Ipod; Network - Pioneer VSX-930-k Operating Instructions Manual

14

iPod

Symptom Cause
iPod is not recognized. This receiver recognizes the iPod as
a fraud.
iPod touch/iPhone is not The iPod's operation may be
recognized or otherwise unstable.
does not operate properly.
iPod cannot be operated —
with the remote control.
No audio is output when —
operating from an iPod.

Network

Symptom Cause
Cannot access the network. The LAN cable is not firmly con-
nected.
The router is not switched on.
Internet security software is cur-
rently installed in the connected
component.
The audio component on the net-
work which has been switched off is
switched on.
Fails Wireless Accessory iOS equipment is not connected to
Configuration. the Wi-Fi equipment.
Playback does not start The component is currently discon-
while "Connecting..." con- nected from this receiver or the
tinues to be displayed. power supply.
The network function can- —
not be operated with the
remote control.
The PC or Internet radio is The corresponding IP address is not
not properly operated. properly set.
The IP address is being automati-
cally configured.
Remedy
Switch off and on again this receiver.
Reconnect the iPod with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Try performing the operation below.
1. Press the sleep/sleep cancel button on the iPod touch/
iPhone simultaneously with the home button for at least 10
seconds to restart the device.
2. Turn this receiver's power on.
3. Connect the iPod touch/iPhone to this receiver.
Press iPod USB to set the remote control to the iPod USB
control mode.
Press iPod iPhone DIRECT CONTROL on the front panel,
to switch to iPod operation.
Remedy
Firmly connect the LAN cable (pages 34 , 46 ).
Switch on the router.
There are cases where a component with Internet security
software installed cannot be accessed.
Switch on the audio component on the network before
switching on this receiver.
Connect the iOS equipment to Wi-Fi.
Check whether the component is properly connected to
this receiver or the power supply.
Press NET to set the remote control to the network function
control mode.
Switch on the built-in DHCP server function of your router,
or set up the network manually according to your network
environment (page 51 ).
The automatic configuration process takes time. Please
wait.
Symptom Cause
The audio files stored on Windows Media Player 11 or
components on the net- Windows Media Player 12 is not cur-
work, such as a PC, cannot rently installed on your PC.
be played back.
The audio file currently being played
back was not recorded in a format
playable on this receiver.
The component connected to the
network is not properly operated.
The component connected to the
network does not permit file sharing.
The folder stored on the component
connected to the network has been
deleted or damaged.
Network connections could be
restricted due to the computer's net-
work settings, security settings, etc.
Supported file formats vary by server.
As such, files not supported by your
server are not displayed on this unit.
The audio files are copyrighted.
Cannot access the com- The component connected to the
ponent connected to the network is not properly set.

network.

There are no playable audio files on
the component connected to the
network.
120
FAQ
Remedy
Install Windows Media Player 11 or Windows Media Player
12 on your PC (page 75 ).
Audio files recorded in MPEG-4 AAC or FLAC cannot be
played back on Windows Media Player 11 or Windows
Media Player 12. Try using another server. Refer to the
operation manual supplied with your server.
Check whether the component is affected by special cir-
cumstances or is in the sleep mode.
Try rebooting the component if necessary.
Try changing the settings for the component connected to
the network.
Check the folder stored on the component connected to
the network.
Check the computer's network settings, security settings, etc.
For more information check with the manufacturer of your
server.
DRM-protected audio files cannot be played back on this
receiver.
If the client is automatically authorized, you need to enter
the corresponding information again. Check whether the
connection status is set to "Do not authorize".
Check the audio files stored on the component connected
to the network.