Download  Print this page

System - Panasonic AJ-HD1400E Operating Instructions Manual

Panasonic digital hd video cassette recorder operating instructions aj-hd1400p, aj-hd1400e
Hide thumbs

Advertisement

Setup menus
(continued)

SYSTEM

No./Item
Description of setting
05
For setting whether to perform the various
adjustments for the video output signals using this
ENCODER
VTR or using an external encoder remote controller.
SEL
0001
LOCAL :
The various adjustments for the video output
signals are performed using this VTR.
0002
BOTH :
The various adjustments for the video output
signals are performed using both this VTR and an
external encoder remote controller.
<Notes>
For video adjustments, refer to "Video output signal
adjustments" (page 35).
If the signals are adjusted with the external
encoder remote controller, the adjusted values are
reflected in the setup menu. However, the adjusted
numerical values will not be stored unless about 1
minute has elapsed after completion of the
adjustment operation. If the unit is turned off after
executing the adjustments with the external
encoder remote controller, it is necessary to wait
about 1 minute before turning off the power.
Settings in this menu are not effective for the
IEEE1394 digital output.
06
For selecting what is to be controlled when the video
output level is to be adjusted by an external encoder
V LEVEL
remote controller.
CTRL
0000
HD :
The HD video output level can be adjusted.
0001
SD :
The SD video output level can be adjusted.
0002
BOTH :
Both the HD and SD video output levels can be
adjusted.
<Note>
When "CMPST" is selected in menu No. 650 STYLE,
the unit will be in the same state as when "BOTH" is
selected, regardless of the settings in this item.
12
For adjusting the system phase of the HD SDI output
signals. (in 13.5 ns increments).
SYS H
– :Phase advances.
(HD)
+ :Phase delays.
0000
–1100
:
:
1100
0
:
:
2200
1100
<Notes>
When menu item No. 25 SYSTEM FREQ is set to
50i/25P, 25 (HD), 25(SD), 50 (HD) or 50 (SD), the
setting range is from –1320 - 0 - 1320.
When menu item No. 25 SYSTEM FREQ is set to
23/24, the setting range is from –1375 - 0 - 1375.
14
For adjusting the system phase of the analog
composite output and SD SDI output signals (total
SYS SC
variable range of over ±180 degrees).
(SD)
– :Phase advances.
+ :Phase delays.
0000
–108
:
:
0108
0
:
:
0216
108
36
No./Item
Description of setting
15
For adjusting the system phase of the analog
composite output signals (in 37 ns increments).
VO SYS H
– :Phase advances.
(SD)
+ :Phase delays.
0000
–858
:
:
0858
0
:
:
1716
858
<Note>
The setting range is –864 to 0 to 864 when 50i/25P,
25 (HD) or 25 (SD) is selected as the menu item
No.25 SYSTEM FREQ setting.
16
For adjusting the system phase of the SD SDI output
signals (in 37 ns increments).
SD SYS H
– :Phase advances.
(SD)
+ :Phase delays.
0000
–858
:
:
0858
0
:
:
1716
858
<Note>
The setting range is –864 to 0 to 864 when 50i/25P,
25 (HD) or 25 (SD) is selected as the menu item
No.25 SYSTEM FREQ setting.
18
For adjusting the SCH (sub-carrier to horizontal)
phase of the analog composite output signals (4
SCH
positions in 90-degree increments).
COAR
The SC phase changes, and the H phase remains
(SD)
unchanged.
0000
0
0001
90
0002
180
0003
270
19
For adjusting the SCH (sub-carrier to horizontal)
phase of the analog composite output signals
SCH FINE
(variable range of over ±45 degrees).
(SD)
The SC phase changes, and the H phase remains
unchanged.
A range of ±180 degrees is covered by using this
setting in combination with item No.18 SCH COAR
(SD).
0000
–32
:
:
0032
0
:
:
0064
32
20
For adjusting the phase of the AUDIO output signals
in relation to the video output signals (in 20.8 µs
AV
increments).
PHASE
– :Audio phase against image advance.
+ :Audio phase against image delay.
0000
–100
:
:
0100
0
:
:
0200
100
"_____" indicates the factory setting.

Advertisement

Table of Contents
loading

  Also See for Panasonic AJ-HD1400E

  Related Manuals for Panasonic AJ-HD1400E

This manual is also suitable for:

J-hd1400pAj-hd1400Aj-hd1400p