Panasonic WJ-HD309 Operating Instructions Manual page 114

G Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
4 800/9 600/19 200 bps
G Control Camera CH
It is possible to assign camera channels to the RS485 ports
1 and 2 as shown below.
[Screenshot 1]
Start operation from the "RS485 Setup" menu.
SETUP MENU
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
z Move the cursor to "Control Camera CH" using the
arrows button (C D) and press the SET button.
[Screenshot 2]
The "Control Camera CH" pop-up window will be displayed.
SETUP MENU
I
Camera Control
CAMERA
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
x Move the cursor to a desired cell in the "TERM" column
using the arrows button.
[Screenshot 3]
The cursor will move to the selected cell in the "TERM" col-
umn.
SETUP MENU
I
Camera Control
PS.DATA Setup CAMERA
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
c Select a port by rotating the jog dial.
PORT 1: Control through the RS485 port 1.
PORT 2: Control through the RS485 port 2.
Repeat steps 2 and 3 to assign other camera channels
to be controlled through the RS485 ports.
114
Maintenance Recording Event Schedule
LIVE
Switcher Display Comm System
I
Baud Rate 19200
I
Control Camera CH
SETUP
I
Data Bit 8
I
NONE
Parity
I
1
Stop Bit
Maintenance Recording Event Schedule
LIVE
Switcher Display Comm System
Control Camera CH I
19200
Baud Rate
I
SETUP
Control Camera CH
TERM CAMERA TERM
I 8
Data Bit
CAM1 PORT1 PORT1 CAM9 PORT2
NONE
I
Parity
CAM2 PORT1 CAM10 1 PORT2
I
Stop Bit
CAM3 PORT1 CAM11 PORT2
CAM4 PORT1 CAM12 PORT2
CAM5 PORT1 CAM13 PORT2
CAM6 PORT1 CAM14 PORT2
CAM7 PORT1 CAM15 PORT2
CAM8 PORT1 CAM16 PORT2
O K CANCEL
Maintenance Recording Event Schedule
LIVE
Switcher Display Comm System
Control Camera CH I
19200
Baud Rate
I
SETUP
Control Camera CH
TERM CAMERA TERM
I 8
Data Bit
CAM1 PORT1 PORT1 CAM9 PORT2
NONE
I
Parity
CAM2 PORT1 CAM10 1 PORT2
I
Stop Bit
CAM3 PORT1 CAM11 PORT2
CAM4 PORT1 CAM12 PORT2
CAM5 PORT1 CAM13 PORT2
CAM6 PORT1 CAM14 PORT2
CAM7 PORT1 CAM15 PORT2
CAM8 PORT1 CAM16 PORT2
O K CANCEL
v Move the cursor to "OK" using the arrows button and
press the SET button.
→ Camera channels will be assigned and the "Control
Camera CH" menu will be closed.
Notes:
• When you move the cursor to "CANCEL" in step 4
and press the SET button, the settings will be can-
celed and the "Camera Number Setup" menu will be
closed.
• The assignment of camera channels will not be
applied until the SET button is pressed after moving
the cursor to "OK" in the step 4.
G Data Bit
The data length for communication will be displayed.
It is impossible to change the value for this setting.
G Parity
Methods to check a transmission error at communication
will be displayed.
It is impossible to change the value for this setting.
G Stop Bit
Number of stop bit will be displayed.
It is impossible to change the value for this setting.
r
[RS232C Setup] Settings for RS232C
Perform the following settings for RS232C.
SETUP MENU
Maintenance Recording
Switcher Display
I
Unit Adress(System)
Camera Control
I
Baud Rate
PS.DATA Setup
I
Data Bit
I
RS485 Setup
Parity
I
Stop Bit
RS232C Setup
I
Retry Timing
NW Setup 1
NW Setup 2
NTP Setup
G Unit Address(System)
A unit address (System) is a unique number assigned to
each system device. The addresses must be unique to
identify system devices when connecting multiple system
devices.
Numbers, "001"-"099", are to be assigned as the unit
addresses for the system devices.
G Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
9 600/19 200/38 400 bps
G Data Bit
Select a data length for communication from the following.
7/8 bit
Event Schedule
LIVE
Comm System
001
9600
8
NONE
1
OFF