Table of Contents
Advertisement
Available languages
Available languages
Grasp the cranking handle (19) and slowly pull the
cranking rope until a resistance is felt. Then, pull
quickly and firmly.
Do not fully pull out the cranking rope and slowly
guide the cranking handle back to make sure
that the cranking rope is correctly wound up..
Put the choke lever (20) to the position
engine has started.
The engine will idle when you release the throttle
trigger.
S
t
o
p
p
i
S
t
o
p
p
Release the throttle trigger (14)
Put the ON/OFF switch (15) to its bottom position
S
t
a
r
t
i
n
g
w
S
t
a
r
t
i
n
g
w
Start the device as described under "Starting with cold engine",
but leave the choke lever in its operating position
W
o
r
k
i
n
W
o
r
k
i
n
You may not start to operate the machine until you
have read these original instructions, observed all the in-
structions given and completely and properly assembled
the machine!
Always apply the carrying strap (12) when working
with this machine.
Adjust the carrying strap so that a convenient and safe carrying
of the machine is ensured.
Always keep your hands and feet at a safe distance to
the cutting tool.
W
o
r
k
i
n
g
w
i
t
W
o
r
k
i
n
g
w
i
t
Trimming
• Incline the machine slightly forward and uniformly move it
from left to right with adequate speed.
• You will get the best trimming results when you cut dry grass.
•
Do not guide the cutting thread directly at walls and
paving stones. Otherwise it will prematurely wear off.
• Cut higher grass and denser growth in several passes to
prevent the spool head from becoming blocked.
A blocked spool head may cause coupling damage.
• The cutting thread is after-running once the lawn trimmer has
been cut off. Therefore wait until the thread is stationary be-
fore you restart the product.
20
n
g
t
h
e
e
n
g
i
n
e
i
n
g
t
h
e
e
n
g
i
n
e
i
t
h
w
a
r
m
e
n
g
i
n
e
i
t
h
w
a
r
m
e
n
g
i
n
e
.
g
i
n
s
t
r
u
c
t
i
o
n
s
g
i
n
s
t
r
u
c
t
i
o
n
s
h
t
h
e
g
r
a
s
s
t
r
i
m
m
e
r
h
t
h
e
g
r
a
s
s
t
r
i
m
m
e
r
Thread follow-up
During trimming, the cutting thread wears (becomes shorter) or
it may tear off so that it can no longer cut grass.
Shortly press the machine against solid ground. This will extend
the cutting thread (by approx. 4 cm). If the cutting thread ex-
ceeds the maximum cutting diameter it will be shortened by the
integrated knife within the protective hood.
when the
Before each maintenance and cleaning work
− Stop the engine.
− Wait until the cutting device does not longer
− Remove the spark plug connector.
.
− Wear protective gloves in order to avoid injury
− Do not carry out maintenance work close to
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
Use only original parts. Other parts can result in unexpected
damages and injuries.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
The cutting tool will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the device carry out
the following maintenance works regularly.
Check the machine for obvious defects such as
− loose, hung out or damaged cutting tools
− worn or damaged components
− correct assembly and faultless covers and protective de-
vices
Necessary repair works or maintenance works have to be
carried out before the usage of the machine.
M
a
i
n
t
e
n
a
n
c
e
a
n
d
M
a
i
n
t
e
n
a
n
c
e
a
n
d
move.
to the hands.
open flames. Risk of fire!
M
a
i
n
t
e
n
a
n
c
e
M
a
i
n
t
e
n
a
n
c
e
c
a
r
e
c
a
r
e
Advertisement
Chapters
Table of Contents
