Table of Contents
Advertisement
BASIC COPYING FEATURES
SETTING AN ORIGINAL ON THE UNIT
There are two ways to place originals on the unit for
copying. The method you choose depends on the size
and type of original you want to copy, and the copy
settings you have selected.
I
Platen glass
Use the platen glass when copying books, originals
on heavy or lightweight paper, and transparencies.
I
Automatic Document Feeder (ADF)
When you have a stack of originals on paper
suitable for automatic feeding, (Appendix B) use
the Automatic Document Feeder (ADF).
COPYING AN ORIGINAL SET ON THE PLATEN
GLASS
NOTE:
•
A4-size originals can be placed vertically or
horizontally. Place the originals within the marked
sizes on the platen glass.
•
A3 originals must be placed horizontally on the
platen glass.
Follow the steps below to use the platen glass when
copying books, originals on heavy or lightweight paper,
transparencies, and any other media that cannot be
fed through the Automatic Document Feeder (ADF).
1. Press COPY to switch to copy mode.
2. Lift up the platen cover.
3. Set the original, face down, vertically or horizontally
on the platen glass.
4. Align the top edge of your original with the arrow
mark on the top left corner of the platen glass.
❏ Place the original on the platen glass vertically
or horizontally, depending on the size of the
original.
A4 FAX
A5
A4
A3
A4
ORIGINAL
(FACE DOWN)
A5
A4
A4 FAX
A4
A3
VERTICAL POSITION
A5
, A4
A4 FAX
A5
A4
A3
A4
ORIGINAL
(FACE DOWN)
A5
A4
A4 FAX
A4
A3
HORIZONTAL POSITION
A5
, A4
, A3
❏ When enlarging or reducing an original, select
the paper size in accordance with the degree
of enlargement or reduction. The direction to
set the original also depends on the direction
the paper is set in. Determine the direction in
which to place the original by the markings on
the near edge of the platen glass. See "Direction
of the Original According to its Size and
Magnification Ratio" when setting the original.
NOTE:
•
Make sure that the paper in the paper cassette is
loaded in the same direction as the original is
placed on the platen glass.
•
To make a same-size copy of an A4(
set the original to A4
. Setting A4
the copy speed.
•
To make a same-size copy of an A5(
be sure to set A5
paper in the stack bypass.
5. Gently lower the platen cover.
❏ Do not press down forcefully on the platen cover
when using the platen glass to copy thick books.
This may damage the platen glass. The
maximum load is 2 kg.
6. Press F2 (PAPER SELECT) to select the paper size.
❏ The selection changes every time you press F2.
READY TO COPY
TEXT
100%
1
A4
COPY RATIO
COPY RATIO PAPER SELECT
PAPER SELECT
SCAN MODE
SCAN MODE
❏ If you have installed one of the optional paper
cassettes, the display sequence is as follows:
– paper size loaded in upper cassette, — paper
size
loaded
in
Stack bypass.
❏ Make sure the paper in the paper cassette is
loaded in the same direction as the original is
placed on the platen glass.
7. Press Set.
❏ If you do not press Set within three seconds of
selecting the paper size above, the paper you
selected will be automatically set without you
having to press Set.
❏ If you have installed the optional paper cassette,
you should load the paper size you use most
frequently in the upper cassette.
❏ You can also make a reduced or enlarged copy
of your original.
❏ You can also select one of the special copying
features except 2 on 1 combination. (Chapter 5)
BASIC COPYING FEATURES
) original,
slightly slows
) original,
21/08 '99
SAT 15:30
1
lower
cassette,
4 - 1
Advertisement
Table of Contents
