input jack permits passengers to listen to a portable MP3 player through the vehicle’s speakers. For vehicles equipped with the Vehicle Entertainment System (VES) , separate audio outputs allow passengers to listen to the vehicle speakers while different audio tracks play through the system’s wireless headphones.
Clock Setting Procedure Setting the Clock 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. To move the hour forward, touch the screen where the word “Hour”...
Page 210
208 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the multimedia system is turned off. Proceed as follows to change the current setting: 1.
SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. REQ Radio UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 212
210 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station, in AM, FM or Satellite (if...
Page 213
3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5.
Page 214
212 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
Page 215
16-Digit Character Program Type Jazz News Nostalgia Nostalga Oldies Personality Public Rhythm and Blues Religious Music Rel Musc Religious Talk Rock Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Talk UNDERSTANDING YOUR INSTRUMENT PANEL 213 Program Type Display Jazz Top 40...
Page 216
214 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select between the following items: NOTE: Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/SELECT button to select an entry and make changes. •...
Page 217
• VES™ Lock - Locks out rear VES™ remote controls (if equipped). • VES™ CH1/CH2 - Allows the user to change the mode of either the IR1 or IR2, wireless headphones by pressing the AUDIO/SELECT button (if equipped). • Set Home Clock - Pressing the SELECT button allows you to set the clock.
Page 218
216 UNDERSTANDING YOUR INSTRUMENT PANEL Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting other.
SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button.
Page 220
218 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components.
Press and hold the eject button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF. SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD.
Page 222
220 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally.
Page 223
When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
222 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3/WMA files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs •...
Page 225
Press and hold the INFO button again for three seconds to return to elapsed time display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 226
224 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. For UConnect “Voice Recognition System (VR),” refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Hands-Free Phone (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )”...
SALES CODE RER — MULTIMEDIA SYSTEM — IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The RER Multimedia system contains a radio, Sirius Satellite Radio player, navigation system, CD/DVD player, USB port, 20-gigabyte hard drive (HDD), and the UConnect Hands-Free Bluetooth cellular system.
226 UNDERSTANDING YOUR INSTRUMENT PANEL Other special features include direct tune, music type selections, traffic messaging (optional), easy store presets, parental lockout for VES™ (if equipped), backup camera display for vehicles equipped with a backup camera, and on some models, a dual display screen operation. Refer to your “Navigation User’s Manual”...
Page 229
4. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 5. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you want to select, touch the screen where the word “Page”...
Page 230
228 UNDERSTANDING YOUR INSTRUMENT PANEL 3. If the words “Time: GPS Time” are displayed at the top of the screen, touch the bottom of the screen where the words “GPS Time” are displayed. The user clock time setting menu will appear on the screen. 4.
SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. RES Radio (Non-Satellite Model Shown - With Satellite Similar) UNDERSTANDING YOUR INSTRUMENT PANEL 229 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 232
230 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Page 233
TIME Button Press the TIME button and the time of day will display. In AM or FM mode, pressing the TIME button will switch between the time and frequency displays. Clock Setting Procedure 1. Press and hold the TIME button, until the hours blink. 2.
232 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones.
Page 235
Toggle the MUSIC TYPE button to select the following format types: 16-Digit Character Program Type No program type or un- defined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies UNDERSTANDING YOUR INSTRUMENT PANEL 233 Program Type Personality Display...
Page 236
234 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
stations to be stored into pushbutton memory. The sta- tions stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations).
Page 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism.
SCAN Button Press the SCAN button to scan through each track on the CD currently playing. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title.
Page 240
238 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally.
Page 241
Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs •...
Page 243
Press and hold the INFO button again for three seconds to return to elapsed time display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
242 UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO (RSC) — IF EQUIPPED (RER/REQ/REN RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios.
Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With REQ Radios With the ignition switch in the ON/RUN or ACC posi- tion and the radio ON, press the SETUP button and scroll using the TUNE/SCROLL control knob until Sirius ID is selected.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
Page 247
three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows.
246 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button.
SIRIUS BACKSEAT TV™ — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video coast to coast. The subscription service provider is SIRIUS Satellite Radio. SIRIUS Backseat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting studios.
Page 250
248 UNDERSTANDING YOUR INSTRUMENT PANEL Opening the Rear Seat VES • The LCD Screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display. VES Video Screen NOTE: Close the armrest after the LCD screen has been raised to its viewing position.
Page 251
• A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. VES Remote Control • Two wireless infrared headsets allow rear seat passen- gers to listen to the same or individual audio sources. UNDERSTANDING YOUR INSTRUMENT PANEL 249 Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable...
250 UNDERSTANDING YOUR INSTRUMENT PANEL Kicker 13-speaker High Performance Sound System with Driver-Selectable Surround (DSS) – If Equipped Your vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surround sound from any stereo audio source. A new feature of the Kicker audio system offers the ability to choose surround sound for any audio source or video source.
are “Stereo,” “Audio Surround,” and “Video Surround.” When in Video Surround mode, balance and fade are set automatically by the KMS1 system to provide the ultimate surround sound experience. UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED NOTE: This section is for sales code RES and REQ radios only with UConnect .
252 UNDERSTANDING YOUR INSTRUMENT PANEL Controlling The iPod Using Radio Buttons To get into the UCI (iPod ) mode and access a connected iPod , press the AUX button on the radio faceplate. Once in the UCI (iPod ) mode, the iPod available from iPod ) will start playing over the vehicle audio system.
Page 255
Pressing and releasing the FF button will go forward five seconds of the current track. SEEK Buttons Use the SEEK buttons to move to the previous or the next track. If the left (down) button is pressed during the first two seconds of the current track, it will go back to the previous track in the list;...
254 UNDERSTANDING YOUR INSTRUMENT PANEL List or Browse Mode During Play mode, pressing any of the following buttons will take you to List mode. List mode enables you to scroll through the list of menus and tracks on the iPod device.
After pressing a preset button, you will see the list you are in on the top line and the first item in that list on the second line. To exit the List mode without selecting a track, press the same preset button again to go back to Play mode. LIST Button Pressing the LIST button will take to the top level menu of the iPod .
Page 258
256 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with steering wheel-mounted buttons are also equipped with the Electronic Vehicle Information Center (EVIC). The EVIC features a driver-interactive display. This is located in the instrument cluster below the speedometer. The VOLUME button controls the sound level of the sound system.
CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3.
258 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Manual Temperature Controls Blower Control The rotary knob on the left controls the blower.
Page 261
Mode Control The rotary knob on the right controls airflow distribution. Dots between each of the mode selections identify intermediate modes that allow the op- erator to fine-tune airflow distribu- tion. The mode settings are as follows: • Defrost Air is directed to the windshield through the outlets at the base of the windshield.
260 UNDERSTANDING YOUR INSTRUMENT PANEL • Recirculation Control The mode control knob also controls the recirculation feature. You can choose Bi- Level Recirculation air outlets, Panel Recir- culation air outlets, or a mix or both while in this mode. Normally, air enters from outside the vehicle.
Page 263
the controls on the climate control, from a dual sun- sensor located in the top of the instrument panel, from an infrared sensor located in the face of the climate control, and from various sensors located throughout the vehicle. The controls on the climate control provide the system with operator input.
Page 264
262 UNDERSTANDING YOUR INSTRUMENT PANEL Air conditioning in this system is automatic. Pressing the air conditioning control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and request- ing the air conditioning is not necessary.
Page 265
Manual Operation This system offers a full complement of manual override features, which consist of blower preferred automatic, mode preferred automatic, or blower and mode preferred automatic. This means the operator can override the blower, the mode, or both. There is a manual blower range for times when the AUTO setting is not desired.
Page 266
264 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 267
The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles.
266 UNDERSTANDING YOUR INSTRUMENT PANEL Press this button a second time to turn off the air conditioning. An LED in the button illuminates when manual compressor operation is selected. NOTE: To control the air conditioning manually, the mode selector must be moved out of the AUTO position. •...
Page 269
Winter Operation Use of the air Recirculation mode during Winter months is not recommended because it may cause window fogging. Vacation Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
Page 270
268 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
REAR WINDOW FEATURES Rear Wiper Operation The rear wiper is operated by the rear wiper/ washer switch. The switch is located in the switch bank near the top center of the instrument panel. An indicator in the switch illuminates when the rear wiper is To use the rear wiper, push the left side of the rear wiper/washer switch in and release.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Adding Washer Fluid The windshield washer and rear window washer share the same fluid reservoir. The reservoir is located in the front of the engine compartment on the passenger side of the vehicle. Be sure to check the fluid level at regular intervals.
WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Electric Rear Window Defroster The Electric Rear Window Defroster control is located on the climate control. Press this button to turn ON the rear window defroster and the heated outside rearview mirrors (if equipped).
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. STARTING AND OPERATING 277 WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
278 STARTING AND OPERATING Automatic Transmission The shift lever must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting into any driving gear. CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: •...
Normal Starting (Tip Start) NOTE: Normal Starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages.
280 STARTING AND OPERATING If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. •...
After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord.
282 STARTING AND OPERATING WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
Page 285
• The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating. Therefore, the first few shifts on a new vehicle may be somewhat abrupt or soft until after the break-in period. This is a normal condition, and pre- cision shifts will develop within a few shift cycles.
284 STARTING AND OPERATING Over-Temperature Mode The transmission electronics constantly monitor the trans- mission oil temperature. If the transmission exceeds nor- mal operating temperature, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation in DRIVE position.
To activate the override, first insert the key into the ignition switch and turn it to the ACC or ON position. Then, press the pink-colored tab trough the access pot with a small flat blade screwdriver or alike. While pressing the override, move the shift lever out of the PARK position.
Page 288
286 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK.
Page 289
NEUTRAL In NEUTRAL, no power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). The engine may be started in this range.
Page 290
288 STARTING AND OPERATING When frequent transmission shifting occurs when using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing heavy trailers, use the AutoStick mode and select the “3” range. AutoStick Gear Selection The AutoStick feature can be selected by pressing the shift lever to the right or the left with the lever in the...
Page 291
Delayed Shifts in Cold Temperatures During cold temperature operation, you may notice delayed upshifts depending on engine and transmission temperature as well as vehicle speed. This feature im- proves warm up time of the engine and transmission to achieve maximum efficiency. Temporary Transmission Limp Home Mode The transmission is monitored for abnormal conditions.
290 STARTING AND OPERATING Have the transmission checked at your authorized dealer as soon as possible. If the problem has been momentary, the transmission can be reset to regain all forward gears. Permanent Transmission Limp Home Mode Permanent Limp Home Mode will be activated if the transmission enters temporary Limp Home Mode three times.
NOTE: • In Autostick mode, the transmission will only shift up and down when the driver manually moves the shift lever Right (D+) or Left (D-). • An UPSHIFT message will appear in the Electronic Vehicle Information Center (EVIC) portion of the in- strument cluster when using Autostick .
292 STARTING AND OPERATING • Transmission shifting will be more noticeable when Autostick is engaged. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the rear wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the rear (driving) wheels.
DRIVING THROUGH WATER Driving through water more than a few inches/ millimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off).
Page 296
294 STARTING AND OPERATING CAUTION! • Driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
PARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle. WARNING! Never use PARK position on an automatic transmis- sion as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
Page 298
296 STARTING AND OPERATING Parking Brake The brake light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is ON. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. WARNING! •...
BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. There will be some loss of overall braking effectiveness. This may be evident by increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.
Page 300
298 STARTING AND OPERATING ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. You also may experience the following when the brake system goes into Anti-lock: •...
All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer. Anti-Lock Brake Light The ABS light monitors the Anti-Lock Brake Sys- tem. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
300 STARTING AND OPERATING Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.
ABS (Anti-Lock Brake System) This system aids the driver in maintaining vehicle control under adverse braking conditions by controlling hydrau- lic brake pressure. This prevents wheel lock-up to help avoid skidding on slippery surfaces during braking. For more information about ABS, refer to “Anti-Lock Brake System”...
302 STARTING AND OPERATING TCS (Traction Control System) This system monitors the amount of wheel spin of each driven wheel. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. BAS (Brake Assist System) This system complements the Anti-Lock Brake System (ABS) by optimizing the vehicle braking capability dur-...
ESP (Electronic Stability Program) This system enhances directional control and stability of the vehicle under various driving conditions. The ESP corrects for oversteering and understeering the vehicle by applying the brake of the appropriate wheel. Engine power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path.
Page 306
304 STARTING AND OPERATING WARNING! The ESP (Electronic Stability Program) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
Page 307
NOTE: To improve the vehicle’s traction when driving with snow chains, or when starting-off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily depressing the “ESP OFF” button. Once the situation requiring “Partial Off” mode is overcome, turn the ESP ON again by momen- tarily depressing the “ESP OFF”...
306 STARTING AND OPERATING NOTE: When the ESP is switched off a feature of the system remains active. This feature controls wheel spin across an axle quite similarly to a limited slip differential. If one wheel on an axle is spinning faster than the other, the system will apply the brake of the spinning wheel and allow more engine torque to be applied to the wheel that is not spinning.
Indicator Light should go out. However, if the light remains on, have the ESP and BAS checked at your authorized dealer as soon as possible. ESP/BAS Malfunction Indicator Light and ESP/TCS Indicator Light The Malfunction Indicator Light for the ESP is combined with the BAS indicator.
308 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 311
Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%).
Page 312
310 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —The maximum speed corresponding to the speed symbol should only be achieved un- der specified operating conditions (i.e., tire pressure, vehicle loading, road conditions,...
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
312 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-pillar. Tire Placard Location Tire and Loading Information Placard Tire And Loading Information Placard This placard tells you important information about: 1) number of people that can be carried in the vehicle...
Page 315
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 316
314 STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) {(since 5 x 150 = 750, and 1400 –...
316 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 320
318 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
320 STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). Refer to the paragraph on “Freeing A Stuck Vehicle” in Section 6. WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure.
These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
322 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed.
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
324 STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four. Failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).
326 STARTING AND OPERATING Tire Rotation — All Season Tires The suggested rotation method for vehicles equipped with all season tires is the “forward-cross” as shown in the following diagram.
TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C).
Page 330
328 STARTING AND OPERATING vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. − For example, your vehicle may have a recom- mended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa).
NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. •...
Page 332
330 STARTING AND OPERATING The matching full size spare wheel and tire assembly (if equipped) has a tire pressure monitoring sensor. The matching full size spare can be used in place of any of the four road tires. The TPMS will only monitor the pressure in the full size spare when it is used in place of a road tire.
Page 333
3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: Vehicles with Full Size Spare 1. The matching full size spare wheel and tire assembly has a tire pressure monitoring sensor that can be moni- tored by the TPMS.
332 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically and the TPM Telltale Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires.
Page 335
Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display one or more low pressure messages (Left Front, Left Rear, Right Front, Right Rear) for three seconds and a graphic showing the pressure values of...
Page 336
334 STARTING AND OPERATING Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flash- ing, and the Tire Pressure Monitoring Telltale Light will...
Page 337
If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, and the CHECK TPM SYS- TEM message will no longer display, and a pressure value will display in place of the dashes.
Page 338
336 STARTING AND OPERATING NOTE: Vehicles with Compact Spare 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, the TPM Telltale Light will remain ON and a chime will sound.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
338 STARTING AND OPERATING Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World- wide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasolines that meet the WWFC speci- fications, if they are available.
manufacturer. While MTBE is an oxygenate made from methanol, it does not have the negative effects of metha- nol. MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.
340 STARTING AND OPERATING • An out-of-tune engine or certain fuel or ignition mal- functions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunc- tioning and may require immediate service.
• Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk/liftgate closed when driving your vehicle to prevent carbon monoxide and other poison- ous exhaust gases from entering the vehicle.
Page 344
342 STARTING AND OPERATING Gas Cap Tether Hook CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system.
WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle.
344 STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Do not exceed the specified Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR).
WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory...
Page 348
346 STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that neither the GVWR nor the GAWR capacities have been exceeded. EXAMPLE ONLY Empty Weight Load (including driver, pas- sengers, and cargo) Total GAWR NOTE: Refer to the “Vehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR and GAWRs.
TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.
Page 350
348 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The Gross Axle Weight Rating (GAWR) is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR.
Page 351
Weight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturers directions, it pro- vides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
Page 352
350 STARTING AND OPERATING Weight Distributing Hitch System Improper Adjustment of Weight Distributing System...
Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
352 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission 6.1L Automatic Refer to local laws for maximum trailer towing speeds NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and it should never exceed the weight referenced on the “Tire Frontal Area...
Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer.
354 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information”...
Page 357
WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel. When traile- ring cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 358
356 STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized. (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) Towing Requirements — Tires −...
Page 359
actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 360
358 STARTING AND OPERATING Towing Requirements — Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4- and 7-pin wiring harness.
7-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. STARTING AND OPERATING 359 Towing Tips — Automatic Transmission The DRIVE range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the “3”...
Page 362
360 STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat Towing With All Four Wheels On The Ground) Recreational towing for this vehicle is not recommended. NOTE: If the vehicle requires towing, make sure all four wheels are off the ground. STARTING AND OPERATING 361 GROUND CLEARANCE CAUTION!
364 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The HAZARD switch is located in the switch bank near the top center of the instrument panel. De- press the switch to activate the flashers. When activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (116°C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–110°C).
Page 368
366 WHAT TO DO IN EMERGENCIES The TIREFIT system is located under a hinged access cover in the load floor in the cargo area. TIREFIT Location TIREFIT contents 1. Air pump hose 2. Power plug and cable 3. AIR PUMP switch 4.
Page 369
WARNING! • Do not attempt to repair a tire on the side of the vehicle close to traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or repairing a tire. • Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pres- sure or on a flat tire, or a damaged wheel can pose a hazard while driving.
Page 370
368 WHAT TO DO IN EMERGENCIES 7. Leave the parking brake set and the shift lever in PARK and start the engine. 8. Press the switch (3) on the air pump to I (ON). The air pump should start to inflate the tire and the tire sealant (white fluid) will flow from the sealant bottle (5) through the TIREFIT sealant hose (6) and into the tire.
Page 371
18. With a tire pressure of no less than 26 psi (1.8 bar) press the AIR PUMP switch (3) to 0 (OFF) and turn off the engine. Then, disconnect the TIREFIT system from the tire and place it back in the vehicle. 19.
Page 372
370 WHAT TO DO IN EMERGENCIES Close the load floor cover. Replace the sealant bottle at your nearest authorized MOPAR parts dealership. 29. Have the tire inspected at the earliest opportunity at an authorized dealer or tire service center. NOTE: •...
JUMP-STARTING PROCEDURES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
Page 374
372 WHAT TO DO IN EMERGENCIES 3. Set the parking brake, place the automatic transmis- sion in PARK, and turn the ignition switch to the LOCK position on both vehicles. 4. Turn off the heater, radio, and all unnecessary electri- cal loads.
Page 375
WARNING! • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharged battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are be- low the freezing point, electrolyte in a discharged battery may freeze.
374 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
376 WHAT TO DO IN EMERGENCIES CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • If the transmission is not operative or if the vehicle is to be towed more than 30 mi (48 km), then the only approved method of towing is with a flat-bed truck.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
382 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic Vehicle Information Center (EVIC) (if equipped). If this occurs, tighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message.
Page 385
3. If you crank or start the engine, you will have to start this test over. 4. As soon as you turn your key to the ON position, you will see the MIL symbol come on as part of a normal bulb check.
384 MAINTAINING YOUR VEHICLE REPLACEMENT PARTS Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-MOPAR parts for maintenance and repairs will not be covered by the manufacturer’s warranty.
These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight.
Page 388
386 MAINTAINING YOUR VEHICLE Change Engine Oil Refer to the Maintenance Schedule in Section 8. NOTE: Under no circumstances should oil change intervals exceed 6,000 mi (10 000 km) or six months, whichever occurs first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or...
The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “Engine Com- partment” illustration in this section. Materials Added to Engine Oil The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to the engine oil.
388 MAINTAINING YOUR VEHICLE Inspect belts for evidence of cuts, cracks, glazing, or frayed cords and replace if there is indication of damage that could result in belt failure. Also, check belt routing to make sure there is no interference between the belts and other engine components.
Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, filter replacement may be necessary. See your authorized dealer for service.
390 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
Page 393
NOTE: The battery is stored under a hinged access cover in the load floor in the cargo area. Remote battery terminals are located in the engine compartment for jump-starting. Battery Location MAINTAINING YOUR VEHICLE 391 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you.
392 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and identified on the battery case.
WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
394 MAINTAINING YOUR VEHICLE filter. Install the new filter with arrows pointing in the direction of airflow, which is toward the rear of the vehicle (text and arrows on the filter indicate this). Refer to the Maintenance Schedule in Section 8 for the recommended air conditioning filter replacement inter- vals.
Steering Linkage The tie rod end ball joints should be inspected for external leakage or damage when other maintenance is performed. Body Lubrication Locks and all body pivot points, including seat tracks, door hinges, liftgate hinges, and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
396 MAINTAINING YOUR VEHICLE Windshield Washers/Rear Window Washer The windshield washer and the rear window washer share the same fluid reservoir. The fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change.
Page 400
398 MAINTAINING YOUR VEHICLE Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
Page 401
CAUTION! • Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the speci- fied coolant as soon as possible.
Page 402
400 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where...
Page 403
Disposal of Used Coolant Used ethylene glycol-based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground.
402 MAINTAINING YOUR VEHICLE • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing.
Ensure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
Page 406
404 MAINTAINING YOUR VEHICLE Brake and Power Steering Hoses When the vehicle is serviced for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling indicate deterioration of the rubber.
Page 407
Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system fail- ure. Check the fluid level in the master cylinder when per- forming underhood services. Clean the top of the master cylinder area before removing the cap.
406 MAINTAINING YOUR VEHICLE CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid. Seal damage may result. Automatic Transmission Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.
Fluid and Filter Changes Refer to the Maintenance Schedule in Section 8 for the recommended transmission fluid and filter change inter- vals. If the transmission is disassembled for any reason, the fluid and filter should be changed. Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance.
408 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 411
• Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
Page 412
410 MAINTAINING YOUR VEHICLE • Use Mopar touch up paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 413
WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
412 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag or micro-fiber towel. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2.
FUSES (POWER DISTRIBUTION CENTERS) Fuses (Front Power Distribution Center) A power distribution center is located in the engine compartment. This center contains fuses and relays. Front Power Distribution Center MAINTAINING YOUR VEHICLE 413 CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Cavity Car- Mini- Description tridge Fuse Fuse — — — — — — — — — Fuses (Rear Power Distribution Center) There is also a power distribution center located under a hinged access cover in the load floor in the cargo area. This center contains fuses and relays.
Page 418
416 MAINTAINING YOUR VEHICLE Rear Power Distribution Center CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure.
Page 419
Cavity Car- Mini- Description tridge Fuse Fuse 60 Amp — Ignition Off Draw (IOD) Yellow 40 Amp — Integrated Power Mod- Green ule (IPM) — — — 40 Amp — Integrated Power Mod- Green ule (IPM) 30 Amp — Heated Seats - if Pink equipped —...
420 MAINTAINING YOUR VEHICLE fused by the 25-amp circuit breaker in cavity 11. The passenger SEAT switch is fused by the 25-amp circuit breaker in cavity 12. The door modules, the driver power WINDOW switch, and the passenger power WINDOW switch are fused by the 25-amp circuit breaker in cavity 13.
All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS — Exterior Low Beam Headlight ..... 9006 High Beam Headlight.
Page 424
422 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Disconnect the bulb from the socket assembly and install the replacement bulb.
Low Beam Headlight, High Beam Headlight, and Park/Turn Light — Models with High Intensity Discharge Headlights (HID) High Intensity Discharge Headlights (HID The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed.
Page 426
424 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Disconnect the bulb from the socket assembly and install the replacement bulb.
Tail/Stop, Turn Signal Light, and Backup Light 1. Open the liftgate. 2. Remove tail light access cover. 3. Push the electrical connector locking tab to the side. 4. Disconnect the electrical connector. MAINTAINING YOUR VEHICLE 425 5. Remove one wing nut from the back of the tail light assembly.
Page 428
426 MAINTAINING YOUR VEHICLE 8. Turn the appropriate bulb and socket assembly coun- terclockwise to remove it from the tail light assembly. 2 — Turn Signal Light Bulb 1 — Tail/Stop Light Bulb...
Page 429
MAINTAINING YOUR VEHICLE 427 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 11. Reinstall the tail light assembly, fasteners, and elec- trical connector.
428 MAINTAINING YOUR VEHICLE License Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 1 — License Light Bulb 2 —...
430 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (6.1L) Oil Filter (6.1L) Spark Plugs (6.1L) Fuel Selection (6.1L) Fluids, Lubricants, and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or SM/CF, and...
Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Rear Axle Fluids, Lubricants, and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Page 435
MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..434 Maintenance Schedule ....434 Severe Duty ......436 Required Maintenance Intervals .
434 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services, listed in bold type , must be done at the times or mileages specified to ensure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 437
At Each Stop for Fuel • Check the engine oil level. Refer to “Engine Oil” under “Maintenance Procedures” in Section 7. • Check the windshield washer solvent and add if required. Once a Month • Check tire pressure and look for unusual wear or damage.
436 MAINTENANCE SCHEDULES Severe Duty If your vehicle is operated under the Severe Duty condi- tions listed below change your engine oil and filter every 3,000 mi (5 000 km) or three months as indicated in the Maintenance Schedule. • Stop and go driving. •...
Required Maintenance Intervals Maintenance Items Change the engine oil and engine oil filter if using your vehicle under any of these severe duty condi- tions: Short trips, stop and go driving, dusty or off- road conditions, police, taxi, fleet, or frequent trailer towing.
Page 440
438 MAINTENANCE SCHEDULES Maintenance Items Replace the air conditioning filter (if equipped). Inspect the rear axle fluid. Inspect the CV joints. Perform the first inspection at 12,000 mi (20 000 km) or 12 months. Inspect the exhaust system. Perform the first inspec- tion at 12,000 mi (20 000 km) or 12 months.
Page 441
Maintenance Items Inspect and replace PCV valve if necessary. Flush and replace the engine coolant. Replace the spark plugs. Change the automatic transmission fluid and filter. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......443 Prepare For The Appointment .
Page 444
442 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....447 Department Of Transportation Uniform Tire Quality Grades ......448 Treadwear .
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
444 IF YOU NEED CONSUMER ASSISTANCE special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be re- solved with this process.
Customer Assistance for the Hearing or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
446 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Adminis- trator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
448 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
All passenger car tires must conform to Federal safety requirements in addition to these grades. Treadwear The treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 1-1/2 times as well on the government course as a tire graded 100.
450 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 458
456 INDEX Selection of Coolant (Antifreeze) ..398,429,430 Corrosion Protection ..... 408 Cruise Control (Speed Control) ....138 Cruise Light .
Page 459
Electronic Stability Program (ESP) ... . 303 Electronic Throttle Control Warning Light ..176 Electronic Vehicle Information Center (EVIC) ..185 Emergency, In Case of Freeing Vehicle When Stuck .
Page 460
458 INDEX Exhaust System ..... . . 74,396 Exterior Folding Mirrors ....85 Exterior Lighting .
Page 472
470 INDEX High Speed ......319 Inflation Pressures ..... 317 Life of Tires .
Page 473
Shifting ......281 Transmitter Battery Service (Remote Keyless Entry) ....23 Transmitter, Garage Door Opener (HomeLink ) .
Page 474
472 INDEX Warning Lights (Instrument Cluster Description) ......175 Warnings and Cautions ..... 6 Warranty Information .
Page 475
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 476
81-226-0822 First Edition Printed in U.S.A.
Need help?
Do you have a question about the 2008 DX-49 Magnum SRT8 and is the answer not in the manual?
Questions and answers