SMC Networks ZSE30 Series Manual page 8

ZSE30/ISE30
Series
Setting
Function setting
Display calibration
During measuring mode, press the SET and
simultaneously and hold for 2 seconds or longer.
current measured value will be displayed.
Press the UP or DOWN button to change the set value. If
there is no button operation for more than 2 seconds after
changing the set value, the display mode returns to displaying
and the current measured value.
PRESSURE
OUT
Press the SET button to display the adjusted value (percent).
The adjusted value and
PRESSURE
OUT
Press the SET button to return to the normal measuring mode.
OUT
This function eliminates slight differences in the output values and
allows uniformity in the numbers displayed.
Displayed values of the pressure sensor can be calibrated to within
±5% for Series ISE and ±2.5% for Series ZSE.
±5% R.D.
(±2.5% R.D.)
0 Applied pressure
Note) When the display calibration function is used, the regulating pressure
value may change ±1 digit.
Peak/Bottom hold function
This function constantly detects and updates the maximum
and minimum pressure values and allows to hold the display
value.
To use a peak hold function, press and hold the
for 1 second or longer. The maximum pressure value is held
and blinks repeatedly. Press and hold the
for 1 second or longer to release this function and return to
the measuring mode.
To use a bottom hold function, press the
second or longer. The minimum pressure value is held and
blinks repeatedly. Press and hold
second or longer to release this function and return to the
measuring mode.
16-2-8
DOWN buttons
PRESSURE
Alternately
displayed
OUT
Current measured value
will be alternately displayed.
PRESSURE
Alternately
displayed
OUT
Adjusted value
(Percent)
PRESSURE
+
: Factory setting display value
set prior to shipment
: Display calibration range
UP button
UP button again
DOWN button for 1
DOWN button again for 1
Key lock function
This function prevents incorrect operations such as changing
and the set value accidentally. Press the SET button and hold for 4
seconds or longer to display the current
Press the UP or
this function with the SET button. Use the
accidental button operation. To release a key lock function,
press the SET button and hold for 4 seconds or longer to
display the current setting, and select the
SET
Press the
and hold for 4 sec.
or longer
Zero out (Zero ADJ) function
This function clears and resets the displayed value as long as
the measuring pressure is within ±70 digits of the atmospheric
pressure.
(Due to individual product differences, the setting range varies
±10% F.S.)
This function is effective in detecting pressure fluctuations that
exceed a certain amount without being affected by the supply
pressure. Press and hold the
simultaneously to reset the display. Release the buttons to
return to the measuring mode.
+
Press and hold for
1 second or longer.
Unit Conversion Function
When not selecting "M" for unit specification
Desired display unit can be selected.
Press the UP or
the set value is automatically converted.
The conversion order is: PA⇔GF⇔bAr⇔PSi⇔inH⇔mmH
Press the SET button to set the unit and proceed to the
display color setting.
For vacuum/low pressure
For positive pressure
Indication of Units
Displayed unit
Pa
2
kgf/cm
bar
psi
mmHg
inchHg
DOWN button to select the setting and set
Selection of lock and unlock
button
Lock Unlock
UP and
DOWN button to switch the unit, and
⇔bar⇔psi⇔inchHg⇔mmHg
2
Pa⇔kgf/cm
⇔bar⇔psi
2
MPa⇔kgf/cm
ISE30
0.001 MPa
0.01
0.01
0.2
—
—
or setting.
mode to avoid
mode.
SET
DOWN buttons
ZSE30
0.2 kPa
0.002
0.002
0.05
2
0.2