Cleanup; Maintenance; General Repair And Service Notes - Titan MultiFinish 440 Owner's Manual

cleanup

Do not use gasoline to clean the sprayer.
Special cleanup instructions for use with
flammable solvents:
• Always flush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting flushed solvents in a one gallon metal
container, place it into an empty five gallon container, then
flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
IMPORTaNT: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material
to build up, seriously affecting the performance of the unit.
always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire
or explosion in the presence of flammable vapors.
1. Follow the "Pressure Relief Procedure" found in the
Painting section of this manual.
2. Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent (see spray gun manual).
3. Place the siphon tube into a container of the appropriate
solvent. Examples of the appropriate solvent are water for
latex paint or mineral spirits for oil-based paints.
4. Place the return hose into a metal waste container.
5. Move the PRIME/SPRAY valve down to its PRIME
position.
NOTE: hold the return hose in the waste
container when moving the
PRIME/SPRay valve to PRIME in
case the sprayer is pressurized.
6. Set the pressure to RAPID CLEAN by turning the pressure
control knob to its RAPID CLEAN position.
7. Turn on the sprayer by moving the ON/OFF switch to the
ON position.
8. Allow the solvent to circulate through the unit and flush the
paint out of the return hose into the metal waste container.
9. Turn off the sprayer by moving the ON/
OFF switch to the OFF position.
10. Move the PRIME/SPRAY valve up to its
SPRAY position.
11. Turn on the sprayer.
Ground the gun by holding it against the edge of
the metal container while flushing. Failure to do so
may lead to a static electric discharge, which may
cause a fire.
12. Trigger the gun into the metal waste container until the
paint is flushed out of the hose and solvent is coming out
of the gun.
13. Continue to trigger the spray gun into the waste container
until the solvent coming out of the gun is clean.
NOTE: For long-term or cold weather storage, pump
mineral sprits through the entire system.
14. Follow the "Pressure Relief Procedure" found in the
Painting section of this manual.
15. Unplug the unit and store in a clean, dry area.
IMPORTaNT: Do not store the unit under pressure.
English

Maintenance

Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
additionally, follow all other warnings to reduce
the risk of an injection injury, injury from moving
parts or electric shock. always unplug the sprayer
before servicing!

General Repair and Service Notes

The following tools are needed when repairing this sprayer:
Phillips Screwdriver
Needle Nose Pliers
Adjustable Wrench
Rubber Mallet
Flat-blade Screwdriver
5/64" Hex Wrench
1. Before repairing any part of the sprayer, read the
instructions carefully, including all warnings.
IMPORTaNT: Never pull on a wire to disconnect it. Pulling
on a wire could loosen the connector from the wire.
2. Test your repair before regular operation of the sprayer
to be sure that the problem is corrected. If the sprayer
does not operate properly, review the repair procedure
to determine if everything was done correctly. Refer to
the Troubleshooting Charts to help identify other possible
problems.
3. Make certain that the service area is well ventilated in
case solvents are used during cleaning. Always wear
protective eyewear while servicing. Additional protective
equipment may be required depending on the type of
cleaning solvent. Always contact the supplier of solvents
for recommendations.
4. If you have any further questions concerning your Titan
Sprayer, call Titan:
Technical Service (U.S.) ....................... 1-800-526-5362
Fax ................................................ 1-800-528-4826
8
3/8" Hex Wrench
5/16" Hex Wrench
1/4" Hex Wrench
3/16" Hex Wrench
5/32" Hex Wrench
© Titan Tool Inc. All rights reserved.