Other; Various Counters Specifications; Count Specification - Sharp AR-M550N Service Manual

: Feb. 9 2004
1

[12] OTHER

1. VARIOUS COUNTERS SPECIFICATIONS]

A. Count specification
(1) Paper exit system counter
Counter
Total counter (Note)
Maintenance counter
Developer counter
All valid paper counter (Note)
Copy counter (Copy valid paper) When paper exit
FAX counter
Print counter
Internet FAX counter
Document filing counter
Right side paper exit counter
Other counter (Self print, etc.)
Large size: A3, 11 x 17. (Greater size than paper length 384mm)
∗ ( ): Count-up number when setting to the large size single count up.
(2) Document, finishing, paper feed system counter
Counter
SPF counter All modes
Finish stamp counter FAX send
Internet FAX send
Staple counter All modes
(Including inserter
stand alone process)
Punch counter All modes
(Including inserter
stand alone process)
Saddle staple counter All modes
(Including inserter
stand alone process)
Scan total counter All modes
ADU counter All modes
Inserter counter All modes
(Including inserter
offline process)
Paper Manual paper All modes
feed feed tray
counter
Paper feed tray 1
Paper feed tray 2
Paper feed tray 3
Paper feed tray 4
LCC
Count-up timing
Paper feed tray – Main
Small size Large size Small size Large size Small size Large size
When transfer is completed
When transfer is completed
When transfer is completed
When paper exit
When paper exit
When paper exit
When paper exit
When paper exit
When center paper exit
When paper exit
Mode Count event
SPF paper
feed number
Finish stamp
use number
Staple
number
Punch
number
Saddle
staple
number
Scan
number
ADU paper
feed number
Inserter tray
paper feed
number
Tray paper
feed number
AR-M550/M620/M700 OTHER 12 - 1
Count-up number
Simplex copy
Paper feed tray – ADU
unit paper exit
1 2 (1) 1
1 2 (1) 1
1 2 (1) 1
1 2 (1) —
1 2 (1) —
1 2 (1) —
1 2 (1) —
1 2 (1) —
1 2 (1) —
1 2 (1) —
1 2 (1) —
Count-up condition
Count is made when starting SPF paper pick.
Count is made when stamp is ON.
Count is made when bundle exit process is completed.
Double count is made when stapling two positions.
In the inserter stand alone mode, count is made when process is
completed.
Count is made when bundle exit process is completed.
1 count regardless of the kind of the punch unit (2-hole, 3-hole, etc.)
In the inserter stand alone mode, count is made when process is
completed.
Count is made when bundle paper exit process is c completed.
Only one count is added.
In the inserter stand alone mode, count is made when process is
completed.
Count is made when scan is completed.
Count is made when paper feed from the ADU section is started.
Count is made when paper feed from the inserter tray is started.
In the inserter stand alone mode, count is made when process is
completed.
Count is made when paper feed from each tray is started.
Duplex copy
ADU – Main unit paper
exit
2 (1) 1 2 (1)
2 (1) 1 2 (1)
2 (1) 1 2 (1)
— 2 4 (2)
— 2 4 (2)
— 2 4 (2)
— 2 4 (2)
— 2 4 (2)
— 2 4 (2)
— 2 4 (2)
— 2 4 (2)
Counter reset
Counter
reset
procedure,
clear
—
Sim24-4
Sim24-5
—
Sim24-6
Sim24-10
Sim24-9
Sim24-15
Sim24-15
—
Sim24-9
procedure,
clear
Sim24-3
Sim24-3
Sim24-3
Sim24-3
Sim24-3
Sim24-3
Sim24-2
Sim24-3
Sim24-2
Sim24-2
Sim24-2
Sim24-2
Sim24-2
Sim24-2