Table of Contents
Advertisement
SP-6 PITCH CONTROLS
There
are
i n d i v i d u a l
Pitch Slider,
Bend, Nudge, and Keylock controls for each
sample slot. The BPM is also displayed next to
the pitch slider. If no BPM is present in the tracks
ID3 tag, the pitch of the track is displayed as a
percentage.
Click and drag the pitch slider to make regular
pitch adjustments. Hold the shift key and move
the pitch slider to make fine pitch adjustments.
Click on the + and – buttons to nudge the
track into time. (temporary pitch adjustment)
Hold the ctrl key and click the + and – buttons to
make ultra-fine pitch adjustments to nudge the
track, adjusting the pitch permanently.
SP-6 'PLAy FROM' SELECTOR
Use
the
"Play From"
selector to choose where the track will play from.
You can choose to play a track from the start of
the file, any one of the cue points, or any one of
the loop in points.
When this is set to play from start, or play from
a cue point, the track will play right through until
stopped. When a loop is selected, the track will
play until the loop out point, unless you have
"repeat" on, in which case the track will loop
using the in and out points of the selected loop.
The number of options will be dependent on
the number of cue points and loops already set
in your track. i.e if the track loaded has no cue
points and loops set, then only "start" will be
available as a "Play From" option.
TIP: To set or adjust cue and loop information
for a track, load it to a Virtual Deck, make
your adjustments, then load it back into the
sample slot.
SP-6 TRACk OVERVIEWS
Displays
an
overview of the
track loaded to each sample slot. The waveform,
play head position, cue points and selected
loops will all be visible.
26
SP-6 SLOT VOLUMES
Each
individual
sample slot
has a separate volume slider and gain control.
Volume Sliders - Use the volume slider to mix
and make temporary adjustments to the volume
of the sample you are playing. These sliders act
like your mixer's, fading from full volume right
through to completely silent.
Gain knobs - In addition to the volume slider
there is an additional gain knob for each slot.
These allow you to fine tune the maximum
gain volume of the loaded sample. The gain
adjustment will also be written to the track's ID3
tag, meaning that it will be the same everytime
you load it.
SP-6 OUTPUT SELECTOR
Use the master output selector
button to choose where you
wish to have the SP-6 output
to.
L to PGM 1 with
1 or
the PGM Source.
A to
AUx.
R to PGM 2 with
1 or
the PGM Source.
There is also a master sample player
Gain knob to adjust the overall SP-6
volume.
INDIVIDUAL OUTPUT SELECTORS
By
default
each sample
slot will be set to Master, mirroring the SP-6
master output setting. You can however, use the
individual output selector buttons to override the
Master output setting.
To send an individual slot to a different output
from the Master, deselect the master option
by clicking on the MASTER button for the
corresponding slot.
This will unlink the sample slot from the
master sample player output selection, allowing
you to choose the L, A, or R output for each slot.
These output routings will be saved when you
close down Scratch Live, so the next time you
launch Scratch Live, your preferred settings will
remain the same.
SP-6 SAMPLE BANkS
The SP-6 has four separate
sample banks, labeled A, B, C
and D. To switch between the
different banks click on the A, B, C or D buttons.
Each bank will save the individual sample and
sample slot settings you last used, allowing you
to prepare banks for easy recall at a later stage.
Sample Bank A will load as the default.
SP-6 MUTE BUTTONS
Use the mute buttons to mute the audio
output for each of the SP-6's sample
slots. Click the mute button to silence the audio
output, click the mute button again to turn the
audio back on.
You can also ctrl-click on the mute buttons to
mute the outputs momentarily, meaning that the
2 selected as
audio will only be muted for as long as you hold
your mouse click.
TIP: you can MIDI assign these buttons,
2 selected as
allowing you to create a virtual kill switch for
the sample slot. To MIDI assign momentary
mute, hold ctrl and click on the mute button
before tapping your MIDI controller.
SP-6 MIDI
All features of the SP-6 are MIDI assignable.
The SP-6 window must be opened first before
enabling MIDI assign mode.
ON PAGE 28.
RANE SIXTY-ONE
FOR
SERATO SCRATCH LIVE
SEE "MIDI CONTROL"
•
OPERATOR'S MANUAL
2.4
Advertisement
Table of Contents
Troubleshooting
