OBJ_BUCH-2364-001.book Page 8 Wednesday, February 18, 2015 11:06 AM
8 | English
Planer Safety Rules
Wait for the cutter to stop before setting the tool down.
An exposed rotating cutter may engage the surface leading
to possible loss of control and serious injury.
Hold the power tool by insulated gripping surfaces on-
ly, because the cutter may contact its own cord. Cutting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the
work by your hand or against the body leaves it unstable
and may lead to loss of control.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Do not reach into the chip ejector with your hands. They
could be injured by rotating parts.
Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
When working, always hold the planer in such a manner
that the planer base plate faces flat on the workpiece.
Otherwise the planer can become wedged and lead to inju-
Never plane over metal objects, nails or screws. The
planer blade and the blade shaft can become damaged and
lead to increased vibrations.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
The machine is intended for planing of firmly supported
wooden materials, such as beams and boards. It is also suita-
ble for beveling edges and rebating.
1 609 92A 10C | (18.2.15)
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Planing depth scale
2 Depth adjustment knob (insulated gripping surface)
3 Chip ejector
4 Lock-on button for On/Off switch
5 On/Off switch
6 Screw for belt cover
7 Belt cover
8 Planer base plate
10 Torx key
11 Fastening screw for clamping jaw
12 Clamping jaw
13 Blade drum
14 Guide groove for planer blade
15 HSS planer blade
16 HSS planer-blade retainer
17 Fastening screw for HSS planer-blade retainer
18 Sharpening device for HSS planer blade
19 Setting gauge for HSS planer blade
20 Carbide blade (TC)*
21 Parallel guide
22 Scale for rebating width
23 Locking nut for adjustment of rebating width
24 Fastening bolt for parallel and beveling guide
25 Angle stop*
26 Locking nut for angle adjustment*
27 Fastening bolt for rebating depth stop*
28 Rebating depth stop*
29 Park rest
30 Drive belt
31 Large pulley
32 Small pulley
33 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Rated power input
Planing width, max.
Weight according to
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
0 601 596 0..
0 – 2.6
0 – 9
Bosch Power Tools