Piping Specifications - SMC Networks ZSE30 Series Manual

2-color Display Digital Pressure Switch

Piping Specifications

Part
Port
One-touch fitting
Straight type
size
One-touch fitting
Elbow type
Wetted part material
With lead wire
with connector (2 m)
Weight
Without lead wire
with connector
High Precision,
Specifications
Rated pressure range
Regulating pressure range
Proof pressure
Min. regulating unit
Fluid
Power supply voltage
Current consumption
Note 1)
Switch output
Max. load current
Max. applied voltage
Residual voltage
Response time
Short circuit protection
Repeatability
Voltage output
Analog
output
Current output
Hysteresis mode
Hysteresis
Window comparator mode
Display
Display accuracy
Indicator light
Temperature characteristics
Enclosure
Operating temperature range
Operating humidity range
Withstand voltage
Insulation resistance
Vibration resistance
Impact resistance
Standard
Note 1) When switch output is selected, analog output is not available.
Note 2) When voltage output is selected, a simultaneous selection of switch output and current output is
not available.
Note 3) When current output is selected, a simultaneous selection of switch output and voltage output is
not available.
01 T1 C4H
R 1/8 NPT 1/8
M5 x 0.8 M5 x 0.8
ø4 mm
— —
ø5/32 inch
— —
Sensor pressure receiving area: Silicon, Piping port: C3602 (Electroless nickel plated), O-ring: HNBR
81 g
43 g
Series
ZSE30 (Vacuum/Low pressure)
–100.0 to 100.0 kPa
–101.0 to 101.0 kPa
500 kPa
0.2 kPa
Air, Inert gas, Non-flammable gas
12 to 24 VDC, Ripple (p-p) 10% or less (With power supply polarity protection)
NPN or PNP open collector output: 1 output
1 V or less (With load current of 80 mA)
2.5 ms or less (Response time selections with anti-chattering function: 20, 160, 640, 1280 ms)
±0.2% F.S. ±2 digit or less
Note 2)
Output voltage: 1 to 5 V ±2.5% F.S. or less (With rated pressure range)
Linearity: ±1% F.S. or less, Output impedance: Approx. 1 kΩ
Output current: 4 to 20 mA ±2.5% F.S. or less (With rated pressure range)
Note 3)
Maximum load impedance: 300 Ω with power supply voltage of 12 V;
Minimum load impedance: 50 Ω
Adjustable (can be set from 0)
3 1/2 digit, 7-segment indicator, 2-color display (Red and green)
±2% F.S. ±2 digit
(at 25°C ambient temperature)
Light up when output is ON (Green)
±2% F.S. or less (based on 25°C)
Operating: 0 to 50°C, Stored: –10 to 60°C (No freezing or condensation)
Operating and stored: 35 to 85% RH (No condensation)
1000 VAC for 1 min. between live parts and enclosure
50 MΩ or more between live parts and enclosure (at 500 VDC)
10 to 150 Hz, 1.5 mm or 20 m/s
100 m/s
Compliant with CE Marking and UL (CSA) standards
C6H N7H
— — —
ø6 mm ø1/4 inch
—
— —
O-ring: NBR
76 g
38 g
ZSE30/ISE30
ISE30 (Positive pressure)
0.000 to 1.000 MPa
–0.100 to 1.000 MPa
1.5 MPa
0.001 MPa
45 mA or less (at no load)
80 mA
30 V (With NPN output)
Yes
±0.2% F.S. ±1 digit or less
Linearity: ±1% F.S. or less
600 Ω with power supply voltage of 24 V
Sampling cycle: 5 times/s
±2% F.S. ±1 digit
(at 25°C ambient temperature)
IP40
2
amplitude in X, Y, Z directions for 2 hours each
2
in X, Y, Z directions 3 times each
C4L C6L
— —
— —
ø4 mm
ø6 mm
ø5/32 inch
O-ring: NBR, fitting: PBT
78 g
40 g
ZSE„
ISE„
PSE
Z
SE3
I
PS
Z 1
SE
I 2
ZSP
ISA2
IS„
ZSM
PF2„
IF„
Data
N7L
—
—
ø1/4 inch
16-2-5