Table of Contents
Advertisement
13
MHL Setup
Select whether or not to switch the input automatically to the MHL input when an MHL-compatible device is
connected.
! Default setting: ON
1
Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and
then press HOME MENU.
A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.
! Press HOME MENU at any time to exit the HOME MENU.
2
Select 'System Setup' from the HOME MENU, then press ENTER.
3
Select 'MHL Setup' from the System Setup menu.
4
Select the 'Auto input switching' from the MHL Setup menu.
Use k/l to select the setting.
5
! OFF – Does not automaticly switch to MHL input.
! ON – Automatically switches to MHL input.
6
Select 'OK', then press ENTER.
Notes
! This is only valid for MHL-compatible devices supporting this function.
! When the power is on, the MHL-compatible device is charged. (This receiver supports charging of devices up
to 0.9 A.)
The Other Setup menu
The Other Setup menu is where you can make customized settings to reflect how you are using the receiver.
1
Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and
then press HOME MENU.
A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.
2
Select 'System Setup' from the HOME MENU.
3
Select 'Other Setup', then press ENTER.
4
Select the setting you want to adjust.
If you are doing this for the first time, you may want to adjust these settings in order:
! Auto Power Down – Sets the power to turn off automatically when the receiver is not being used
! Volume Setup – Sets up the volume-related operations of this receiver
! Software Update – Use to update the receiver's software and check the version
! On Screen Display Setup (VSX-930 only) – Sets whether or not to display the status on the display when the
receiver is operated
(page 110
).
! Remote Control Mode Setup (VSX-930 only) – Sets this receiver's remote control mode
! ZONE Setup (VSX-930 only) – Use to make the sub zone-related settings
5
Make the adjustments necessary for each setting, pressing RETURN to confirm after each
screen.
Auto Power Down
The power can be set to turn off automatically if no operation has been performed for a specific amount of time
with no audio or video signals being input to the receiver.
VSX-930 only: When using HDZONE, the HDZONE power can also be set to turn off, but for HDZONE the power
turns off automatically after the amount of time set here even if signals are being input or operations have been
performed. Different times can be set for the main zone and HDZONE.
1
Select 'Auto Power Down' from the Other Setup menu.
2
Select the zone you want to set and set the time after which the power turns off.
! MAIN – The time can be selected from among "15 min", "30 min", "60 min" and "OFF". The power turns off
after there has been no signal and no operation for the selected time.
! HDZONE (VSX-930 only) – The time can be selected from among "30 min", "1 hour", "3 hours", "6 hours",
"9 hours" and "OFF". The power turns off after the selected time.
Notes
! Depending on the connected devices, the Auto Power Down function may not work properly due to excessive
noise or other reasons.
! When using WAC mode
Volume Setup
You can set the maximum volume of this receiver or specify what the volume level will be when the power is
turned on.
1
Select 'Volume Setup' from the Other Setup menu.
2
Select the Power ON Level setting you want.
The volume can be set so that it is always set to the same level when the receiver's power is turned on.
! LAST (default) – When the power is turned on, the volume is set to the same level as when the power was last
turned off.
! "---" – When the power is turned on, the volume is set to minimum level.
! –80.0dB to +12.0dB – Specify the volume to be set when the power is turned on, in steps of 0.5 dB.
It is not possible to set a volume level greater than the value specified at Volume Limit setup (see below).
3
Select the Volume Limit setting you want.
Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by
operating VOLUME button (or the dial on the front panel).
! OFF (default) – The maximum volume is not limited.
! –20.0dB/–15.0dB/–10.0dB/–5.0dB/0.0dB – The maximum volume is limited to the value set here.
4
Select the Mute Level setting you want.
(page 109
).
This sets how much the volume is to be turned down when MUTE is pressed.
(page 109
).
! FULL (default) – No sound.
(page 110
).
! –40.0dB/–20.0dB – The volume will be turned down to the level specified here.
5
When you're finished, press RETURN.
You will return to the Other Setup menu.
(page 111
).
(page 111
).
109
The System Setup and Other Setup menus
(page 53
), this feature does not work.
Advertisement
Table of Contents
