Table of Contents
Advertisement
There are 9 available loop slots per track.
If a loop is set in a given slot, the background
(behind the loop number) will be green. Press
the x button to clear the loop. If you click on the
locked loop symbol, a red border will appear.
This indicates the loop is locked, and you will
not be able to adjust the end points or delete
the loop until you unlock it, by clicking on the
number again.
NOTE: Looping applies to REL and INT
modes.
AUTO-LOOPING
A u t o - l o o p i n g
allows you to
create
loops
instantly. If the
track has a BPM value simply click the number
of beats you wish to loop and Scratch Live will
create the loop for you. The loop is snapped to
the beats in the song detected by Scratch Live
so even if you press the button slightly out of
time Scratch Live will still create a perfect loop
for you.
Five auto-loop buttons are available on screen
at any one time. They range from 1/32 to 32
beats. The user can select the auto-loop range
with the and buttons.
Pressing an auto-loop button will create a loop
start point from the nearest beat to the playhead
(within reason), and set a loop endpoint in the
future. Pressing auto-loop 1 while auto-loop
1 is active will deactivate the loop. Pressing a
different auto-loop button while looping is active
will extend the endpoint of the current loop to
the appropriate new auto-loop length.
You can also save an auto-loop to the next
available slot. When using an auto-loop, a
save button is visible where the lock loop button
normally is.
NOTE: Auto-looping requires the track BPM
to be set.
SEE "SET AUTO BPM" ON PAGE 16.
24
THE A-SLOT
A special loop slot 'A' exists for auto-looping. The
act of using the auto-loop buttons sets a loop in
the 'A' slot, following the rules above. Turning
a loop off using the auto-loop buttons returns
you to the loop slot that you were previously in
at the time you started auto-looping. Turning
the loop off using the LOOP button leaves you
in the 'A' slot. The 'A' slot is not saved to disk
automatically, pressing 'save' saves the loop to
the first empty slot in 1-9.
Auto-looping shortcut keys are alt-1 to 5 for
the Left Deck, and alt-6 to 0 for the Right Deck.
They correspond to the looping buttons as laid
out on screen. ie. if the onscreen buttons display
1 2 4 8 16 beat loops, alt-1 triggers a 1 beat loop,
and alt-5 triggers a 16 beat loop.
LOOP ROLL
Loop roll performs a standard auto-loop, but
when the loop is turned off, the playback position
is returned to the position where it would be if it
had not entered the loop (much like censor).
The other difference between loop roll
and standard auto-loop is the ''roll'' button is
momentary. The loop is engaged when the
button is pressed down, and disengaged when
the button is released. Use short loop lengths to
create "stutter" type effects.
To activate loop roll, hold control + alt while
clicking on the desired autoloop increment, or
use the keyboard shortcuts: control + alt + 1
through 5 for the Left Deck and control + alt + 6
through 0 for the Right Deck. (ie. the same as the
auto-loop controls with the additional 'alt' key as
a modifier).
The range of values available for loop roll are
1/32 through to 32 beats. The shortcut keys
will activate whichever loop lengths are visible
on screen, i.e., if you have lengths of a 1/4 beat
through to 4 beats visible for the Left Deck,
control + alt + 1 will activate a 1/4 beat loop roll,
control + alt + 2 will activate a 1/8 beat loop roll
and so on.
Use the and buttons to toggle through
the range of possible lengths visible onscreen.
LOOP ROLL WITH MIDI
You can assign loop roll to MIDI in several ways:
After pressing the MIDI assign button in Scratch
Live, press the control + alt keys, click on an
auto-loop value, then click on the button/slider
you want it mapped to on your MIDI controller.
Alternatively, you can assign the singular loop
roll button to MIDI, then assign a MIDI knob or
slider on your controller to the autoloop select
knob (visible in the MIDI assign panel area when
in MIDI assign mode) to change the values on
the fly.
TIP: When you have the "Autoloop Select"
knob assigned to MIDI, you have all of the
loop roll lengths at your disposal. This allows
you to roll up and down the loop length scale,
to create interesting stutter and build-up
effects.
NOTE: Like auto-loop, loop roll requires a
BPM value written to the ID3 tag in order
to work. Build overviews with the "Set Auto
BPM" box checked and the proper range for
your music selected to ensure an accurate
BPM value.
TO USE THE LOOP CONTROLS ON THE SIXTy-
ONE, SEE "FLEXFX" ON PAGE 10.
RANE SIXTY-ONE
FOR
SERATO SCRATCH LIVE
SEE "SET AUTO BPM" ON PAGE 16
•
OPERATOR'S MANUAL
2.4
Advertisement
Table of Contents
Troubleshooting
