Download  Print this page

Panasonic AJ-HD1400E Operating Instructions Manual page 63

Panasonic digital hd video cassette recorder operating instructions aj-hd1400p, aj-hd1400e
Hide thumbs

Advertisement

Error messages
Error messages (continued)
Monitor display
E-55
If the tape has not been taken up during unloading, this error
number flashes on the display.
UNLOAD ERROR
E-57
If the start or end processing operation is not completed, this error
S-FF/REW
number flashes on the display.
TIMEOVER
E-59
If the cylinder motor speed is abnormally low, this error number
DRUM ROTA TOO
flashes on the display.
SLOW
E-60
If the cylinder motor speed is abnormally high, this error number
DRUM ROTA TOO
flashes on the display.
FAST
E-61
If the capstan motor speed is abnormally low, the error number
CAP ROTA TOO
flashes on the display.
SLOW
E-64
If the supply reel motor speed is abnormally high, the error number
S REEL ROTA TOO
flashes on the display.
FAST
E-67
If the take-up reel motor speed is abnormally high, the error number
T REEL ROTA TOO
flashes on the display.
FAST
E-69
If excess torque being applied to the take-up reel motor is detected,
T REEL TORQUE
the error number flashes on the display.
ERR
E-70
If excess torque being applied to the supply reel motor is detected or
S REEL TORQUE
an abnormal current flowing to the current detection resistor is
detected, this error number flashes on the display.
ERR
E-71
If abnormal tension at the supply side is detected in the capstan
CAP TENSION
mode, the error number flashes on the display.
ERROR
E-72
If abnormal tension at the supply side is detected in the reel mode,
REEL TENSION
the error number flashes on the display.
ERROR
E-73
If the take-up reel motor has rotated in the reverse direction, this
REEL DIR
error number flashes on the display.
UNMATCH
E-74
If excess torque being applied to the cylinder motor is detected, this
DRUM TORQUE
error number flashes on the display.
ERROR
If a problem has been encountered in communication between the
E-78
servo microcomputer and mechanism relay board, this error number
M-IF COMM ERROR
flashes on the display.
E-bA
This appears when the input DC voltage has dropped below the
undercut voltage.
BATTERY
<Note>
Consult your dealer if the error message display persists even after the unit has been restarted.
(continued)
Description
Corrective action
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Set the POWER switch to OFF
and then to ON again.
Check the output voltage of the
equipment supplying DC
power.
VTR
operation
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
63

Advertisement

loading

  Also See for Panasonic AJ-HD1400E

  Related Manuals for Panasonic AJ-HD1400E

This manual is also suitable for:

J-hd1400pAj-hd1400Aj-hd1400p