Dif - Panasonic AJ-YA120AG Operating Instructions Manual

Setup menus

DIF

(This menu appears only when the AJ-YAD120AG board is installed.)
Item
Superimposed
No. No.
display
880 DIF SPEED
0000
0001
0002
882 DIF IN CH 0000
0063
0064
883 DIF OUT CH 0000
0063
0064
886 DIF CONFIG 0000
0001
0255
890 DIF AUD OUT
0000
0001
891 DIF DV AUDIO
0000
0001
0002
894
HD>DIF OUT
0000
0001
0002
895
50M>DIF OUT
0000
0001
896 25M>DIF OUT
0000
0001
899 DIF SUPER
0000
0001
<Notes>
The following settings are recommended when a format other than DVCPRO HD is selected as the format of the signals to be output and an
external unit is connected to the DV connector.
O Menu item No.022 [PB FORMAT]: MANUAL
O Menu item No.023 [FORMAT SEL]: Format of the tape inserted in the unit
48
Setting
Superimposed
display
For setting the transfer speed of the digital video interface output.
S100 0: 100 Mbps
S200 1: 200 Mbps
S400 2: 400 Mbps
0 For setting the input channel.
: : 0 to 63: The input channel is fixed at the channel corresponding to the number
63 specified.
AUTO 64: The input channel is not fixed at the channel corresponding to the number
specified. The input channel is initialized to 63 when the power is turned on.
0 For setting the output channel.
: : 0 to 63: The output channel is fixed at the channel corresponding to the number
63 specified.
AUTO 64: The output channel is not fixed at the channel corresponding to the number
specified. The output channel is initialized to 63 when the power is turned on.
DFLT Menu item for expansion purposes.
1 Normally, use DFLT as the setting.
: :
255
For setting the audio channels to which the signals from the digital video interface
are to be output in the DV format when a DVCPRO HD tape or 50M format tape is
played back.
CH1/2 0: CH1 and CH2
CH3/4 1: CH3 and CH4
For setting forcible audio mode conversion when a DV tape is played back and the
audio signals are output in the DV format.
THRU 0: Normal setting (the signals simply pass through).
LOCK 1: Forcible conversion to the LOCK mode (no frequency conversion)
LOCK48 2: Forcible conversion to 48kHz/2CH/LOCK.
For setting the format of the signals to be output from the digital video interface
when a DVCPRO HD tape is played back or the E-E mode is established (while the
AJ-YA120AG board is installed).
HD 0: DVCPRO HD
50M 1: DVCPRO50
DV 2: DV
For setting the format of the signals to be output from the digital video interface
when a 50M format tape is played back.
50M 0: DVCPRO50
DV 1: DV
<Note>
When DV is selected as this item's setting, the closed caption signals and time
code (VITC) signals in the vertical blanking period are transmitted, but none of the
other signals in the vertical blanking period are transmitted.
For setting the format of the signals to be output from the digital video interface
when a 25M format tape is played back.
25M 0: DVCPRO
DV 1: DV
For setting whether the superimposed display is to be output from the digital video
interface when the format is converted (from HD to 50M, from HD to DV or from
50M to DV).
OFF 0: The superimposed text is not displayed.
ON 1: The superimposed text is displayed.
Description of settings
<Note>
When S100 has been selected as this item's setting, DVCPRO
HD format signals cannot be input or output.
" " indicates the factory setting.