Reset And Set For Suplly Counters; Location And Display Of Each Counter Data - Sharp AR-M550N Service Manual

: Feb. 9 2004
1

(10)Reset and set for suplly counters

Work item
Setting the toner concentration control level
Reset the OPC drum counter
Reset the Developer counter
Reset the OPC drum running time counter (sec)
Reset the DV running time counter (sec)
B. Location and display of each counter data
Simulation
Code
Operation content
Main Sub
22 01 Each counter display (Total/ Mainte-
nance/ Developer/ SPF/ Staple/ Tray)
1: Total counter
1
2: Drum cartridge counter
3: Toner cartridge counter
4: Deve cartridge counter
5: Maintenance counter
6: Total output page number counter
7: Copy counter
8: Printer counter
9: FAX output counter
10: I-FAX output counter
11: Document filing output counter
12: Right side output counter
13: Other print counter
02 Jam/ Trouble counter display
1: Paper jam
2: SPF jam
3: Trouble
08 Document, staple counter display
1: SPF document feed page number
2: Scan number
3: Staple number
4: Punch number
5: SPF finish stamp number
6: Saddle staple number
7: Inserter number
09 Paper feed counter display
1: Paper feed tray 1 (Tandem Left)
2: Paper feed tray 2 (Tandem Right)
3: Paper feed tray 3
4: Paper feed tray 4
5: MFT (Manual paper feed tray)
6: ADU
7: LCC
11 FAX send/receive counter display
1: FAX send (Send counter)
2: FAX receive (Receive counter)
3: FAX output (FAX print counter)
4: FAX send images (Send page
number)
5: Send time (Send time)
6: Receive time (Receive time)
Test Command
Sim25-2
Sim24-7
Sim24-5
Sim24-11
Sim24-11
Data location
Data
MFP Scanner
size PCU
control FAX control
PWB
PWB PWB
32bit
32bit
32bit
32bit
48bit
48bit
AR-M550/M620/M700 OTHER 12 - 5
Reset item
Developer counter
DV unit running time counter (sec)
OPC drum counter
Developer counter
OPC drum running time counter (sec)
DV running time counter (sec)
Conforming count mode
(SIM 26-5)
Mainte-
TOTAL DV
nance
Count is made when the main unit paper exit is started. (When POP2
is ON)
Refer to the "Count Specifications."
— — — Count is made when an event occurs. (A jam by closing the door dur-
ing paper transport is not counted.)
— — — Count is made when an event occurs. (A jam by closing the door dur-
ing paper transport is not counted.)
— — — Count is made when an event occurs. (Follows the trouble count
method of SIM 26-35.)
— — — One count is made every time when SPF document is paper feed.
— — — One count is made every time when scan is completed.
— — — One count for every stapling (Stapling at two positions is counted as
2.)
— — — One count for every punching
— — — One count when stamp is started.
One count for every saddle stapling
One count for every paper pick-up
— — — One count for every paper pick-up
— — — One count for every paper pick-up
— — — One count for every paper pick-up
— — — One count for every paper pick-up
— — — One count for every paper pick-up
— — — One count for every paper transport start from ADU.
One count for every paper pick-up
— — — Accumulated page number of send
• Except for the serial transmit operation, one reservation is counted
as one communication.
• For the serial transmit operation, count is made for each communi-
cation individually.
• Recall is not included.
• Saved in the FAX-SRAM.
— — — Accumulated number
• Count is made regardless of normal or abnormal completion.
• Saved in the 32bit counter and the FAX-SRAM.
The accumulated page number of FAX receive print
Count by size and count in recovery are the same as the copier spec-
ifications.
• Counted by the print system.
Refer to the "Count Specifications."
— — — Accumulated page number of send
• In the serial transmit operation, each communication is counted as
one individually.
• Saved in the 32bit counter and the FAX-SRAM.
— — — hhhhhhhh:mm:ss
Saved in the FAX-SRAM.
— — — hhhhhhhh:mm:ss
Saved in the FAX-SRAM.
Included Test Command
Sim24-5
Sim24-11
—
—
—
—
Count-up condition