Sharp AR-M550N Service Manual page 319

(Copy condition setting in this simulation)
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value in
this simulation, the adjustment value is set. When START key
is pressed, the adjustment value is set and copying is per-
formed.
Item
0 TRAY SELECT Paper feed tray selection
1: TRAY1
2: TRAY2
3: TRAY3
4: TRAY4
5: Manual feed
6: Side LCC
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3: Exposure level 1.0
4: Exposure level 1.5
5: Exposure level 2.0
6: Exposure level 2.5
7: Exposure level 3.0
8: Exposure level 3.5
9: Exposure level 4.0
10: Exposure level 4.5
11: Exposure level 5.0
3 SPF (FRONT) SPF (front) (front frame side) 0 - 255
4 SPF (REAR) SPF (front) (rear frame side)
5 DSPF DSPF (Back surface)
• "Set value - 128" is added to the shading adjustment value (SIM 46-
17).
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.SPF(FRONT) 128
4.SPF(REAR) 128
5.DSPF 128
Select other than 0 - 2, and press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS
START.
1.SPF(FRONT)
Press [START] key.
Select 1,
Press [CUSTOM SETTINGS] key,
and press
or terminate copying.
[START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT.
Select 0, and
press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-6, AND PRESS START.
(FEED TRAY)
2.TRAY1 2.TRAY2
5.BPT 6.LCC
Select 2, and
press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START.
(EXP. LEVEL SELECT)
3.1.0 4.1.5
6.2.5 7.3.0
9.4.0 10.4.5
Set
Content Default
range
–
–
–
1
Press [CUSTOM SETTINGS] key.
128
NOW PRINTING.
Press [START] key or
press [CUSTOM SETTINGS] key.
3.TRAY3 4.TRAY4
1
Press [START] key or
press [CUSTOM SETTINGS] key.
5.2.0
1
8.3.5
11.5.0
AR-M550/M620/M700 SIMULATION 8 - 61
46-21
Purpose Adjustment
Function Used to adjust the scanner exposure level in all the
(Purpose) scanner modes.
Section
Item Picture quality
Operation/Procedure
1) Select "SCANNER EXP. LEVEL" with 10-key.
2) Press [START] key.
3) Enter the image density adjustment value.
4) Press [P] key or [START] key.
NOTE: When this simulation is performed to adjust the scan image
densities, all the image densities in all the scan modes are
changed to the image density level set with this simulation.
–
That is, the image densities set with SIM 46-22, 23, 24, 25, and
45 are changed to the image density level set with this simula-
tion.
0 SCANNER EXP. LEVEL Image density level
–
NOTE: Only the set value is changed and no printing is performed.
–
SIMULATION 46-21
EXP.LEVEL SETUP SCANNER(AUTO SET), PRESS START.
0.SCANNER EXP.LEVEL
Press [START] key.
128
SIMULATION 46-21
EXP.LEVEL SETUP SCANNER(AUTO SET), INPUT VALUE 0-99,
AND PRESS START.
0.SCANNER EXP.LEVEL
46-22
Purpose Adjustment
Function Used to adjust the scanner exposure level in the
(Purpose) normal text mode.
Section
Item Picture quality
Operation/Procedure
1) Select the number corresponding to one of the following adjust-
ment items with 10-key. (Select one of 0 - 5.)
∗ Normal mode (Image density adjustment level)
∗ Auto mode
2) Press [START] key.
3) Enter the image density adjustment value with 10-key.
4) Press [START] key or press [CUSTOM SETTINGS] key.
The adjustment value is set.
0 AUTO
1 1.0
2 2.0
3 3.0
4 4.0
5 5.0
NOTE: Only the set value is changed and no printing is performed.
Item
50
Press [START] key, or
press [CUSTOM SETTINGS] key.
Set
Item
range
Auto 0 - 99
Exposure level 1
Exposure level 2
Exposure level 3
Exposure level 4
Exposure level 5
Density
Set
Default
range
0 - 99 50
0
50
Density
Default
50