Table of Contents
Advertisement
Available languages
Available languages
Hold the machine with both hands.
Press the trip switch (12) and then the ON/OFF switch
(13). While working, you can release the locking knob (6).
To protect the battery the machine automatically
switches off at a low battery.
Do not continue to operate the ON/OFF switch. Oth-
erwise the battery may be damaged.
Charge the lithium ion battery (
S
w
i
t
c
h
i
n
g
o
f
f
S
w
i
t
c
h
i
n
g
o
f
f
Release the ON/OFF switch button (13).
The cutting thread is after-running once the lawn trimmer
has been powered off. Therefore wait until the thread is
stationary before you restart the product.
R
e
m
o
v
i
n
g
t
h
e
b
a
t
t
R
e
m
o
v
i
n
g
t
h
e
b
a
t
t
To remove the battery press the battery release button
(C).
W
o
r
k
W
o
r
k
You may not start to operate the machine until you have
read these operating instructions, observed all the in-
structions given and installed the machine as described!
Observe all safety instructions in any case.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
l
l
a
a
w
w
n
n
Correct working position
Before you start working it is recommended to adjust your lawn
trimmer so that you can work safely and comfortably.
Telescopic tube
The telescopic tube allows you to vary the working height.
1.
For this, slightly loosen the clamping nut (14) and adjust
the length.
2.
Then, retighten the clamping nut (14).
Guide handle
For better control, grasp the machine also at the front
handle (6).
Trimming
While trimming keep the lawn trimmer away from your body at a
sufficient distance. Tilt the product slightly forward and move it
from left to right.
It is recommended to cut higher grass above 15 cm in several
passes.
Guide the product around trees and shrubs so that the plants
are not damaged. Use the protective bow for better control.
Caution! Damaged plants may die off.
„Charging the battery").
e
r
y
e
r
y
i
n
s
t
r
u
c
t
i
o
n
s
i
n
s
t
r
u
c
t
i
o
n
s
t
t
r
r
i
i
m
m
m
m
e
e
r
r
Do not guide the cutting thread directly at walls and paving
stones. Otherwise it will prematurely wear off.
Thread follow-up
During trimming, the cutting thread wears (becomes shorter) or
it may tear off so that it can no longer cut grass.
Shortly press the running lawn trimmer against firm ground.
This will extend the cutting thread (15) (by approx. 4 cm). If the
cutting thread exceeds the maximum cutting diameter it will be
shortened by the integrated knife within the protective hood.
V
i
b
r
a
t
i
o
n
s
V
i
b
r
a
t
i
o
n
s
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous system or
to blood vessels may occur.
You can reduce vibrations:
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your fingers swell, you don't feel well or your
fingers become numb.
M
a
i
n
t
e
n
a
n
M
a
i
n
t
e
n
a
n
Before each maintenance and cleaning
work
− switch off device
− wait until the cutting thread is
stationary.
− remove the battery
− wear protective gloves.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
M
a
i
n
t
e
n
a
n
c
e
M
a
i
n
t
e
n
a
n
c
e
The cutting tool will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the product carry out
the following maintainance works regularly.
Check the machine for obvious defects such as
− worn or damaged components
− correct assembly and faultless covers and protective
devices.
Necessary repair works or maintainance have to be carried
out before using the power tool.
c
e
a
n
d
c
l
e
a
n
i
n
g
c
e
a
n
d
c
l
e
a
n
i
n
g
18
Advertisement
Chapters
Table of Contents
