Table of Contents
Advertisement
11
About the Remote Setup menu
The Remote Setup mode is set by pressing the number button while pressing RCU SETUP. The different items
on the Remote Setup menu are described below. For their setting procedures, refer to the explanations for the
respective items.
Setting
What it does
If you have multiple Pioneer receivers, amplifiers, etc., this setting can be used to prevent other units from
Change RC
operating simultaneously when the remote control unit is operated. See
mode
page 93
.
Preset codes can be set for the various input functions. The remote control codes of a number of other
Preset recall
devices (including products of other brands) are preset in the remote control to allow these devices to be
operated. See
Selecting preset codes directly
If the desired operations cannot be performed even though you have set the preset codes, the remote control
Code learning
signals of other devices can be learned directly. See
page 94
.
This function is used to erase remote control codes that have been learned. Codes learned for the different input
Erase learning
functions can be erased individually. See
This is a function for resetting preset codes that have been set. Key resetting can be done for individual input
Reset function
functions. See
Erasing all learnt settings that are in one input function
You can set to automatically switch to AV amplifier operation mode when a certain period of time elapses
Operation mode
after remote operation of each input function is finished. See
switching time
operation mode
on
page 95
.
This is a function for resetting all remote control unit settings you have made to the defaults set upon ship-
All reset
ment from the factory. See
Resetting the remote control settings
Notes
! You can cancel or exit any of the steps by pressing RCU SETUP.
! After one minute of inactivity, the remote automatically exits the operation.
Operating multiple receivers
Up to four receivers can be operated discretely using this receiver's remote control when using multiple receiv-
ers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the
preset code to set the remote control setting.
! Set the remote modes on the receivers before using this function (see
111
).
1
Press and hold RCU SETUP, then press '4' for three seconds.
Release the button after the LED flashes once. The LED continues to flash.
! To cancel the preset setup mode press RCU SETUP.
2
Press the number button for the receiver ("Receiver 1" to "Receiver 4") you wish to
operate.
For example, to operate "Receiver 2", press '2'.
If the LED lights for one second, the setting has been successfully completed.
When the preset code is input, the LED flashes three times to indicate that the setting has failed.
Operating multiple receivers
on
page 93
.
Programming signals from other remote controls
Erasing one of the remote control button settings
on
page 94
on
page 95
.
Setting the switching time for the receiver
on
page 95
.
Remote Control Mode Setup
Setting the remote to control other components
Most components can be assigned to one of the input function buttons (such as DVD or CD) using the compo-
nent's manufacturer preset code stored in the remote.
However, there are cases where only certain functions may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote control will not work for the model that you are using.
If you can't find a preset code that matches the component you want to control, you can still teach the remote
individual commands from another remote control (see
on
page 94
).
! With the TV buttons, the TV can be operated regardless of the input set for the remote control's operation
mode. When using one TV set, we recommend assigning the same TV's preset codes to the TV INPUT button
and the TV button. When using two TV sets, for better convenience assign the TV connected to the MONITOR
OUT terminals to the TV INPUT button, the other TV to the TV button.
! Devices may be assigned to the following input function buttons.
on
.
Selecting preset codes directly
1
Press and hold RCU SETUP, then press '1' for three seconds.
on
page
Release the button after the LED flashes once. The LED continues to flash.
! To cancel the preset setup mode press RCU SETUP.
2
Press the input function button for the component you want to control.
To assign the preset codes of the TV to be operated with the TV function, press the TV INPUT button.
The LED of the remote control lights.
3
Use the number buttons to enter the 4-digit preset code.
See
Preset code list
on
page 136
If the LED lights for one second and continues to flash, the setting has been successfully completed.
When the preset code is fully input, the LED flashes three times to indicate that the setting has failed. If this hap-
pens, enter the 4-digit preset code again.
4
Repeat steps 2 through 3 for the other components you want to control.
To try out the remote control, switch the component on or off (into standby) by pressing u SOURCE. If it doesn't
seem to work, select the next code from the list (if there is one).
5
Press RCU SETUP to exit the preset setup mode.
93
Controlling the rest of your system (VSX-930 only)
Programming signals from other remote controls
STANDBY/ON
SOURCE CONTROL
BD
DVD
SAT
HDMI
ALL
TV
CD
INPUT
.
on
Advertisement
Table of Contents
