Spécifications Techniques - Fantom F1420CD Owner's Manual

OPERATING INSTRUCTIONS
18. Check to make sure that the belt is
centered on the pulley and that the
agitator turns.
19. Replace the top cover over the power
head base and replace the screws,
first the ones on the back of the power
head and then the ones on the bottom
and screw firmly.
Changing the Headlight Bulb
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter, changing the filters or
performing maintenance/trouble shooting
checks.
1. Turn unit "Off" and unplug from wall
outlet.
2. With a flathead screw driver, insert into
one of the two slots on top of the head
light lens and gently pull down. (Fig. 41)
3. Lift out the head light lens.
Lens Slots
Fig. 41
4. Remove the light bulb by pulling it
out carefully.
5. Replace the new bulb by pushing
it in.
6. To replace the head light lens insert
bottom tabs of lens into holding slots
and snap top back into place to
secure.
Storage
The vacuum handle has a unique
handle that folds for easy storage and
easier portability for use with hose.
1. To fold handle, turn the folding
handle release below the handle.
(Fig. 42)
2. Push the handle down until it is in
the storage position.
3. To return the handle to the upright
position, pull handle upwards to the
upright position until you
hear the
handle lock
into place.
NOTE
: The
folding handle
release is on a
spring and
will return to
its original
position.
Motor Thermostat
Important:
This unit is equipped with a
motor protective thermostat. If for some
reason the vacuum cleaner should
overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the power
source.
• Check the source of overheating
problem. (i.e. clogged hose or filter)
• If clogged hose or filter is found, unclog
the hose and replace the filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for 45
minutes, plug in the cleaner and push
the On/Off button. The vacuum should
start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 275-9251.
12
FAMILIARISATION AVEC VOTRE ASPIRATEUR VERTICAL
Handle
release
Fig. 42
1. Poignée pliante
2. Déclencheur de la poignée pliante
3. Boyau flexible
4. Sélecteur tapis-plancher
5. Déclencheur de la poignée
6. Couvercle du filtre d'échappement.
7. Surveille-filtre Intelli-Sense
8. Support du cordon d'alimentation
avec dispositif de relâche rapide
9. Cordon d'alimentation
10. Bouton de relâche de la portière de
retenue
11. Poignée du boyau
12. Tube télescopique
13. Commutateur Arrêt/silencieux/
normal (Off/Quiet/Normal)
Spécifications techniques
Tension:
Demande:
Remarque: Les illustrations peuvent différer de l'unité actuelle.
14. Brosse turbo actionnée à l'air
15. Poignée de transport
16. Poignée de la coupelle à
poussière
17. Couvercle de la coupelle à
poussière
MC
18. Coupelle à poussière
19. Brosse à épousseter
20. Brosse pour divans
21. Suceur plat
22. Lampe de tête au xénon
23. Régleur de la hauteur du
tapis
24. Connecteur du boyau
25. Chariot pour outil
26. Plumeau autonettoyant
120V, 60Hz.
12 Ampères
33