Sharp AR-M550N Service Manual page 246

: Feb. 9 2004
1
Item
3 AE 3.0 AE mode
4 CH 3.0 Text mode 3.0
5 MIX 3.0 Text/Photo mode 3.0
6 PHOTO 3.0 Photo mode 3.0
3) Using the numeric keypad, select the number that corresponds to
the copy mode for which to make adjustments. (Choose from
numbers 3 to 6.)
4) Press the Start key
5) Press the Start key (A copy is created.)
Check the density of the copied image.
If the copied image density is not at an acceptable level, do the fol-
lowing steps.
6) Adjust the copy density by entering an appropriate value through
the numeric keypad.
A larger value provides higher density.
7) Press the P or Start key
This applies the adjustment value.
Pressing the Start key starts copy operation as well as applying the
adjustment value.
8) Check the copied image density.
Repeat steps 6 to 8 until an acceptable copied image density is
obtained.
Note: Adjusting the copied image density through this simulation
changes the copied image density settings for all copy modes to
the copied image density level applied by carrying out this simu-
lation. Also, the copied image density gradient is automatically
adjusted to the specified level.
The copied image density settings for individual copy modes
adjusted through Simulations 46-9, -10, and -11 are changed to
the copied image density level applied by this simulation.
ADJ 9B Adjust the copy density in text binary
mode
ADJ 9C Adjust the copy density in text/photo
binary mode
ADJ 9D Adjust the copy density in photo binary
mode
This adjustment is intended to customize the copied image density set-
tings. The copy density setting for each copy density adjustment level
(1 to 5) in manual copy mode can be adjusted to a custom density
level.
1) Set the test chart (UKOG-0162FCZZ) on the original table.
2) Go through the simulation modes that correspond to the copy
modes for which to adjust the copy density (i.e., the modes speci-
fied in Simulations 46-9, -10, or -11).
Set
Default
range
0 - 99 50
AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 31
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. 1.0 50 4. 1.5 50
6. 2.5 50 7. 3.0 50
9. 4.0 50 10. 4.5 50
Select other than 0 - 2, and
press [START] key.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). INPUT VALUE 0-99, AND PRESS
START.
3. 1.0
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). NOW COPYING.
Select 0, and
press [START] key.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). SELECT 1-6, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2
5. BPT 6. LCC
Select 2, and press [START] key.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START.
(EXP. LEVEL SELECT)
3. 1.0 4. 1.5
6. 2.5 7. 3.0
9. 4.0 10. 4.5
(SIM 46-9) (Text mode)
Item
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 EXP LEVEL Exposure level selection
3 1.0 Exposure level 1.0
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
1
5. 2.0 50
8. 3.5 50
11. 5.0 50
Press
[CUSTOM SETTINGS] key.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [CUSTOM SETTINGS] key.
3. TRAY3 4. TRAY4
1
Press [START] key, or
press [CUSTOM SETTINGS] key.
5. 2.0
8. 3.5 1
11. 5.0
Set
Default
range
0 - 99 50