Dig. Comunicat - Bentel Security KYO 320 Installation Manual

10d. Using A or B, select the Dial, Timeout or Voice
on line option, then press ENTER. Refer to the respec-
tive paragraph for instructions.
Timeout
The Dialler Message will be played when the program-
med Timeout length (refer to Delay) expires.
Timeout length
Sec. 005
11d. Enter the Timeout length (from 1 to 255 se-
conds), then press ENTER to go back to step 4b, or
press ESC to go back to step 10d.
Voice on line
The Dialler message will be played as soon as the Con-
trol panel detects a voice answer. If the Control panel
does not detect a voice answer within the programmed
Wait voice for time (refer to Voice timeout), it will end
the call.
Wait voice for
Sec. 015
11e.Enter the Wait voice for (from 1 to 255 seconds),
then press ENTER to go back to step 4b, or press ESC
to go back to step 10d.
Dialling
The Dialler message will be played as soon as the Con-
trol panel finishes dialling the telephone number. Go
back to step 4b.
n Dig. comunicat.

Dig. Comunicat.

Dig.com.numbers
4c. Using A or B, select the Dig.com. numbers,
Dig.com. actions or Dig.com. settings option, then
press ENTER. Refer to the respective paragraph for in-
struction. Press ESC to go back to step 3.
Dig. com.numbers
Dig.com.numbers
Number 01
5g. Enter the ID number of the Digital Communicator
Number to be programmed, then press ENTER to conti-
nue. Press ESC to go back to step 4c.
Tel.numb. n.001
Phone number 001
6g. Using A or B, select the Telephone Number (from
the Phonebook) to be associated with the selected Digi-
tal Communicator Number, then press ENTER.
34
Protocol
ADEMCO SLOW
7g. Using A or B, select the Protocol supported by the
Central Station the Digital Communicator call will be
sent to, then press ENTER.
System code
Code 0000
8g. Enter the System code (three to six digits as requi-
red by the reporting format). The System Code (assi-
gned by the Central Station) allows the operator to
identify the system. Press ENTER.
Send always
System Code x
9g. Press ON or OFF, respectively, to enable or disable
the Send always option. If this option is enabled, the
Control panel will always send the System Code. If this
option is disabled, the Control panel will send the parti-
tion code (refer to "Customer Code" under "Partitions")
for partition related events and the System Code for all
other events. Press ENTER to go back to step 5g.
Dig.com. actions
Each Digital Communicator action can manage one
Event code which can be sent to a group of up to eight
Telephone numbers.
Dig.com.actions
Action n. 001
5h. Enter the ID number of the Digital Communicator
action to be programmed then, using A or B, select the
Event code A or B. Press ENTER to continue or ESC to
go back to step 4c.
Tel. Number
x
6h. Using keys 1 through 8, setup the Digital Communi-
cator Tel. numbers that will be called when the selected
action is generated ("û" means the Tel. number will be
called). Press ENTER to go to the next step.
Action options
Priorit. tel.
7h. Press ON or OFF, respectively, to enable or disable
the Priorit. tel. option (refer to "!"). Press B to go to the
next option.
Action options
Call anyone
8h. Press ON or OFF, respectively, to enable or disable
the Call anyone option (refer to "All"). Press A to go to
the previous option (refer to step 7h) or press ENTER.
1-8
KYO320