Icom IC-7000 Instruction Manual page 23

!1 SPLIT INDICATOR
(pp. 89, 90)
Appears during split operation.
!2 IF FILTER
INDICATOR (p. 75)
Shows the selected IF filter number.
!3 PASSBAND WIDTH
INDICATOR (p. 75, 77)
Graphically displays the passband width for twin
PBT operation and center frequency for IF shift
operation.
!4 MODE INDICATORS
(p. 34)
Shows the selected operating mode.
is selected.
!5 PROGRAMMABLE/1 MHz TUNING STEP
INDICATORS
!5
a appears when the 1 MHz quick tuning step
is selected. (p. 31)
!5
b appears when the programmable tuning step
is selected. (p. 30)
!6 FUNCTION INDICATORS
" " appears when the VOX function is
activated. (p. 83)
" " appears when full break-in operation is
selected and "
break-in operation is selected.
" " appears when the speech compressor is
activated. (p. 87)
" ," " ," "
appears when the fast, middle, slow time
constant or AGC OFF is selected.
" " appears when the VSC (Voice Squelch
Control) function is activated in phone (SSB,
AM, FM, WFM) modes.
" " appears for negative offset and "
appears for positive offset during duplex
operation. (p. 63)
" " appears when the 9600 baud mode is
activated for packet operation.
" " appears when the preamp is ON,
" " appears when the 12 dB attenuator is
ON. (p. 72)
appears when the RIT or ∂TX
" " or " "
function is activated.
" " a p p e a r s w h e n t h e n o i s e bl a n ke r i s
activated. (p. 78)
" " appears when DSP noise reduction is
activated. (p. 79)
" " appears when the manual notch function
is activated. (p. 81)
" " a p p e a r s w h e n t h e a u t o m a t i c n o t c h
function is activated.
" appears when semi
(p. 85)
" or " " (OFF)
(p. 74)
(p. 82)
(p. 116)
(pp. 73, 86)
(p. 80)
!7 MULTI-FUNCTION SCREEN
Shows the screens for the multi-function meter,
simple band scope, SWR meter, memory channel,
voice recorder, memory keyer, DTMF memory
encoder, RTTY decoder, IF filter selection or popup
indication, etc.
!8 PRIORITY WATCH INDICATOR
Appears while priority scan is activated.
!9 SELECT MEMORY CHANNEL INDICATOR
(p. 113)
Appears when select scan is enabled for the
selected memory channel.
@0
1/4 FUNCTION
Appears when the
activated in CW and RTTY modes.
@1 EXTERNAL KEYPAD INDICATOR
Shows the memory keyer or voice memory channel
number. This indication appears when "External
Keypad (VOICE)" or "External Keypad
(KEYER)" in the miscellaneous (others) Set mode
(p. 135) is set to ON, and which one is activated.
" " appears when the memor y keyer "M2" is
transmitted.
" " appears when the voice memor y "T1" is
transmitted.
@2 CLOCK READOUT
Shows the current time.
@3
TONE INDICATOR
Appears during FM tone operation.
" ," " " or "
"
tone, tone squelch, DTCS squelch are activated,
respectively.
@4
TUNER INDICATOR
Appears when the optional automatic antenna
tuner is activated.
PANEL DESCRIPTION
(p. 113)
INDICATOR (p. 32)
1
⁄ -speed tuning function is
4
(p. 117)
(pp. 60, 61, 64)
" appears when the repeater
(pp. 114, 115)
1
1
14