Dif - Panasonic AJ-HD1400E Operating Instructions Manual

Setup menus
(continued)

DIF

No./Item Description of setting
1 For setting the transfer speed of the IEEE1394 digital
880*
interface output.
DIF SPEED
0000 S100 :
100 Mbps
0001 S200 :
200 Mbps
0002 S400 :
400 Mbps
<Note>
When S100 has been selected as this item's setting,
DVCPRO HD format signals cannot be input or
output.
1 For setting the input channel.
882*
0000 0
DIF IN CH
: :
0063 63
The input channel is fixed at the channel
corresponding to the number specified.
0064 AUTO :
The input channel is not fixed at the channel
corresponding to the number specified. The input
channel is initialized to 63 when the power is
turned on.
For setting the output channel.
1
883*
0000 0
DIF OUT CH
: :
0063 63
The input channel is fixed at the channel
corresponding to the number specified.
0064 AUTO :
The output channel is not fixed at the channel
corresponding to the number specified. The output
channel is initialized to 63 when the power is
turned on.
1 Menu item for expansion purposes. Normally, use
886*
DFLT as the setting.
DIF CONFIG
0000 DFLT
0001 1
: :
0255 255
1 For setting the audio channels to which the signals
890*
from the IEEE1394 digital interface are to be output in
DIF AUD OUT
the DV format when a DVCPRO HD tape or 50M
format tape is played back or when a DV tape in 4ch
mode is played by the audio signals and menu No.
891 DIF DV AUDIO is set to "LOCK48."
0000 CH1/2 :
CH1 and CH2
0001 CH3/4 :
CH3 and CH4
1 For setting forcible audio mode conversion when a DV
891*
tape is played back and the audio signals are output
DIF DV
in the DV format.
AUDIO
0000 THRU :
Normal setting (the signals simply pass through).
0001 LOCK :
Forcible conversion to the LOCK mode (no
frequency conversion)
0002 LOCK48 :
Forcible conversion to 48kHz/2CH/LOCK.
No./Item Description of setting
1 For setting how to reply when signals requesting a
892*
confirmation of the format is sent from an external
DIF SIG CMD
device connected by the IEEE1394 digital interface.
0000 50M :
DVDPRO50 is forcibly returned.
0001 25M :
DVDPRO is forcibly returned.
0002 DV :
DV is forcibly returned.
0003 AUTO :
The reply is the same format as the signal format
output from the IEEE1394 digital interface.
<Note>
When the unit is connected to a non-linear editing
system using 50M, 25M, and DV signal format, the
non-linear editing system may not operate properly. In
this case, set the value to reply with the format signal
supporting the connected signal format and start the
system.
1 For selecting channels that are adjusted with the
894*
audio volume control on the front panel and displayed
HD > DIF
on the audio level meter.
OUT
0000 HD :
DVCPRO HD
0001 50M :
DVCPRO50
0002 DV :
DV
1 For setting the format of the signals to be output from
895*
the IEEE1394 digital interface when a 50M format
50M > DIF
tape is played back.
OUT
0000 50M :
DVCPRO50
0001 DV :
DV
<Note>
When DV is selected as this item's setting, the closed
caption signals and time code (VITC) signals in the
vertical blanking period are transmitted, but none of
the other signals in the vertical blanking period are
transmitted.
1 For setting the format of the signals to be output from
896*
the IEEE1394 digital interface when a 25M format
25M > DIF
tape is played back.
OUT
0000 25M :
DVCPRO
0001 DV :
DV
For setting whether the superimposed display is to be
1
899*
output from the IEEE1394 digital interface when the
DIF SUPER
format is converted (from HD to 50M, from HD to DV,
from 50M to DV or from 25M to DV).
0000 OFF :
The superimposed text is not displayed.
0001 ON :
The superimposed text is displayed.
<Note>
Only TCR is displayed.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
"Menus which are displayed" (page 32).
"_____" indicates the factory setting.
53