Sharp AR-M550N Service Manual page 328

1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
Set range 25 - 200 (%)
(Table 1)
Item
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 MAGNIFICATION Print magnification ratio
(Lead edge adjustment value)
3 SIDE1 Front surface document
scan start position
adjustment value
4 SIDE2 Back surface document
scan start position
adjustment value
(Image loss set value: SIDE 1)
5 LEAD_EDGE Front surface lead edge
image loss set value
6 FRONT_REAR Front surface side edge
image loss set value
7 TRAIL_EDGE Front surface rear edge
image loss set value
(Image loss set value: SIDE 2)
8 LEAD_EDGE Back surface lead edge
image loss set value
9 FRONT/REAR Back surface side edge
image loss set value
10 TRAIL_EDGE Back surface rear edge
image loss set value
(Table 2)
Normal display
ERROR display Door open
Jam
Paper empty
(Table 3)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
6 LCC
When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.
Set
Default
range
1 - 6 –
– –
25 - –
200%
0 - 99 50
0 - 99 15
20
0 - 20 0
0 - 99 15
20
0 - 20 0
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
Side LCC
AR-M550/M620/M700 SIMULATION 8 - 70
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
(ADJUSTMENT DATA)3.SIDE1
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE 15
SIDE2: 8.LEAD_EDGE 15
Select other than 0 - 2, and press [START] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS
START.
3.SIDE1
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.
Select 0, and press [START] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Select 2, and
press [START] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF).
(MAGNIFICATION)
INPUT 25-200(%)
50-7
Purpose Adjustment
Function Used to adjust the copy image position and void area
(Purpose) (image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-6.)
(SPF mode)
Section
Item Picture quality
Operation/Procedure
(Lead edge image loss adjustment)
1) Set the front and back surface image loss adjustment values
(LEAD EDGE) as specified below:
(Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)
Paper lead edge void: 3.5mm (DENA: 35)
∗ Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD EDGE, and press [P] key.)
2) Set the adjustment value of L4 to 0. (Enter 0 as the adjustment
value of L4, and press [P] key.
3) Set the adjustment value of L5 to 0. (Enter 0 as the adjustment
value of L5, and press [P] key.
4) Make a copy at 200% with the SPF, and calculate the values of L4
and L5. (Enter 200 as the set value of the copy magnification ratio
set value (MAGNIFICATION) and press [START] key.)
L4 = Distance (mm) from the image lead edge position to the
scale of 10mm x 10
2
50 4.SIDE2 50
6.FRONT/REAR 20 7.TRAIL_EDGE
9.FRONT/REAR 20 10.TRAIL_EDGE
Press [CUSTOM SETTING] key.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
1
Press [START] key, or
press [CUSTOM SETTINGS] key.
100
0
0